 I Stuck some pots on I did these ones before yesterday I didn't show you but I'll put them on now. So this is going from the positive to the anode this is going from the negative to the Grid oh, no, sorry. I've got that all the wrong way round Right, this is going from the positive To the grid this one This is going from the negative to the grid So like I'm here, so there's a 50k pot there There's a 500k pot here here instead of the 22k resistor. I've put a 50k pot and Here right on 5k is a 5k pot where the four points 7 should be Yeah, that's still the same And these are 330 nanopores, and that's still the same this 100k pot here resistor Which is that sucker down there So we have a little bit of fapping around until you can about I got it It says 440 440 and 480 It says 400 400 millivolts But it says for well, it's flashing to 420 and 440 So what I'm going to do now is I'm going to disconnect these All these parts and then take values. I think that this could be adjusted more because this is right on 5k the adjustment and Well, if I Gotta put this camera Try to see you can see it This is all gonna go horribly wrong now because this takes quite a bit of balancing and messing about not the camera and the pots To get it, you know, it's all tweaked up I was just gonna show you the adjustment you can make so if I adjust the plate resist that Which is this one here if I adjust this You're gonna get to see over there. What goes on if this camera stays still We're gonna just it though and say just a little bit. That's not me enough But these are these are not sold or anything these pots So we see it dropping down now we're at 2.2 volts peak to peak near the same Begin now that's going past the 22k. I'm pretty sure now that's that's You know, that's all the way to one side of that pot. I'm pretty sure that's the 50k part It's on 5.7 to volts peak to peak now if I do the The negative side of the grid and adjust that Oh It's a bit sensitive down there. That's on a 500k pot And that's I was gonna say, I think that's all the way. That's not all the way to the 400k. You see now It's got like a bottom I start turning that back again And if I turn it further than that, we're getting a losing in So that's the deformity. Okay, then if I do the The grids again, but from the positive side and this is the 47k the 50k part of a 47k resistor You're real slow in general That's like all the way to the 50k But it's lost a little bit. So I just back it off again Now do it's not as good as what I did a minute ago But I'll probably have to go around the whole thing because if you're just one part then the whole lot needs to be Sweet again, this is back on the plate. That's just gonna Back that off a little bit Because on the plate should it be 22k. So it should be like halfway on this part If I turn that's halfway now. We've got 4.3 volts. I'll give it the 50k We've got 528 So I just adjust the positive to the grid again See if we get any more out of that. I just back that off slightly. Oh, that's the negative on the grid Lot of adjustment there Lot of adjustment now we're back on five five point five point eight Five point eight Volts peak to peak Now, of course, there's this one Down here as well. Well, that's on 5k and I mean it does adjust if I put it to 2.5k, then we start starts pulling out the bottom Just because I say you're trying to get my hand in there at this angle with the way this is set up But even if I adjust this so we're gonna have two hands, I can't can't show you What I'm trying to do is start just in the part way up So that's like halfway up now. It's probably got like two to two and a half k You can see that it starts around then off the bottom and pulling it up. We're down to five point four Now I know it's gonna try to adjust it back again. I'm gonna try and Get this back over the screw head There we go not pulling it out as you can see that but that's time to go back again So around five Take it all the way to the 5k I'm actually pulling it out That's like five seven two anyway five point eight again folks And it's pretty much all the way down that red marker looks right in So that's what you can do is wrap around put some parts on there And that's five point eight. We've got four point four going in and we got like five point eight This is set at one volt per division And this is that five hundred millivolts of division And yeah, there you go. I just want to show that so And what I'm gonna do is I'm not gonna do it right now on camera because it's gonna be a bit of a thing about is I'm gonna switch it off I'm gonna take off. I'm gonna take off each of these And I'm gonna measure The the resistance and I'll come back and tell you what that is on each of them. Okay