 What's up everybody? How's it going? That was my very fancy not fancy timer gonna have Caleb make me a timer for this channel Better do that. Let me know How you doing? If you can hear me if you can see me, okay? It looks like we're okay We have Hey Sarah Johnson Jonathan Barnes, how are you? Andrews sink what up? At a man commented a little bit earlier. He lives near me. He says he's jealous. He's on the list to get one of these Andrew sink says I'm gonna love it. I Think he's chatted that on on Twitter. He said I'm gonna love this thing and I I think you're probably right looks fine Sounds fine. I like it Not gonna waste too much time. I'm gonna give maybe just a couple minutes local maker, Michigan. How are you? fellow member Just making sure I'm good All right, now I can hear my notifications if you guys Decide to choose to Maybe Contribute we can't get out here We're setting a timer Apparently my stuff isn't attaching that's okay though Hi, Jim hi all from the BC. What up? Jim Hutchins Jim Nance all the gyms are here all the gyms are here, and I love it We're not gonna waste too much time. Like I said, I'm gonna get this bad boy out We're gonna get it printing while it's printing. We'll unbox the wash and cure So today we are checking out the Mars 3 from Elgu I know there's bunch of videos out there some other people did live streams already and I wanted to get in on that fun So this is the Mars 3 And this is the mercury X Washing cure bundle it's two separate machines a wash and a cure machine and From what I've seen on other people they packed this thing just Majestically in this box battle cry. How are you Brian? Weber how we how's it going builders mark what's in the box a Mars 3 and a mercury bundle mercury X bundle So we got some fun stuff today. We got an overhead view today And I was rushing and didn't get my side view set up. So we're getting front and overhead today. That's it But that's okay, right What up, how you doing fellow member shout out You guys want to be a member it is like 299 a month to jump in on the coffee club I think and like 499 For the higher tier and we're gonna be doing some fun stuff So watch this week members for some Member only posts on Facebook. I think I'm gonna do another hangout with you guys And I might even do like an unboxing like this just for you guys. It'll be fun big channel. How you doing the pooch rock lives I Think he printed that on his stream. I still got it right here. He joins us on hot makes sometimes the pooch rock He's looking very dapper today. His hair is Very very nice. Yeah We're not gonna waste too much time. I'm gonna jump into this bad boy. I'm drinking some bubbly Some lime. I don't know if you guys have had this lime bubbly But it tastes like seven up but like without the real harsh sweetness. It's so good Do a hangout on Thursday. It might be able to join in. All right. We might be able to do that It might be Thursday night though We get that out of the frame So what I'm gonna do is while we're talking I This was a last-minute stream I wanted to get this thing done and I just I needed to get it scheduled and do it So I'm gonna drop all this stuff. I'm gonna I'm gonna go All sorts of full screen on this one So I got screen and chat. We got everything. Hopefully the noise from the fans is not Too prevalent The back area is a mess. I've been filming and not filming and filming I got all sorts of mess going on here I can do most nights nice daughter loves those drinks. Yes, they're so good Let me know if the fans that I have a fan going and the air conditioner behind me if that makes too much noise Let me know See is this connected yet son of a gun? It's not all right. Let me grab a knife. We're gonna jump right into this Happy Sunday everybody. It is a gorgeous day here It's gonna be like I think it's gonna be like 80 degrees low humidity like 40% humidity, which is great And just a beautiful day. I got a pile of boxes over here So we're gonna be doing a lot of live streams in the next couple weeks probably at least one a week Good can't hear any fans Well, I hear fans you guys are talking to me That's a good one, right? All right. I'll do Mars three I Know a lot of people are really digging this machine Uncle Jesse is loving his Andrew sink is loving his if you have one in the chat Let me know I better not spin that around because all my address stuff is on there So we pop this bad boy open And I'm gonna test my top down camp So if you guys are not aware tomorrow on hot makes we have just an amazing guest guest host Devon from make anything. He's gonna be with us tomorrow And I cannot wait because not only we're bringing Devon on we were bringing Marcy the mixed media girl on she does all sorts of crazy Acrylic pours and paint pours and all sorts of fun stuff. I found out she has a print farm And we're gonna talk to her about that as well. I didn't had no idea. She 3d printed It'll be a lot of fun. So come check us out But Devon and I I don't know if Marcy is gonna do it or not But Devon and I for sure are gonna do our very first Acrylic paint pours live tomorrow night. This will be all set up like this probably and will be like mixing paints and pouring and making art Live on stream and I cannot wait. It's gonna be so much fun I I sent Devon a starter kit. I picked up a starter kit and I think it was like 70 bucks 68 dollars or something like that from from her website from Marcy's website mix media girl calm and I can't wait to check it out. So that'll be a lot of fun Also, thank you so much to thanks for sponsoring this video. I I should just have it scrolling Let me fix that I'm gonna fix that Anybody donates today. We got some fun graphics. Don't forget. It is not Expected but always welcome and if you hit me on PayPal, I will get a notification. I believe Let me just double-check nightbot. I don't know what nightbots been doing today Because I didn't look at it today, but if you hit me up with yeah I'm gonna have definitely have to do some plastic down or something if you hit me on PayPal Google doesn't take all my money. It's like 30% if you do it Like from here and it's they don't take that from If you do it on PayPal, so let me We just see