 Hey guys, welcome to another painting party It's not good It is not good if you missed the first episode. Well, we kind of we started priming the Impressa We had some issues with the gun Well, both of them Actually, the issue was with the guy that sold us the paint. He told Lucas to use a 1.3 Size tip, but the instructions on the primer will clearly clearly says To use two point one point eight or more or higher like between one point eight To two point. Oh, it's actually right on the can right here. It says fluid tip One point eight to two point. Oh now the paint and clear does say one point four Which is what we had but Lucas went to get a different gun So we'll see but we are determined to paint it today No, put down the base that may be clear cold. It is late. It's 5 p.m. I'm gonna send it now It is rough you can't see it But you can hear it Here this that's not too bad Bad Not too bad. I Mean everywhere we had overspray everywhere. Yeah, so I gotta do the whole hood fenders And the bumper then gotta clean the dust up. I'm gonna actually vacuum the floors everything from in here It is kind of cozy in here. I like it And I'm gonna dry send it I don't want to make any more mess and I'm gonna send it with 220 then maybe bump it up to 300 or something like that or maybe 400 we'll see Probably not just trying to get this as quick as I can All right, I'm not gonna show you the sending process because it's just it's you know, you don't want to see that All right guys, I'm gonna show you the result when I'm done that was something we're not gonna see much, but Like before you might be able to hear it, you know my glass My goggles. All right, so it's still it's still dusty, but I Remember the noise Noise is the same. It's a little less noisy But it's the same everywhere. So what you want to do is basically use one hand to Send it and the other to kind of follow and feel Feel out the roughness Like okay, I just found out I need to do a little bit more here because this part is smoother And this part is smoother then this part here So gotta go over I'm gonna blow this off with compressed air and go over it again, but Send paper saved the day. Hopefully, you know, I should probably mention if you're here to learn something about painting Turn this video off right now. All right, it's Clean up time guys pro tip of the day Trying to spray directly on the plastic. I did a kind of a test spray here and All the reason for this is because this plastic The paint doesn't stick to it and it flakes off. I actually you can see here. It's flaking off So what happens is you come back to spray after this dries. Let's say, you know second day or whatever Like we are today and these flakes will make may Go on to the paint while you Spray we both knew about it, but you know, there is special different kind of Plastic covers that paint does stick to You both knew about what we forgot about it and it is it is what it is Look here going to town with 400 grid. Look at him go Mm-hmm What Orange peel well, we won't have any orange peel right over right here You got a look at the bright side man Yeah That's maybe a lot of orange peel day You should probably do the best over there You know it's like trying to polish a third We actually read the instructions after Yesterday after we did all that of the paint gun You may want to do that before you start painting So two things You can thin a primer or use a bigger Needle for the gun like a 2.0 jet Jet whatever you call it. Yeah, not sure you know what we have to do when we're done with paint You should have been Painting all this door Maybe like right over here. Well, no, this is this is a test panel man. Oh So what we're gonna do is Once paint is on because we may Send The the paint the first base We're gonna cut this foil here and kind of just big out give us a bigger Yeah, bigger working area over here, I gotta put my respirator on Same thing over here No, we're taking this seriously guys. This is serious stuff. All right, so in about five four to five hours When look is done, we're gonna clean this off and be ready for paint and Same gun Just new maybe we'll see maybe that one had an issue after all it was From the China store fingers crossed. All right guys Cheers We're ready to spray. It's not looking very good guys You know, like I said before if you're trying to learn something from this just turn this off right now You know go to a different video where an actual professional is you know teaching you how to spray But we did watch a lot of videos You know quite a quite a bit. I've been watching these kind of videos for years now 12 12. Yeah, 12 at least 12 years Almost read a book about about painting body working, you know stuff like that But you're not gonna see any of that here Really say almost doesn't count almost doesn't count. Yeah almost almost doesn't count so it's probably gonna look Worse or as bad as it was before just colored this time And I may just take maybe just throw in some pictures later on when it's all done Do some close-ups of the primer maybe and you know after after base So you can see how bad it really is Who's gonna spray this time? Just pots and stuff Couldn't show you because I was holding loose hoes And we did the whole primer with paint. This is the second hope Keep the wet wet edge We're going to go and pick up the weather you guys were done spraying the paint Gotta clean the gun after each Use really but who's who's got the time? But we are cleaning it after the paint now Getting ready for the clear coat Let me show you. Let me show you Wait, we're wrong way. I'm gonna show you what kind of a Painter look is we had to fix our door So as we Kind of you know walk in we kind of lock ourselves in with this two by four just kind of set this Plastic on the floor and just put some weight on it. What? Yeah, this this is this is actually high-tech guys. I mean look at this fully protected All right, I mean fan everything And we already showed you this but look let's look at the bumper you're not gonna I don't know if you're gonna even see this. Well, there you go this is our You know not so good preparation Which we? Didn't really pay too much attention But this is not too bad No, it is I Mean we didn't put Bando on here Especially over here not very good Luckily we don't care, but this is actually not too bad besides this dent that we didn't fix We learned that we gotta keep the gun close And we no longer head. Let's see if we can hear this This is smooth actually Not so smooth So we do have some dust we've been wiping it every Before every new coat we gave it what 10 15 minutes dry time and then we would Just wipe it and wipe up the dust With with fiber cloth, you know just like this you can actually now I can feel how rough This is This is a little bit less just by keeping the gun close Six inches or so if you keep it too far, then you have this, you know, you're creating this dust On your finish. Oh, it's bad Especially over here Or if you can tell but See how quiet that is and how loud this is. Yeah So we are going to send this with 600 800 excuse me 800 we're gonna Peel this back and just Retape it This is rough. I mean Because we didn't spray directly on here. Just just you know, we only had an area to paint Which was right about here But you know how it goes So this is rough over here. We're gonna send this down I'm gonna peel this back probably tape it up here again Same over here peel this back Okay, so let's compare colors You can see a line, but there's no ridge. So that's good news so we can Lightly send this kind of blend them together and just You know put clear coat here Bumpers not too bad You may not even have to send this Down at all Same here story here Kind of left this open See less less roughness here. I don't know. We're kind of experimenting too Here you can see the The tape a little bit So this needs some sanding down again rough over here for some reason and Besides these some of these dents here. This is not too bad No, I gotta say So far, I'm pretty happy with the hood defenders and the bumpers not so much with the front bumper guys We're gonna end it here for part two of the Painting Impressa project. We're gonna hit clear coat tomorrow Stay tuned. See you next time