 Hey everybody, this is Brett with Summit Auto Reviews and today I'm going to be installing this Oledro hard tri-fold tonneau cover on this 2021 Ford F-150. This tonneau cover is gonna fit your 2015 to 2024 Ford F-150 with the five and a half foot short box. I'm gonna be unboxing it, we're gonna be installing it, showing you how easy it is as well as going over the benefits of having a tonneau cover. Now, if you like the tonneau cover and how it works in this video and how it looks, you can get it one in the affiliates link to Amazon in the description below. Get a little bit of a cut on that. Really appreciate it if you buy one, but let's get right to it, get this out of the box and get to installing it. I'm sure it won't take that long. All right, so I already have all the things cut, all the tape is cut, and I figure I'd put it in the back of the truck so that I could get it out easily without dropping it or anything. And it folds up just like so. You get all your clamps that have to go on to the tonneau cover right here. And they're nicely packaged in this foam and has wrapping around them. And then there's this piece right here. We'll find out what these all do. And it comes wrapped nicely in the bubble wrap here. So we'll get all that off. You can probably fast forward on this. And you can see it's a really nice heavy duty tonneau cover. Probably a two person job to get it out of the box. I just don't want to damage it because it is such a nice tonneau cover. Now that we got it out of the box, we can get the box out of the way. So you can see that this is how it looks when it comes out of there. You're going to want to probably undo all the tape and the straps. Then you're going to want to figure out which end goes to the back of the truck and which end is at the front of the truck so that you can install it properly. Which I'm going to do right now. And then I'll show you how I did it. All right, before we start anything, I recommend that you open up your entire tonneau cover before putting any parts on it because when you completely open it up, number one, you want to check to make sure that there's no damage to the tonneau cover before you install it. Last thing you want to do is spend all this time installing it, realize it's damaged and have to take it all apart. But the other thing that you're going to get when you open it up and make sure it's not damaged is you're going to find not only the instruction manual, but you're going to find the foam piece that goes at the top of the bed. There's also a light in here that you can attach anywhere. If your truck doesn't have LED bed lighting like this one does, you can attach this light in here to make it brighter inside. So that's the first thing, open this up, check it for damage, make sure there's nothing damaged on it. And then number two, you can get your instruction manual and your foam piece here. And I'll show you how this foam piece goes on first because that, okay. So the first thing you're going to want to do is grab all your parts here. And a lot of this stuff is just spare parts. Like these pieces right here are spare parts for your sliders on these things in case they break. You get two of those. You also get a spare snap like so. And then you get a spare piece right here for putting those snaps in in case one of those breaks. So the first thing you're going to want to grab, and this goes on the piece closest to the cab are these two wing nuts and then the metal clamp downs. That's the first thing you're going to want to do. And you're going to be putting these clamps so that they are going to be securing underneath the bed rail. So you just put those on like so and then you can put your wing nut on and then we'll be putting it on there and then we can tighten it down once we get it placed. I'll put the other one on and we'll get it going right away. So I'm not going to be actually installing this on this truck because this is not where the tonneau cover is going to stay but you just want to take this adhesive off. Make sure this area is clean so you want to get a wet rag, wipe this off, make sure it's clean and then you're going to want to take the adhesive piece off and you're going to want to just make sure that it lines up evenly. Go from bed rail to bed rail and then you're going to want to cut it with a razor or a scissors or something and then just stick it down and make sure that it's nice and sealed and then it's not going to go anywhere and then you can get to putting your tonneau cover on. For this demonstration, I'm not going to actually install this so but that's the first step. Onto the next. Okay, so remember the clamps got to go basically the clamp side faces the top of the tonneau cover, put that on there, get your wing nut, just kind of loosely put it on there like so and then we're going to put the tonneau cover and place it onto the front of the truck here. Keep in mind these are, this is a fairly heavy tonneau cover. The whole thing is pretty heavy and we're going to put it on here. We want to make sure that it's even on both sides before you put it down. You're going to want to line it up with your seal that you put on. So the other thing when you're getting this, let me lower the camera here, these seals right here, just line those up with the bed rails so that it's even on both sides. And then what you're going to want to do before we tighten this down is we're going to want to close the entire tonneau cover and make sure that it's fitted properly lengthwise and then we'll clamp everything down and we'll be all set to go. All right, once you get under here, this is pretty easy. All you have to do is make sure your clamp is underneath your bed rail. Now there's instructions in case you have a drop in bed liner. You're going to have to cut some holes but just turn your wing nut up until it's nice and tight and that should be nice and secure. And then you're going to want to do the other side. Once again, just put it up there. Just make sure it's nice and snug and that's as easy as that. Now we can put our other clamps on and be all set to go. So you're just going to want to grab one of your clamps out of the parts foam and you're going to want to get the clamp through the screw here and then there's a nut. I don't know if you can see it but there's a hole right there and we'll get it on there and you're going to want to get it into that nut and then just turn it on like so. And that's what it should look like when you have it on there and then that can tighten it down for you. These are safety clips so once you get it in place you're going to want to put that clip in there so stuff in the back doesn't knock it open. Make your ton of cover go flying on the highway. Once again, you just want to get that bolt through the hole like that, get it right into the nut and turn it on. All right. Now we can close the next section of the ton of cover and bolt those down. So now that we have these all set to go, you're just going to want to turn it until it's up underneath the lip of the bed rail. So I'm going to have to tighten it just a little bit more. It's kind of a trial and error. So when you get it under there and you push it down like that, that's what tightens it so we're close. So it should be nice and snug. You want to make sure that that's not going to go anywhere. And then you can put your safety pin in so that it doesn't open up accidentally. What that does is it just protects it, prevents it from opening up in case luggage back here hits it. Those clips are a little harder to get in because it's hard to see. So there you go. So now the clip's in and now it won't release on accident. Now it's the same thing for the driver's side. Just going to want to turn this until it's close. So you know, that's probably too tight. You don't want to make it too tight either otherwise you might break that plastic piece there. There you go. Now put your safety pin in and we're set for the final piece. So now that we have our clamps on our last piece right here, just going to want to put it down. Once again, make sure your fitment's all nice and snug here. Looks pretty nice and even everywhere. Just going to want to grab that clamp, turn it, get it up enough so it stays nice and tight. All right. Now it's nice and secure. We'll do the other side and we'll do some final shots with the tonneau cover on so you can see how nice it looks and we'll be all set to go. Basically want to just turn it all the way up to the threads. I think that's a pretty good start. Now it's all secure. Once again, verify. Oh, and you can put your sticky on. So you take that out, it's got adhesive on it, just peel it and put it wherever you need a light and then it's a press button. You're going to need batteries with that but let's close its tailgate and shut it nice and solidly. It's right even and flush with that tonneau cover and you can see just how nice that looks. Really a good looking fold up tonneau cover. Yeah, I think it looks really good. Get a side view here. So there you go. So I hope the video was helpful to you to get your Allegro hard fold tonneau cover put on your F-150 and if it was, give me a like, subscribe and share on the YouTube channel. I really appreciate it. And if you want to get one of these tonneau covers in the link below is a link to my Amazon affiliates page. You can get this very tonneau cover off of there and really a nice tonneau cover. It's got a nice texture to it, looks really clean and I think for the price that you'd pay for some of the other brands out there, this Allegro piece is a really, really nice tonneau cover. Thank you so much for checking out the video. Remember to like, subscribe and share and until our next product review and installation, have a great day.