 Hello, and welcome to this presentation of the STM32H7 Embedded Operational Amplifier. It covers the features of this IP, which is widely used for conditioning analog signals. Each of the two operational amplifiers inside STM32H7 products functions as a general purpose analog amplifier, which may reduce the need for an external standalone op amp. As these op amps can be configured in standalone mode with all terminals available for the user, it is possible to use them as a voltage follower, non-inverting and inverting amplifiers, as well as analog filters, such as low or high-pass filters. They can also act as a pre-amplifier for the ADC input. The operation amplifier inside STM32H7 products offers general purpose rail-to-rail inputs and outputs. The input offset voltage can be calibrated in the application to achieve minimal offset. All the terminals are accessible by the user so that any operational amplifier function can be configured with external passive components. When the op amp is used for the ADC input, the ADC sample capacitor must be charged over a very short period. To support ADC input requirements, high-speed mode is available. The slew rate becomes 30 volts per microsecond instead of 3 volts per microsecond. The op amps also provide on-chip functions, including voltage follower mode, while their on-dive feedback resistance can be used for the programmable gain amplifier function. This slide shows the block diagram of the operational amplifiers. The STM32H7 integrates two operational amplifiers. Several switches are used to configure different functions. Each op amp can be configured individually. The operational amplifiers support this default configuration using the factory trimming values and operate in normal mode, highest performance. The operational amplifier can be configured as an internal voltage follower, where the internal switch connects the output to the inverting input. In internal voltage follower mode, the GPIO pad assigned to the op amp's inverting input is free, so that it may be used with a different function as subsequently assigned in the GPIO selection process. The op amps support non-inverting amplifier mode with four fixed gains available. The feedback resistors can be selected to have a gain of 2, 4, 8, or 16 to support the programmable gain amplifier function. It may also be beneficial to use the op amp as an ADC input, so that the full dynamic range of the analog to digital converter can be applied to signals having a small amplitude. The op amps also support external connections on outputs and the non-inverting input to create the PGA mode. It enables the connection of an external capacitor to add low pass filter characteristics to the PGA configuration. This STM32H7's op amps support inverting amplifier mode with four fixed gains available. The feedback resistors can be selected to have a gain of minus 1, minus 3, minus 7, or minus 15 to support the programmable gain amplifier function. By using this configuration, it is possible to shift the bias voltage of the input signal with AC coupling capacitor. It can also be used as a non-inverting amplifier with a gain of 2, 4, 8, or 16 with bias to a zero ground voltage. The op amps also support external connections on outputs and on the inverting input also for this PGA mode. It enables the connection of an external capacitor to add low pass filter characteristics to the PGA configuration. The operational amplifiers are active in the following low power modes, run, sleep, and stop modes. In standby mode, the op amp is powered down and must be re-initialized for use if returning to one of the higher power modes. The following table shows performance parameters for the STM32H7's op amp. All values are preliminary. The op amp can work from 2.0 to 3.6 volts from the VDDA supply with rail to rail input and output. The offset voltage can be calibrated down to 1.5 millivolts. It has a gain bandwidth of 7.3 megahertz. Thanks to its high speed mode, the ADC sample capacitor can be driven very effectively. The STM32H7's op amps are suitable for the pre-amplification of the ADC input because the integrated PGA can enhance the dynamic range of the analog to digital converter. Its high slew rate can drive the sample capacitor of ADC very effectively. It is handy to use as an on-chip voltage follower instead of using an off-chip standalone op amp. This is a list of peripherals related to the operational amplifiers. Please refer to these peripheral trainings for more information if needed.