 I'll show you that you know when it's switched on there's 96 volts rms and the current is a little bit you know but I just don't think it's such a good idea being there and besides I would prefer if I can not have the 2V and 40V going into it because one it means I can't put it up on the shelf up there because the power needle sticks out the back which means the whole thing pushed out and it would be better if it was just a wire coming out the back and there's already a wire running up to this one up to the 4.9 volts even though that's reversed so that should be negative ah it's gone out again it's this here that maybe ah okay right well we just got a dodgy connection let's turn that off oh happy bloody days honestly honestly one thing then there's actually gonna be sort itself out for today like that's what the last bit of sold on here and get this baby to have a nice good old connections obviously not very happy with its connection I don't know that Banggood as well well like I say it's been one of them days it's just been a rough day today I don't know you know I don't know if you have days like that well today it's just been a rough day okay right fingers crossed uh that'll work and we've got hello guys sorry about that right so it does mean now and I can do a mission accomplished with this so let's let's let's check this out we should have minus 12 volts minus 12 volts we're drawing 100 milliamp positive 12 volts positive 12 volts positive 5 volts minus 5 volts and positive 3.3 happy days there we go let's see this is just going to pull apart we're going to take some okay so that's that one from there there all to do with that all we got here is the outputs here the switch power switch and that so I'll probably leave this in and just disconnect it of course we're going to use the switch I'm not going to use good and on the board here as you can see on the board it actually says what the voltage you know so your 12 volt middle one's ground the one to the right is negative 12 and then this one here is 5 volts and then the one on the outer is ground for the 5 volts so that's going to make life easy it's going to make life easy because I will probably cut these just in case I ever want to re reconnect easily take this out because we're not we don't want this it's only holding with one screw anyway not I didn't think that was connected in the lead that's on there I didn't know if it was going to connect to it but it is basically I'm hoping that would be so cool that it just fits I mean it was only connected in one screw anyway that and just for ease I think you're going to put it in this way around because that means that these leads can just quite easily go there there's that screw from here just to put it in some sort of place I think it's probably going to be best just putting that on the screw here I'm just going to put it like that just for now and that's basically what it's going to look like in there and then I can just put a hole let's say here or even there and run this wire up to that point I'll probably just put a hole just big enough for the cable to go through but you know tie a nut on it before I put it through just as that there's a strange relief yeah like that and then I can make the connection on the other side it's yeah I don't there's it doesn't really matter because I know it's going to be uh but that's basically how it's going to go and all I've got to do is now is just connect these wires up and I'll just touch soldering to these I think that I don't see the point in putting those um these connectors on I could do it on these cables I suppose I could put these in and fit because that means I've got to cut them and then there's going to be a soldered thing then they I suppose I could put some heat shrink on them and I suppose you know fit across the top just so or just soldered straight to that board that's all that board's going to be used for so I think you know I'm going to solder straight to the board I'm not going to mess around there's no point using all these things I can save these for other things there's no point and then once we've done them and I just chuck the uh the heat sinks on you on the um on the ones that I'm using there's no point putting them on the ones that I'm not using because they're not going to get hot but that's it so I'm not going to bore you there's pattern around doing that I've got a whole shave it running uh and then we'll do the voltage checks and then see if we've got any nasty 240 volt on the uh 212 volt on the and then see if the ground's well enough it would be you know I'll come back with nothing but I'm gonna you see the buzzer even though you can switch it off I don't mind the buzzer as long as it's not too in your face what's all I'm going to do with that is because I know that it's it's not terribly loud but it's me and that's just going to be annoying every time you press something you know uh but it would be nice to have a little time a bit of feedback yeah so because there's a little sticker I'm going to get a bit of this sticky stuff like blue tack but it's obviously not blue um and I'm just going to put that over it like that that's just shut it up I've just done it down so it's just audible just audible it was okay because you get feedback it's you know pretty quiet here when I'm doing this stuff so I'm going to use it to generate you know frequencies and stuff I want to be quite quiet anyway so okay right so we're connected up um this is going to be just the connection just for now going through to the switch and I'm back to the positive side and there's a negative side from the straight into the negative here and these are all just poked through the holes basically and connected there uh let's give it some power I suppose I'm five volts on tradition okay it's not doing anything dodging there we are um it's putting that down to three volts here so I'm just going to turn that knob you only get about 10 and a half volts 10.5 volts and this is good from five volts to 24 volts but what I'll do is I'll connect it directly into the 12 volts so I not go through the power supply just get direct to 12 volts so I've got to be a bit quiet because there's been a lot of noise so I've got to get the soldered on as I think but I don't know if you can see I've seen this because I don't know if we're going to get a whole bunch of voltage from the output that's an ac 19 bar but this is very 98 bar I suppose that's because it's an ac output so it's on a sine wave isn't it 3.2 volt rms that's about why it says 10 volt peak okay right put on the nothing's warming there and put on the uh the heat sinks and then we'll call it a night I think we're going to play with that drone for a little while and now that's another solar powered piece of kit down down here how'd you see you can hear this noise now don't it makes very subtle quite a trough for that alright cheers for watching guys I'll speak to you soon bye