Loading...

How To: Aqua Volta Cavendish 9 at the tap, Pressure-free operation of the switching valve

1,112 views

Loading...

Loading...

Transcript

The interactive transcript could not be loaded.

Loading...

Rating is available when the video has been rented.
This feature is not available right now. Please try again later.
Published on Apr 8, 2017

to install easiest way to create a water filter (Aqua Volta Cavendish nine former. Moses 9) on a faucet.

IN VIDEO RECOMMENDED

Aqua Volta Cavendish 9: https://www.aquacentrum.de/shop/aquav...

HydroSelect - three-way valve for water filters:
https://www.aquacentrum.de/shop/hydro...

Video for handling the plug connections:
https://www.youtube.com/edit?o=U&vide...

Video Another way of wastewater management:


I will show you the simplest version of the port to which you installed the Aqua Volta Moses the tap.
All I need to know I read in the manual in the chapter "Connecting the tap on the diverter valve".
Tool I only need a 22 ger, a 12 he ended spanner and the connector tool.
With the 22 strength-end wrench I loosen the aerator on the faucet and screw it down with your fingers.
There are other taps with smaller or larger aerators measure or try in doubt, and select the appropriate wrench.
The sealing surface should be clean.
I select the right adapter in which I compare the diameter and thread pitch.
If the gasket from the aerator is still good, I use it again, otherwise I take a new one.
The seal I Fummel so to the adapter, which keeps them on their own now I screw the adapter "hand hard."
Now I take a pair of scissors and cut my two hoses, the interface I press back around with your fingers.
So now I have two pieces, rather let too long, can I trim later still.
Now I look again at the manual.
How do I get the hose because it?
Quite simply, unscrew the nut and then slide it over the hose the hose stuck in the hose.
If that's difficult, I'll do the tube with a lighter or with hot water warm.
The union nut back and replace with the 12 he tighten wrench. Then I check if the hose is secure.
Now I screw the valve, with built-in seal to the adapter. Here also "hard hand" is sufficient.
If it is not tight, take a pair of pliers to help, but there is a risk that is damaged chrome plating it.
So, let's see how it feels.
Manual check, next point. Now the ionizer's turn.
I put the unit face down on my work surface and below I see the water connections and the power cord.
With the connector tool or just with your fingers do I remove the plug and lift this!
The hose I'm in the right water connection.
There is also an extra video on using the plug-in connections, you'll find the link in the video description.
Now the device comes into place.
Even turn around and look pinched nothing.
Here I moisten the drain hose and turn the suction on the drain hose on it then I'll bring it in position and suck him.
Another option for wastewater management, I show in another video.
Link in the description.
Next, I take the plug out of the connector and keep it with the other plug together.
Then I turn one the pump hose by hand until the end.
Now comes the plug into the socket and on the rear panel, turn on the switch.
this will appear in front of the display:
to stand up now and nice for positioning pump hose.
After I show how to use the device properly.
Use of the diverter valve and flow adjustment on the ionizer, on the faucet installation.
Turn the knob of the Ionisieres to "ON".
turning the changeover valve in the direction of the hose.
The cold water, very open.
Adjust the flow to about 2.0 liters per minute.
Now the water draw off to make the faucet at the end and let the ionizer that.
Now you can turn the switch valve toward sink and turn on the tap to get hot or cold tap water.
This is called the pressure-free operation of the switching valve.

Loading...


to add this to Watch Later

Add to

Loading playlists...