 What's happening YouTube? Thanks for tuning back into the channel this week for rust belts nifty tools of the week We've got another four tools here for you to be able to show you what I've used this week What's helped me on my job and what could hopefully help you guys in your jobs coming up, too? We're here first just so we can go through that to get it out of my way here But this makes my job so much easier when you're doing Services when I am doing intakes on these 3.6 liters anytime I need to clear any kind of amount of fluid off of the engine bay or off of the transmission if I want to do a Transmission service, and I don't want to have all that transmission fluid Just dump down all over when you take the pan off this thing's really nice to suck it out of the way This is made by mighty vac the part number on this one is seven two zero one It's really nice that it comes with three different extensions one that I don't have shown here The main one is this larger diameter to which goes to a smaller one Which could go to a smaller one yet to fit into the tubes that for filling that you could shove down into the transmission to suck Things out and it's very nice because it's got quick disconnect fittings You're able to connect it together each one of them And then it also has a drain here on top this stopper plug unlocks pulls out So you can just take the whole thing and tip it over when you've got it nice and filled here The cool thing also about it is that it does both suction and it puts fluid in So if you've got a differential that you've got you know kind of a hard place to get and you can't put another Fluid insertion tool this works great for that one all you have to do is there's a little plunger right here on the side You just push or pull up on it changes it from suction to pressure and it is hand operated They do have one that is the 7300 model I believe that is able to hook to shop air but this one just for what we need to drag it all around the shop It's just hand pump Right there. It does have a nice little foot stamp right here that slides out So you can put your foot on to it to balance it and it's not all shaking and wobbling all over the place All in all it's a really great tool for the money It helps save you guys a lot of time you can find this one on the trucks Usually they charge about 200 bucks, but if you want to save yourself some money They do have this one on Amazon for right at a hundred and two dollars Like I said, this is the mighty vac part number seven two zero one Next on the nifty tools list is kind of be this inner tie rod tool by Mayhew part number on this one is two nine nine One zero it there are a couple of different manufacturers who make this one But mayhew I found is the one who has most of their stuff stamped on it And you can find just about the best deal and price on it It does have a rolling clutch here in the end of it a hollow tube to where you can put your inner tie rod into for a long distance Great for those trucks that have those extra long tie rod ends and then here on the end It is a nice one inch I believe and to it so you can get a socket or a wrench onto it and This thing is fantastic in just about any place. You can get it to all of the tie rods that you have these days They're all rounded ends. They don't have that nice nut end that they used to anymore So having that one way locking clutch tool makes it really nice now This one doesn't just do the single direction this one will work for tightening it as well So all you have to do is put it on there the one way clutch locks it into place as you start to turn it You turn it a little bit harder and it locks into place Break your tie rod and loose and when you're pulling it back on twist it a little bit harder It'll lock into the on position and then you're able to tighten it up This is a great tool to have rather than trying to get a set of spanner wrenches or something like that into those Subframe areas doesn't work so well. This works fantastically. I would definitely recommend for you guys to have this tool Now this one it was available on the truck for right around 200 bucks But like I said, you guys can pick this up just about anywhere on any truck Everybody has this one as pretty much the standard tool and you can even pick this one up also on Amazon For a hundred and twelve bucks, which is I think a pretty darn good deal Third on our list of tools for the week is going to be the astro pneumatic Riv nut installer tool. This is a 13 inch Riv nut installer part number on this one is going to be 1442 This one is great for getting into different areas. I use this primarily for Installing riv nuts underneath of vehicles for running boards if anybody knows dodges you have to install the riv nuts on your own So not every once in a while Do you really have the time or anything to get all of your air tools or electric tools up there to use their? Installation tools which also fail quite often these are made of a very nice solid steel It's 13 inches you're able to adjust the tension and the length of the fitting So you're able to adjust for a smaller or a longer pull on it It gets a lot of really good leverage and it does come with six different bits The different bits are for you know everything from let's see an m5 m6 m8 and then in the standards It comes with a quarter 20 10 24 and a 5 16 18 The really cool thing that I like about this kit is it comes with a whole bunch of bags of Rivnuts for you as well. So not only do you have the tool you've always also got the riv nuts to be able to install They do have the knurled ends to keep them from spinning when you go to put the nuts in But usually I don't have any issues with that one This tool does install them very nice and tight like I said You're able to adjust the depth on it to pull a little bit more if you really need to So it's got the riv nuts for every single one as well as the tool end for Installing that the different tips onto there It's really strong tool. I definitely would recommend that one especially for you guys who are metal Fabrication guys who are installing the riv nuts all the time dodge guys who are putting running boards on all the time It works great for me. I would definitely recommend that one They do have these on a couple of the Matco trucks that I have found But not too often they definitely didn't have this on a snap-on truck He had to special order this one for us at the shop But I also did find this one online at a tool vendors or Amazon This one ended up running $68.05 which is a pretty good deal for you know what we use it for I definitely recommend that one We've been using it for about six eight months now and haven't had a single issue with it I definitely recommend that one for you guys Last but certainly not least on our list is the Matco BTS 8 this is a newer tool out or tool