How to Replace a Vinyl Floor with Ceramic Tile | Ask This Old House





The interactive transcript could not be loaded.


Rating is available when the video has been rented.
This feature is not available right now. Please try again later.
Published on Mar 9, 2018

Ask This Old House general contractor Tom Silva helps a homeowner replace the peeling, vinyl floor in his bathroom with a ceramic tile floor
SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse

Time: 2 days

Cost: $200

Skill Level: Moderate

Tools List for Replacing a Vinyl Floor with Ceramic Tile:
Open ended adjustable wrench [https://amzn.to/2PTcMUd]
Utility knife [https://amzn.to/2MXO9n9]
Pry bar [https://amzn.to/316D4ni]
Hammer [https://amzn.to/2UuaXvL]
Putty knife [https://amzn.to/2NYqiDg]
Jigsaw [https://amzn.to/2MUH4Uo]
Carbide tip knife [https://amzn.to/2LwUliB]
Notched trowel [https://amzn.to/2PU0sTI]
Drill driver [https://amzn.to/2ZQS4nM]
Wet saw [https://amzn.to/2PS7b0y]
Rubber float [https://amzn.to/2ZOqbAw]
Sponge [https://amzn.to/2PPnpHG]
Bucket [https://amzn.to/2PQKbyK]

Shopping List:
Tiles [https://amzn.to/2UyvNdg]
Cement board [https://amzn.to/2MXMAWb]
Thinset mortar [https://amzn.to/2ZETd6v]
1 1/4 cement screws [https://amzn.to/2UxmQ45]
Mesh tape [https://amzn.to/2Q1qRiG]
Grout [https://amzn.to/2MVlb7j]

1. Before getting started, all the appliances need to be removed. Disconnect and remove any sinks, vanities (https://www.thisoldhouse.com/how-to/h... ), and toilets (https://www.thisoldhouse.com/how-to/h... ) in the bathroom. Loosen the flange and hold it up with spacers if possible.
2. Next, remove any baseboard trim with the pry bar.
3. Once the floor is clear, peel off the vinyl tiles with a putty knife. With the floor up, now is good opportunity to ensure the subfloor is properly secured.
4. Add cement board to the subfloor to act as a base for the tiles. Cut it to size by scoring it with the carbide tip knife and snapping it, similar to drywall.
5. Apply the thinset to the floor using the notched trowel.
6. Secure the cement board to the floor using the cement screws about 8” apart. Make sure the cement board goes underneath the toilet flange. Cover the seams between the cement board with mesh tape.
7. Dry fit the tiles to see how they will fit in the room. Measure and mark tiles that need to be cut.
8. Cut the tiles using a wet saw.
9. Apply thinset to the cement board using the notched trowel and lay the tiles on the floor. Nippers can be used to cut around the flange. Allow the thinset to cure for 24 hours.
10. Grout the tile after 24 hours.
11. Reinstall the vanity and toilet.

Tom chose a mosaic 12x12 inch tile with mesh backing from Daltile ( https://amzn.to/2MYJ3qH ).

For the subfloor, he used 1/4 inch Wonderboard lite cement board underlayment [https://amzn.to/2Ltl4gd]. For mortar, Tom used versabond thinset [https://amzn.to/34r6ZZf].

To trim the bottom of the casings, Tom used an oscillating saw available at Home Depot ( https://www.homedepot.com/b/Tools-Pow... ).

All of these materials can be purchased at a home center.

About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.

Follow This Old House and Ask This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/ThisOldHouseTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/ThisOldHouseIG
Tumblr: http://bit.ly/ThisOldHouseTumblr

For more on This Old House and Ask This Old House, visit us at: http://bit.ly/ThisOldHouseWebsite

How to Replace a Vinyl Floor with Ceramic Tile | Ask This Old House


When autoplay is enabled, a suggested video will automatically play next.

Up next

to add this to Watch Later

Add to

Loading playlists...