 All right kids, let's go take a look to see what's going on got a prep table that is Warm not cooling something. I don't know. So let's go find out what's going on. What's up north? What's up, Bill? What's up, Adam? Let's go play Okay, so it seems to be working now, but we're not sure What exactly the issue was you can see back there TXP looks like it's kind of crossing up pretty good I'm not sure if you just can't breathe or what's going on The first thing we're going to do is clean this thing out. That's pretty bad. I gave them a filter for it that compresses going out This thing's been hacked on but it's hard to say exactly what it causes So we're going to just investigate here, check pressures Okay, so I pinched it off because I was going to try to salvage the refrigerator in charge I put a filter dryer in there with a sight glass on it to utilize that receiver As you can see it pulled down into a negative 21 inch So our pressure switch here is junk It's sticking there's no reason it should have been off by 21 pounds So that needs replaced between the sticking low pressure cut out likely possibly low on refrigerant charge That's probably what happened here. So I'm going to Probably just recover this thing and change everything out get it back up and going. It's just Kind of a mess here with the way they've got that soldered in there Just use a flare dryer And a sight glass make it easy to get it in there But since this thing's probably had issues several times we're just gonna Get rid of all of it. We're just gonna recover all the refrigerant start over and fresh You know 30 years what we're gonna do now is go ahead and charge this juice juice up to see what we can get out of it See if we've got any circulation issues. I went over top of my Pinch off tool spot down here a little bit of brace around it to reinforce it So that that won't collapse on me later It's kind of on a weighted spot And then I'm gonna put some rubber in between here and and wire tie these together so they don't bounce Go on charge. So once we get done here I'm gonna stand up which that thing's been yelling Except in my truck for a long time. We scan this thing for leaks to even find something I did this thing was leaking way before they bought it. It probably is leaking in a cold rail just just kind of makes me think that because of The fact that when I was here last time it wasn't enough It wasn't really looking pretty acceptable right now That's gonna help us know when it goes well, they'll be able to just look at it It's like holds about two and a half pounds What you got to do sometimes unfortunately I'm gonna test my pressure switch here I went ahead and shut the cabinet off over there at the side here, which I'm gonna shut that off here in a second See what we get right back up and kick back on to the gauge that they have there on the patrol is actually accurate Be very surprising honestly looks like it's actually doing pretty good. It's really surprising. All right, let's turn it back on Let's see the refrigerant starting to coast through the side glass UTXV Is for the upper rail Just so we can we're crossing back pretty good, but you're also going hot air Decided around eight degrees This being a cold rail you got to remember there's no fans up here on top. So it's just pure refrigerant lines inside the casing there Fouls which This thing here go ahead and set it For a little bit back from the one side there Feel it running alone cold air two fans in there This one here has its own TXV on the other side, so So we were in super mode there we're just doing some scan and Going down to this rotolock fitting and that's with just 57 pounds of pressure on it for a four head Didn't have any leaks on any of my new fittings It's good. All right, this is really really really bad That rail as I should say the refrigerant lines are in the rail That's not going away a leak show up in the rail like that before The greatest time to try be looking for this When they're in a little freaking launch You can see we've got a full flage bar to go here So I'm just gonna let them know what's going on chances are there's nothing we can do about it Because there's no lines that are exposed up here on top All right, so we're back to finish up our leak check with panels out up here. I didn't get anything up there, but The infamous randle here has got Some oily looking stuff here, but it went off soon as I went into the container which you can see here Here we are on super as soon as you come in She was going nuts So go down to low because I already tried this out But come into here And soon as we get over here to these solder joints right here and right There went out the coils leaking too. So let's go ahead and spray that now right here's one right there Pretty good size. That'll be easy to fix. I can just reheat that Looks like I might have a leak back over in the back corner to you Okay, so we're also leaking on this side here. So leaking back here in the back leaking back here in the back and leaking up here on the front So we can Remove that bulb there re-braze those over seal that up, but I have a feeling that we probably got leaks in the Coil too, which is going to be kind of hard to tell with the leak above there So we had a leak down here on this thing too. So we're Going to remove it and put a new seal in there Sort of short small and we'll just come in handy Got a o-ring kit here. I shouldn't say o-ring, but I think it says no ring. So here we got some little kit here of nylon washers Should be able to find one that fits it. There we go So we've got it done up. I think that one over there was fine So we're gonna Spray this once we get it pumped up with some nitrogen pulled it around a little bit of a goober there But you got a lot of wires in here. You got to watch for it's why wire tied the one up and You know, it's this coil really should probably be replaced but unfortunately When you get that much leaking going on it's hard to narrow it down So we're going to pump up some nitrogen now and see if we got any leaks Maybe even get the ultrasonic out. Probably will use the ultrasonic. All right only place. I'm here in a leak It's right down there Up here where we're good to go. So we fixed three leaks total But I can hear something down in that area right there I'll spray it real quick, but chances are it coil needs replaced and if we do that probably do a new txc at the same time fringe benefits I love these people For my business owners out there a little bribery goes a long way So Yep, I can see a little bit of a leak Told you Right there at the very top You see it's down in between the coil there Yes, sir Right there at the very top. You should go see the bubbles And I'm bringing it that's 200 About 200 pounds 210 pounds area. So Um That coil's never gonna see that much pressure. So that's that's gonna make it last a lot longer than what it was We sprayed the top up there Nothing's leaking in that area. So, I mean I thought in some time obviously The state-age things are, you know tight, man, you know, who knows they may shut us back down again. So Can't make money. You can't spend money. So That's gonna help him out quite a bit at least we found Four big leaks on on the compressor suction liner Two on the txv and one on the line coming in feeding the txv. So Got those done. Let's go ahead and get this thing backing back out and get it recharged So I went ahead and sprayed this down to our door. Why would we have a part? Does not look like we have any leaks on that I'm gonna go ahead and respray my filter dryer and all my connections that I've made the last time on that And they all look good All right, I've got him a little bracket here That'll help hold That busted drain pan up for now. They want to fix it. They can fix it. Whatever I'll at least keep keep that there and get this all back together. So it's time to recharge this thing Since we didn't have the system open And we used nitrogen with brazen and all that happy jazz Um, I didn't pull out the big gauges. I didn't pull out the big hoses the Trader core removal tools my big vacuum pump all that crap. I don't do it every time I mean when it's under circumstances like this where Everything is pretty well dry and not to mention the evaporator is leaking So it's not like you're gonna pull a perfect vacuum anyway. So what's the point? Um, we basically bought them time to put it in all reality here, so We're getting this thing charged up both 40 ounces. We just put all new refrigerant in it Just uh, makes more sense to do that and it is to reuse it Okay, you see the cyclist there? He's starting to get to a little more here I just got to quote him some repairs yet and uh, he'll call this one a day If you guys like the video and you want to see more like it, you know what to do They're saying that it wasn't cold at all