set by Matco It is primarily for battery and battery tending usage for cleaning the posts It's an eight-piece toolkit everything. It's got three different ratcheting ends the wrenches for taking off your battery terminals It's got a long eight millimeter end one or five sixteenths, whichever you prefer It also has a short ten millimeter one as well They are reversible ratcheting and wrenches a nice rubberized grip Then the shorter eight millimeter one The longer eight millimeter has a smaller looks like a thinner end pry tool for being able to help pry up on some Of those posts that are extra stuck on so that does help and then the set of battery clamp jaw pliers I was kind of confused at first on exactly what these were for four But they did say they were they were recommended to be used for Battery nut ends that were rounded everybody knows those little squared ends on the ends of the battery nut So the battery bolts they always seem to spin when they're absolutely not supposed to so when these things clamp They clamp down at a flush flat surface with a little bit of a space to it Able to clamp right on to and hold on to those battery nuts and those battery bolts that are spinning on you Makes it a really nice little tool for you there a standard battery cleaner for the nub end and then it also It does come apart and then able to clean out the insides of the rounded cables That's just a standard tool that just about everyone has Then the thing that I really like about this kit is the small puller. Everybody knows those battery clamps They always get mangled and they get crusty all the battery acid or here in Ohio Just rust in general. So this puller is a nice end to it. It's able to adjust the end tension You're able to screw it in farther and then pull the Turn this silver part in and it actually clamps the ends in to be around your battery cable Twist that in to push the battery cable up off of the terminal ends makes it really nice This one also secondary tool works great for windshield wiper arms That's actually what they sell it for separately this single tool. They call it BP T7 is on their part line This is probably one of the best parts of this kit And then a last over here on the ends. There are two little Battery terminal brush ends one that has a quarter inch fitting to be able to put on to like a quarter inch nut driver or a quarter inch Socket end squared and then the quarter inch just standard hex bit nut driver to go into your bit drivers Nice little stiff wire brush and if we're cleaning off all your terminals really good kit Online they're a little bit pricey through Matco if you just purchase them online It's like 92 bucks if you purchase it through their site But this week on the Matco truck and their flyer they are running a sale because it is a new tool I ended up picking this one up on the Matco truck for right at 78 bucks You know some of you guys might say you have you know piece together It's kind of a pain and it's a little bit expensive But again the tool truck comes to me the warranty for the whole set is well worth it to me I would definitely recommend to have this one. This is going to cover just about every battery purpose need for the tools that you'll want And finally in keeping with good fashion of helping to shout out some smaller channels Some of those channels that didn't get a great start the diamonds in the rough people who just haven't had their time to shine This week we're going to be talking about SNR motoring SNR motoring is a pair of guys who love doing a little bit of Fancy race work out of their home garage. They've got a couple of really cool projects going on My favorite would have to be the mark 3 supra build that they're doing and they also have a Chrysler Conquest TSI. I believe is the other one that they're building on they love go fast parts They've got a great amount of humor good quality picture audio in their different videos that they have I think that they're going to be a bigger channel coming up They're just you know kind of starting off over the last six eight months or so But I think that once they get some traction here from you guys. I think they're going to be really taking off I would definitely recommend for you guys to go over and check them out They're going to be coming out with they say at least weekly videos and they've kept up with that Religiously if you guys want to be featured on the smaller videos I just want to make sure that you guys keep right with the different styles of Different content that you have and as long as you are also regular with your content as well That's one of the biggest things that all of the viewers like to see is once they understand the schedule and the kind of Viewing that you have then they just want to see that you know continue over the time So I would definitely recommend that you guys keep on doing that. So next week. It could be you we'll see We're about out of time now to be able to talk about our nifty tools of the week Hopefully you guys enjoyed this content. Make sure you guys stay tuned this weekend I've got the Duramax bug and we're going to be doing some more fun Duramax build I'm getting a couple of more sponsors and we're going to be doing some really cool fuel additions to the Duramax this week We've been adding on some power We put a little bit of transmission work in this last weekend now We've got a beef up a little bit our low pressure side of the fuel system a couple of the other little add-ons We're going to be doing a great video for you guys this weekend that one should be coming out on Sunday Tomorrow evening Thursday evening if you remember a couple of weeks back I gave a shout-out to a gentleman named Jason from old car auto guy review He does a lot of cool things. He's up in Canada. He's got a smaller shop Or a sorry a smaller dealership and he just in general has really cool things on his channel They do a live stream every single week on Thursday evenings helping each other shouting each other out Talking about some tools auto reviews things like that I am going to be actually helping to co-host on his channel this week So if you want to catch me tomorrow evening make sure you guys cruise on over to old car auto guys review And we're going to have a really good time there We want to beat their subscriber count that they have for the people that are hanging out live So we want you guys to be able to show up for that one. Have a good time It's going to be a great little evening for it Thank you guys I appreciate you tuning back in if you guys like this video make sure you hit the thumbs up turn on that bell notification So you get notified when I come out with cool great content like this one We're going to be continuing to do this segment every single week on Wednesday. I appreciate it Thanks again guys as always You guys stay awesome