 Hey everyone, Shaber1000 here. Today we got another Christmas decoration that we need to fix this belongs to monkey's mom and I have replaced the bulb because the bulb was burnt out, but Even though it's tight There's an issue there. It's not the bulb So we're gonna take this apart Let's see if we can figure out why it's doing that. It's not safe. Let's make it safe and pretty again Okay, guys. So like I said My guess is there's a loose wire in here So we're gonna have to take this bulb out. Let's just piece of cardboard up off here. We'll see what's going on with it first Let's unplug it. There's the bulb. I'll be very careful this thing. It's ceramic sometimes these wires right here get loose and Sometimes down in here They'll break inside. You can't see them, but it's looking like it's right up in here Let me turn another light on here. Okay. Let's see Looks like there's a little bit of corrosion there It looks like it might be rubbing Right down there. It's like it might be cutting into that. Let's see if I can get you to focus on get Yeah, see right there Hey, so first thing I'm gonna do I'm gonna hook these wires Get you over here That helps any and I think what I'm gonna do is I'm just gonna go ahead and cut these wires cut the ends of these wires off Bring the wire up through a little further and Reese Cut them back and Reinstall them and see if that takes care of our issue And they're on the bottom there. There's a little nut. We'll be taking off It's got plenty of wire. So I think I'm gonna Cut off about Just in case it's right in here. I'm gonna bring it up through until this is up here I'm gonna cut off about four inches of it So what I want to do just push this up through here Like that right there is where it was coming through here. So I want to cut Cut this off here Make sure I'm plug it now take this off When I screw this a little bit say You can see here. Let me get this to focus There's little crimps there My guess is that's where our problem was in one of these because that's what was Rubbing on that Right down the edge of that right there So I'm gonna back this out a little bit farther All right Make sure I've got enough wire here and I do Okay, so what we're gonna do now I Got these old things These things work great sometimes Let's get a little bit more out of there. I'm not sure how this thing is but Judging from the bulb it takes It's probably pretty old I'm not sure how old I know it's monkey's mom's And a bulb was burned out so we went and bought a new bulb Which I found two or three after that in the garage that I had But that's okay So we had to buy a package of them which I told her that's probably what we have to do They were cheap we bought them at the dollar general store so Brought it back put it in and it just wasn't working right, so I Decided better take a look at it. So through here about right there I'm gonna bring that around that way. I don't have the right solder for this Because usually what I'll do is I'll go ahead and form these the way they need to be Then Like all I'll do something like this Something like that Make like a hook and then I'll put solder on it so it stays, you know, so it stays in that I have put ends on these before but I don't like doing that. They just seem to me like they don't Those ends are cheap And it gives you less room to work with and But these were like this from the factory so Which can do sometimes Just take that screw clear out Twist it around make your own eyelet Sometimes that works well. It's pretty good. This one. I Don't like the looks of it. So Let's do this one again. It's kind of like all frayed. I'm afraid not. Okay It's a joke about that you guys ever hear Tell to you sometime. It's a dad joke like I told Monkey about the rumor I had I heard about butter But I'm not gonna spread it around Okay, so let's get this around here. I gotta make some room on this card. So hang tight guys I'll be right back with you. Okay. That's better. I was down to one minute. Let's get this Down in here the best we can Get this tightened up. Let's see what I did. All right. I'll speed you up through this So what I forgot to tell you guys was the reason why I Didn't take these screws clear out because they're not designed to come clear out they They'll come out so far and then stop so And when you you can still take them out if you put a little pressure on them, they'll come out but The same time when you go to put them back in the threads what it is is the threads are messed up on the end on purpose so When you go to take them out well Then Like I said, you can get them come out. They're not real hard to get out. But when you do take them out They will they don't want to go back in because the ends of the threads are messed up So and then when if you do get them to go in sometimes it screws up the threads that it's going into then Then you have the situation of Of it not Of stripping out where it goes in then you got to replace this whole piece here. So this is tight now Let's put this back on and let's put the Sorry guys Back you out now put her ball back in that feels kind of loose. Let's check that All right, let's plug it in Gotta switch on here with shut it off plug it in and turn it on There we go. All right, there we go. That's better and we fixed it. Yay That's one Christmas thing we have fixed so there it is guys, let me get a Shot of that for you in the dark. I'll turn the lights off here. There we go. There we go Cute little light. Yeah, maybe I can use that for my thumbnail. All right guys. Anyway, shea bearer the mytho man a legend appreciate you watching And We'll see y'all in the next one. So Hopefully I can keep on my video a day until Christmas, but we'll see Sometimes I'll record a few days ahead That way if I don't feel good or something you guys still have an upload to watch So anyway There we go Thanks for watching guys appreciate it. Y'all stay safe. Take care and bye. Bye