 Hey guys shave our 1,000 here as you can see We've got a bunch of stuff here We're going to try to make a little Drill powered pump out of some PVC Thought I'd do something fun today. So let's give this a shot. Okay. Okay. I got this rod here It's gonna be our pump shaft. I need to cut it off at the end this end seems to have a little bend to it And that's the end there. I do believe so we're going to just cut the end of this off You know one way we can find out We can put it in the drill chuck it up in the drill See it wobbling So I'm guessing it's just in down here so We got to make that straight first of all This is going to be our little propeller Impaler or whatever Propeller this is going to be our guide at the end Kind of like a bearing type deal This is what we're going to put that on the end of that with with this tap and dice that we have here Okay, so but again the first thing we got to do Try to find out where that's been I think it's been down here on this end Okay, so let me see if I can find find the bend exactly where it is and we'll cut it off And we'll go from there Okay guys, I Play around with this a little bit with that hammer, and I think we pretty much got it straight So this will work Now so I've got to cut this off so it can fit Inside of here say that Now I don't know if this is going to work or not We're going to give it a shot Okay, so the first thing I want to do is I'm going to mark this And then we're going to cut it off Okay So I just want to go Something like that. All right, and we're going to cut this off with the cutoff wheel Okay, but I'm not going to hold this in my hand. All right, so Let me get this cut off And then we'll see if if this is even going to work or not this piece may not work I may have to come up with something different before I go drilling holes All right, I've got a different plan. I've got a I've got a piece of stainless steel here That other Piece that I cut off. It's just not going to work So I'm going to try to make a round impeller out of this and I'm going to Cut it with that Let me get this drilled out Without Killing myself maybe I hope This don't start spinning on me. This one has enough power plan C That's what we're looking for places in this thing. Let's take this off of our bolt. It's not very centered So may not work, but At least we tried right can't hurt to try this is just this thing cost me anything guys This is a bunch of stuff. I have Land around though not quite centered But we're going to have to cut four slices in this maybe three might just do three so Let's see here Then I've got a got a straighten it out a little bit now This ain't my idea guys people's been doing making this stuff for years. I just wanted to try it myself so That's what we're doing Let me get a pen Now I don't want to go Clear to the center because I'll cut it in half. So I'm just going to go, you know halfway or whatever Just like that now I'm going to clamp these This is my trusty old vice grips here, and I'm going to cut this Four ways now I'm going to thread that rod and we're going to put this on there And we're going to give these a twist Okay, so I got to get you guys on the charger for a few minutes Okay, I brought you guys back as you can see I ran a die Down over here some people call them thread chasers, but these are actually It's actually tapping die set there is a difference thread chaser will not cut threads It just cleans them up these as you can see Cuts a very nice thread This is not a very expensive. Whoops This is not a very expensive set. I got this at a flea market for like five bucks or something so It was well worth that to me just You know to be able to do something like this even Even if they wouldn't cut threads very good, which they do it's all right I Could have always used them for thread chasers. This is also got It's got dies Taps and dies for pipe pipe thread too, so Let's see how we did All right, see that's Want to hold and like I said, I don't know how well this is gonna work guys but Of course Works on the internet just fine, right? So I'll get that adjusted where I need it to be because then we need something down here kind of like a bear Excuse me a bearing to hold this straight So now that we're done with that. Let me clean some of this up get it get it out of our way and Then we'll start on the pump housing and We'll go from there see that shaft It's going to run down through here. That's going to pick the water up down here Shoot it out there in theory like I said works perfect on YouTube But those guys know what they're doing they got better equipment than I do I mean some of the guys get serious and They like put all their stuff on on a metal lathe and they work all this stuff and put little bearings and stuff in And it works great But then you got a guy like me that just throws this crap together and it works just as good It gets me, but I'll be back with you guys hang tight Okay, so I did all that without hint and record But I got this on here and what I did was I bent these tabs back a little bit I don't think it matters because I can turn The drill backwards if I have to something like that I Want to get them somewhat Okay, so what this is going to do this going I've cut this off and I've drilled a hole in that So what this is going to do this is going to go down in here like this Very crudely, I've got my hole up in there get this lined up. There we go, and that's going to come out that hole Just like that now supposedly it shouldn't get Hot enough to melt this plastic because you know there's going to be water coming up through here So that's going to be all the time in water, so it shouldn't get too hot now I'm only going to want it you know just big enough just far enough to get the drill on it and What this piece is going to be for I'm going to put a hole in the center of this and it's going to go down over that Like that and that's what's going to hold This in from flopping around like that see how it'll flop around so I Think what I'm going to do is I'm just going to lay this across there. I'm going to drill my hole a Center's false one will lay this cross there and I'm going to cut a couple notches here Just cut out a couple notches and this should set right in there So that's what I'm going to do next okay, so this is what I've done I cut a couple notches down cut them sides out then I cut a slice around this way and The slice around this way that way this can Go on here and I can turn that and it locks itself in I'll also put a nut on the other end There so that way it can it won't slide out so now We're going to put a short end on a short end on here and we'll see if it works Okay, I've cut me off a short end Like that Now let's back you out In theory this should work the drill It's going to hook on there Just like that That's going to go in the water and it should pump water out So let me go get a big pan or bucket or something and I'll meet you outside Let's give this a shot guys My double nut came loose look and it was eaten in to the plastic Looks like Some what let me try to tighten this down all right guys I had to cut it down, but this is what I ended up with So I guess if I would perfect it it would work but on YouTube when they say quick and easy pump and It ain't that easy Everything's got to be precise and perfect so no air gets into it If I had lathes and all that kind of stuff and turn everything perfect I could do it, but I Mean it was pumping, but very little so there you go she bears a met the man The legend gone for now. Bye. Bye guys. See you