 Hello boys and girls I got a repair video for you decided in the middle of the job to show you what's going on with this 03 BMW 325ci now the problem was the wipers the wipers basically were out of adjustment What I suspect happened was they were frozen in or heavy snow, whatever the driver used them to clear the snow and The wipers did the motor turned but the wipers didn't and it went out of adjustment Out of its out of its you know original spot and they end up in Different place when they're free to move what these wipers were doing as I would turn them on They would go down first get stuck and go up and stop right here Obviously, that's an issue so I started reading up on forums and You know different places on how to fix this obviously it wasn't a relay Which is right here if you take this cover up. There is a wiper relay right in this corner over here So I started digging many people what they would do is Adjust the arm or They would hold on to the wipers and turn them on and then that motor would slide on its axle or on this I'll show you that later and It would you're basically stripping back. There are splines where that arm goes on to and you're Stripping it back. You're putting back the Wipers in its place, but that's you know, you're you're damaging the splines on the motor more and you don't want to do that So what I ended up doing obviously you got to take some stuff off I'll show you that later. I'm gonna put them back on so you can see How they go back on from watching that you can you'll be able to tell how to take them off I actually took the whole assembly off What you need to do to take if you do need to take all of it off There's a 10 mil right here upside down. That's a 10 mil you take that off And you take these off the wipers And there are these long nuts or big nuts over here these are 24 this is 15 Same on this side Once you get these off rotate this whole assembly so you can actually take this This bolt push it down Don't forget to unplug it But if you don't then then the whole thing comes out This way, but if you don't need to take it out, which you don't need to in my case Doesn't matter where the wipers are stuck in the middle down up whatever You don't need to take but as long as they're working you don't need to take this off As long as your motor is working, but what you need to do is you see that nut right here on top here This is what you what you're working with. This is a 13 mil What you're gonna do is you're gonna loosen this nut up. You don't need to take it off. Just go out maybe Eight threads just so you have enough room to remove this arm from the spline The splines are right where that nut is and you're gonna use Take a long screwdriver And you're gonna pry this up Like that So you're basically removing the this arm this rotates This rotates the clockwise as the wipers are turning or working so you're gonna Push on that pry it up That arm will come out of its splines Then you can move the wipers and this arm will turn the motor will stay in place The arm will turn you're gonna move the wipers up and down adjust them and Tighten that up again. Now I had to do it probably maybe eight to ten times Because the wipers would end up Either here here here, you know, it's gonna take a few tries But if you're gonna wanna there there was a problem. That's why it took me a little bit to figure out so that's what it looks like when it's Adjusted correctly this arm right on right above the nut I hope you can see this right above this nut this another arm that's connected to To this wiper that's in the way right now That's right above that nut the nut you are working with and if it's gonna be like that There's no way you're gonna be able to tighten it up again. So what I had to do I turn the wipers on and When they would end up right on top straight up. I would take the key out Actually right, you know somewhere about here and then I would tighten up the nut and Try it again. See if they're you know right about here. That took me about five Five tries, but when the wipers are up right about here That arm on top of the nut is Out of the way and you're able to tighten up that nut. So this is what you got to do each time you're gonna Tight make an adjustment and need to tighten up that nut You need to turn the wipers on once they're up turn the key off So they stay up, you know work the nut and until you get it just keep trying So now I'm gonna take all the plastic parts out and show you how they go back on. All right, so first piece Is this this is kind of heavy actually this is like some kind of heavy-duty Plastic these tabs will go down Like so somehow Maybe these bolts are t30 torx torx bits Okay, now it's this big guy Next these are also t30 bolts Okay, now I forgot this Rubber seal this one did not come off. All right now the filter Now the cover for the filter I gotta take the wipers off and Put the final cover back on this goes on less than Done and that's it boys. Hope this helped you out as always like subscribe and I'll see you soon