 Hey guys, welcome to another Impressa Ice Racing Impressa video Right, yes We've been working hard today and it's time. It's been a while, but it's time to Finally paint the car and we do actually have some Painting experience I painted a car 12 years ago about 12 years ago It was a super action Look here painted a car, which ironically not was also a subgroup 1313 years ago. Yeah The difference is I used rail cans and he used an actual Spray them. No. Yeah. Anyways, we thought we would Combine our 25 years of experience and apply today for our our special project But we had to do stuff. We've been actually working for 12 hours Okay, we started at 11 30 and it's 8 30 8 30 p.m. Right now All day We just work slow So we made a paint booth Can you guys see us? We're right here Blending in Let's take a look inside This is cool or what? All right, so you can see we attached some Mines of wood So we could attach this oil plastic Got some weights down Then we'll get this pretty cool. So we got a fan blowing air in and not just any air It's warm air. We got a here behind the fan Because we're trying to raise the temperature of the car Where it's 50 degrees and we need to get 55 60 60 supposed to be six. Yeah, it's only 10 degrees off So keep going You can see It's took 12 hours guys 12 hours not 12. It's 10 10 hours. Sorry. Anyways, we're gonna be painting the bumper We're gonna be painting this This panel Right here Because we found some rust we're painting this inside here You like this taking up job Don't paint this here because of some rust over here now this fender remember we did some we move some dense up top Got some band up top. Obviously, it's gonna be lower right then here we got the Bumper which I once again look broke. So we're gonna paint this first We're gonna move it aside lower the car Keep painting and stuff. So we even got a filter So this is actually sucking your in out obviously So you can see the oil is actually blowing out So which means that's what you want you want Positive pressure positive. Yeah, I guess positive pressure. So you don't get any So the air kind of through all the different holes and cracks comes out out of your paint booth if it was the other way around and all the Dusts would come in so you want it out. So we actually achieve that with these fans that fan is kind of it's weird took us a little bit to adjust but Seems to be fine now. We actually have this one sucking in at top speed, which is three and that one blown in at one which Should give you the other opposite effect, but I don't know. It is what it is Anyways, we have this door over here So that heater was blown Too much air at the plastic and it was all kind of going crazy. So we installed a supply with the bucket No paint booth heating issues. So actually look actually went out and bought an actual paint That's what we're using Sam flexible primer surfacer thing This is serious guys, you know, we're trying to do this right We are clean the surfaces with this stuff strong stuff. We got actual paint It's over there That's No, that's that's for the paint. Yeah, okay, so that's the paint. That's a reducer and no, that's for clear. That's that's the clear cold That's hardener hard or whatever Ultimate overall clear cold is what we're using in case anyone is Wandering with this and this is the the paint the base Okay Sunfire pro standard base cold same color by the way, because remember it needs to pass inspection And I went to Bobo Freight and bought the second cheapest gun they had Yeah, maybe you want to mention that that thing needs to be cleaned out and it was oh, yeah We had actually made a make a special tool to remove the The nozzle and the inside as it was glued because it wasn't it wasn't provided And then what is this? Central pneumatic a whatever. Yeah, maybe just someone just took it from the box see this so Took a 1116 and made it, you know, you know, okay anyways That worked out Obviously you got some special suits over here Got strainer steering sticks and all that Thermometer to check the temperature of the of the surfaces trying to reach that 60, right? Which will never will anyways That's it, right? Yeah ready to start ready to roll. Yeah, so since Luke has one year over me of experience He's gonna do the painting You're gonna let me go first. Yes. Okay, sweet Don't open the garage No, no, no Don't worry. It's not gonna catch on fire. We tested that so primer. It's just the whole parts of the hood parts of the fender And all of the bumper you think all of it I have I have no clue put this in the vice Okay, also, I don't feel like holding it man. What? Oh, watch Luke spill. I'll let you do it There you go. I'll watch you Can you grab this panel? I don't have a panel for this All of it? No How much? Do you need to mix this or not? Oh, all of it I just realized we don't have any water to clean this Something's not right. We're gonna be sanding this It doesn't even sound Sounds weird No, no, this is this is something wrong, man All right, so that didn't work, but we have a different gun which I had for Long time 10 years or so and never used Less matter less less pressure So we think the needle is too small for the for this paint or primer in this case But the guy that the professional, you know his own store, you know paint store That the guy that was selling the paint to Lucas said you had to use a 1.3 or a 1.4 needle since the cheap guns I guess you can't get replaceable or different needles I'm not even sure if it's called a needle, but the tip right the tip needs to be 1.3 or 1.4 But clearly not enough paint is going through the gun You know to have the spray pattern that we want The paint actually says on the can or in the instructions it says use a tip of 1.8 or up to between 1.8 to 2.0 Which is clearly Much bigger than you know 1.3 for example But look is determined. He's going to put down the first coat coat of primer on that bumper at least So we'll see how it comes out Take a look run out of primer But it's not looking very good. I mean this is our fault. We didn't do a great job Of you know Bando and sending it and whatnot, but I don't know if you can see it, but you know, it's not looking very good here. We ran out So we do need to send it basically after it dries for a little bit Look is gonna actually there is a little filter right in here, right? There's a little filter there Yeah, we'll see what we just took it out But it seemed like it was clogging up here. Let me let me close the door Hold on I gotta go that way Don't spray yet Door locked not the best Seems better All right, now we're gonna try this new gun without the little filter inside and where where's the filter? Oh Here are the filters in question Or just the black you don't need to spray the whole thing Because it's got paint on it just the black parts There you go Here it's next. No, this is just light light clothes here And the other side Hold on. Let me be this way For primer first go It's late 10 30 We're cleaning the guns You may have to get another cheap gun tomorrow. Let's see the result two coats so far So I sprayed it. I was holding the gun closer about six inches from the Car And it is better. It's more smooth Still has this orange peel look to it, but I guess that's normal primer Yeah, I don't know. I mean obviously we don't know poop about painting But look Will this ignore this because that's just some stuff that fell on it here No, look at this It's much more smoother than here for example, you feel that Just by holding it closer So here because there is paint And you know most of this we you don't have to prime it as long as it's got paint you need to scuff it up a little bit And we used 400 or 220 we used 220 to scuff up the paint and just put primer on Bando or exposed metal basically We found some rust spots. So that's why you have these different Random spots This fender is rusted by the way You know, we may replace it After some time. I don't know We'll see But look check this out. Look see how smooth this is After scuffing it But it's rough here, but we need to you know sand it. We're gonna let it dry Overnight and pick up tomorrow So actually scuffed scuffed it with a green scuffer Before the second coat And just held the gun closer So, yeah, I mean check this look. This is probably the best part But what you're already cracked. Well, that's that's our Bando or uh fiberglass It's fine. It'll send out. It's fine. So next I'm not really sure. Uh, I turned off that fan And look what happened Yeah, so now it's we have the sucking situation here now Yeah, so so you see guys. So this is still working on highest speed That one there was on on one this whole time. Yeah, I'll turn it off in a second But that one was working on on the lowest speed and we did have the You know the bubble effect or whatever you want to call that Now let's turn that off the blowing in one and now we have the The sucking effect Which Lucas likes All right, I guess We're good So so all right guys I guess we're gonna pick up tomorrow in part two. Bye