 Okay, today's gonna be a little axle replacement going on here. I got some really bad u-joints And my rear axles a lot of slop in there going on So we're gonna rip this all apart and I'm gonna replace the axle and I'm gonna show you what to do here It's actually not too bad of a job So first things first we're gonna remove this bolt Take this out so we can bring this arm up get that all out of the way Take this off remove the whole hub area Hopefully everything should come out. So at the nine sixteenths socket And don't lose any parts. So you got a washer down underneath here Little rubber grommets Keep in mind the orientation of that side That could probably stay there Remove this to get it out of the way because this all has to come up. I think this is a half inch Well, I had to get a My backup gun here. So I had a different one. We're good to go 916s we're gonna pull this out now before I pull this out I'll take this this nut off in the bottom with right to your home So it's kind of doing a little stubborn. So Taking a hammer we'll pull that out. You'll loosen that nut And I used that leave it to inch and a half take this off and there are two washers there I keep keep that all intact keep that in mind. I think there's a couple behind here, too Slides right off. I don't know who worked on this last but somebody put a Goofy looking bolt in there. That's not supposed to be there. So I'm gonna replace that that was this side It's nice 916s we can pop this out now in between here of these Little I don't even know what you call them like a spacer Pop this off pull out and then These need to come out. So I think What I did the one time is just kind of grab it and pull it there we go That all comes out now depending what model you have This is a 97 500 there's actually a bolt holding that in place way up here I think the 98 99's they just pop off is a little clip on there You just grab the shaft you pull it hard and pulls out of the transmission So I'm gonna have to get a Wrench, I think it's half inch and unbolt that and then this is all slide off Okay, another good tip to let you guys know that I have both the axles out of the transmission right now What I said earlier there was a bolt on each side well What happens is you take one side out and And actually basically the one side bolts into the other Important to know because I'll sudden you put this side back in and you start taking this side out And you're wrenching on this bolt on this side And that side's gonna come loose so yeah, it's all basically One whole piece of bolts together. So take one side off leave that bolt loose And you go to take the other side off like what I'm doing right now Nothing there hole in it. You just pull it straight out and You're ready to replace 97s like I was saying there's a bolt in here your splines go into the transmission and So what I got here is you got my wrench on like I was saying before and I spinning it You also have to put a wrench on the other axle and hole it the same time you're turning this though Otherwise, it's kind of like a nut and bolt You got to hold one side to get the other side out And I can't do that while I'm holding the camera So I'm just gonna do it. I just wanted to show you guys make sure you got a wrench on the other Side of the axle when you're spinning that bolt out So try to give you a good shot here Well up the shaft and there is a bolt Right at the end of the shaft And I am taking the 916 inch wrench and I'm just turning it little by little And I had to leave the one tire on the ground. So this doesn't spin Yeah, I'm just going little by little and it's slowly coming out It's like a little bit So now we got that bolt loose Pulls right out And now You that's a nasty mess. I'm gonna clean that up and Yeah, basically just do the Reverse of what I showed you and while you're this far cleaning everything up grease everything up your grease rucks If you'd like to make if you'd like me to make a video of me putting it back together just Yeah Drop me a line if you got any questions. Feel free to ask a please subscribe to my videos I've got about 50 players fixes on here You know, like I said, there's not much to it. Just do the reverse of what I did Put everything back together and you should be good to go. Thanks for watching