 What is happening YouTube? Thanks for tuning back into the channel right here with the rust belt mechanic We've got right here a nice another set of our rust belts nifty tools This episode we're gonna feature four really cool tools that I found We're really helpful to me this week and hopefully they will be to you too The first tool that we're gonna come to today comes from auto direct and this is gonna be from a little place on Amazon This tool is gonna run you about $14.99 It's gonna be for you guys who are doing oil changes on the regular especially for the Cummins and diesel oil changes The oil filters on the 2017 and newer Cummins. They made it quite difficult for you It's a pain in the butt instead of being able to just vertically drop the oil filter right out of place They put this big stupid catch thing in the way and you can't get it out So what do you have to do you have to go through the wheel well to pull it out But you cannot just pull the oil filter out in the upright position It has to be tilted over what happens there You just dumped out a quart and a half of diesel oil all over the suspension and the tire and everything else in the wheel Well, it's pain in the butt So what do they come out with and this is just one company of quite a plethora of them that made this It is able to thread right into the oil filter Tighten down so then you can grab it and pull the oil filter out of the fender well Nice and easy without spilling a drop of oil it saved me a bunch of time and it's gonna save your shop a bunch of money in cleaning up in Break cleaner and whatever time it takes to clean up that giant oil mess the 1499 that this tool offers is Gonna save you guys a lot of money in the long run. I would definitely recommend it The next tool on our nifty tools list comes from Matco. It's gonna be part number PCP 42 480 this is gonna be a trim clip plier And it's gonna be for getting in the areas right around the hood Usually is what I use this one for and getting those two-part trim clips out Now why I say that these are a really nifty one is they are not the cheapest ones on the market these run right around 32 bucks right around there from Matco and They are actually ones that are gonna hold up I've tried quite a few different ones out the cheaper ones that are like five six bucks on Amazon by the time I get to using them on some of the more crusty vehicles those trim clips actually cause these to bend the handles This is the one that I've come up with so far that has not been any of the handles And it was actually a pretty decent price I've looked at a couple other ones snap-on ones that were about ten fifteen dollars more So for the price I thought these were awesome They're able to get in under the heads of the clips squeeze it spread the clips apart without having to pry on any other Outside surface so you're not really gonna be scratching up any paint You're not prying against any other plastic possibly damaging it You're right between the two pieces of the clips that you're trying to pry out. It's gonna be a really good tool it's gonna hold up not gonna bend and break and It's gonna make a really good tool for you guys to use in your shop as well Third on the list, we're gonna come to the snap-on torch 300 now I've had a chance to check out a couple of these different torches the torch 300 and the torch 400 is the next Size up as well that one was just a little bit too much overkill for what I use it for Inside underneath dashes doing some wiring some soldering work. This just fit the bill perfectly It does have a nice up and down to where you can adjust the output of the butane of it It is a butane torch the Selector right here. You're able to just see how much you've got inside the system butane fill is right here on the bottom I do like that it has a really nice big footprint So if you're soldering and you need to just set it down It's able to set there no muss and it's not gonna be falling over lighting things on fire Which wouldn't be very fun for you the heat range on this one is really nice It's able to heat up solder heat up shrink tube in a really small amount of time It's able to get into tight places and I like that it has a locking feature right here on the back You're able to light up the torch and then it stayed locked in place on until you hit the unlock button on the back To which time it will shut off It's a really nice efficient gun and it's actually on sale right now over at snap on for 64 dollars and 80 cents It made it into my toolbox and for the price. I think it should make it into what to yours as well Now as a pet peeve one of my biggest concerns in the shop is When I come in to work on a vehicle and especially when I'm working on the fan clutch of the front of a rear-wheel drive vehicle I go to take this fan clutch off and it looks like somebody's taken a long chisel a hammer and just pounded the crap out of it To try to get this thing off that just drives me nuts You guys need to get the correct tool to do it and this is that one This is the Lyle part number four three three zero zero pneumatic fan clutch wrench set This is going to be a seven-piece wrench set. That's going to be used in conjunction with your pneumatic air hammer going to lock right into place with the clutch and then these are going to go right onto your fan clutch nut hub and then you're going to be able to use the leverage from this to unhook and Loosen your fan clutch instead of just taking an air chisel and pounding the crap out of it You're going to be able to use this both directions the one that you're going to use most often It's going to be your 36 millimeter Actually, I don't think I've even touched the other ones in this set before this is pretty much the only one It's a really great tool to use and it actually is a really good price also for what you get for this one at $116 it's a fantastic buy for not having to really mess up somebody's vehicle Instead of having a pissed-off customer. Why not just use the correct tool and get the job done, right? This is the tool to do that And in keeping in good form of shouting out some channels that I think are good up-and-coming ones for you guys to check out The best one from this week is going to be Junk from work. He's a smaller YouTube channel of about 520 subscribers. He's very well spoken He does really great videos. He does tool builds. He does builds in his garage He's going to do some meters some test leads. He actually knows how to use in a soloscope So given you guys some know-how on some electronics just some in general things that he does in his garage He's a really good channel for you guys to check out so make sure you go and give him a follow and Maybe you guys could be on the next one make sure you guys keep up with your good content and keep regular On those videos. I'm checking out all kinds of smaller channels here and there So just keep it up guys. You guys can make it on here as well Well, that's about all I have for you guys today for rust belts nifty tools of the week I hope you guys enjoyed this one and videos like it if you did make sure you hit that thumbs up button Make sure you turn on that Bell notification So you get notified when I come out with cool new videos like this one go and check out my Instagram account I've been coming out with some really cool new additions throughout the week If you guys want to follow me throughout my work week here I post a lot of pictures just in general of me around the shop and what I find Thank you guys. I appreciate it and as always You guys stay awesome