what I got here memberships like and subscribe Hot makes channel, you know, I'm gonna run the hot makes channel Nah, I won't do that today and okay Good, so I think we're good on nightbot and I just want to jump into banners and Let me just jump in here And I'm gonna I'm gonna scroll some banners thinking things and Maybe not. I lied. I'm not gonna do that mostly because Yeah, there we go banners let's see Create a banner real quick. Sorry guys. Um, there we go boom Shaka laka. There we go I like it we'll get a little uh boom There perfect. Sorry Stoked on this one. Andrew sink me too, man Speaking of Andrew sink. We have an epic show tomorrow with devin for make anything and marsy for mix media, but next week I'm screaming. I hope I'm not clipping next week Andrew sink is going to be our special guest on hot makes he's our special guest host And that's going to be a blast. I love Andrew. He's a ball of fun Awesome personality and uh, just just a ton of fun. Um I was thinking wambam mat. No, maybe I don't think wambam mat's going to be big enough for the canvas We're doing tomorrow. All right. Let's do this so We're going to do this. I haven't played with my top down top down camera. Yes. This is the first stream with this Okay, I just set it up So we're going to pop open this lgumars 3 You guys are going to see what's inside of course the white is going to blow out But that's okay. I'll get over it As long as you will right I have their big mat depending on how big yeah, I I'm probably just gonna like lay down I don't know what I'm gonna lay down yet. So you saw there's some uh foam and some more foam a little booklet Foam, yes, lots of foam. Hey, look at that more foam Boom, so that's how it's in there is a lot of light up there, but there you go You can see it says lgum. I might have to change my lighting up a little bit, but that's okay Andrew needs a pooch rock in the background. Yes, Andrew. You need a pooch rock a very special one You can you can you can dress him up? However, you would like this is my very special We'll call him tropical pooch rock He did his makeup today So there's that All right, let's get back to this so What do we got here? We got a we got a box of stuff. I'm just gonna try to do it this way So we got the toolkit here We open that bad boy up and we got a power cord a power brick classic This out of curiosity 24 volt nice We got a bag of uh allen wrenches and some screws we'll set that over here We got the usb filters gloves a spatula for metal spatula plastic spatula and everybody's friends these days masks Get all this stuff over here I think I thought that blew something off also. Hey, it looks like we have a Very fancy Nipper That's that's a joke But it's the same one's creality uses it looks like But I always like those you gotta you gotta take all the nippers you can get right These things are awesome for everything. It'll be cool to translucent an rgb inside What are we talking about builders mark? Uh, oh a pooch rock. Yeah translucent pooch rock with rgb inside. I like it All right, so we'll pop this bad boy out So there you go Let's see There's that I'm gonna check the box nothing else inside me if you want a cooler. We could put a cooler in there and boom shakalaga Unboxed ta-da. We're done. Have a great day. No Apparently it's not going to be a real interview real review till he talks about his favorite cheeseburger I don't know what you mean by that but I'm in I'm in Still waiting on mine to arrive. All right You're uh mars 3 You're waiting on a mars 3 to arrive. That's cool Um crystal salt Yes, yes, I love that idea like a crystal salt lamp. Andrew s. How are you man? Easily achieved rgb. Yes I think that could be pretty easy a hollowed You know what? I wonder if I could do the pooch rock in on this fabulous mars 3 here hollowed You know and then just put some good-sized holes in the bottom and throw your Rgb. You could do like string lights inside of it. That would be cool, huh? all right Yeah, I can go to lunch now Perfect. It's done. We're done. No So this is the cover And it is very nicely protected by the plastic wrap as you can see Got lots of light going on here today Flowing eyes that's there. Yeah, you could do that easy So let me just Wow, I love this red by the way cheap dollar store tea light. Perfect. Yeah. Yeah, that'd be perfect. You could do that boom Man, this this cover is very sleek Oh, I get I love the color red there That they used Pop this plastic off We got some nice foam around Uh holding your your gantry and your plate here Just a cheap. Yeah dollar store keep going. Yes. I can get lunch now. So, uh, this is The plate here Standard Elgu With plastic here So just for you guys Oh, yeah I don't have to get used to that top down camera. Boom That was for you guys Jerry, how are you? Take the top off more foam foam and more foam Looks like a Oh, we got more here here More here Let's see if I can Ready? Oh, yeah. Oh, yeah rocking it Is there any other streams going on today? I didn't even look I should have looked probably Bernie Sanders. Whoa Couldn't see a huge difference in the print quality over the mars pro and mars 2 pro josh says I don't have Oh, I do have a mars pro back there. I'll have to check it. I have a mars pro hiding in the back there I'll have to uh, see I don't know if you just saw my sweet hair flip there on accident Um, all right, let's pop out this instruction manual. Let's walk through it To get this test print going and then we're going to open up the next box Two boxes for the price of one today, right? Um Boom. Oh, yeah Yeah, I like it Still want one though. Nice Once again, let me know in the chat what you guys are drinking. I'm drinking the bubbly Lime it is so good Dewit 6 p.m. Nice Must be someone streaming at 6 p.m. Cool Hopefully no one's streaming now Last night I put the stream together like at 11 30 I should have done it earlier. So this week's this next week's stream will be set out way earlier So you guys know when it's coming. We have some cool. We have a video this week Uh coming on this back here That's gonna be cool finished my third cup of coffee. I need another cup. I got water though I got water PayPal 10 bucks Thank you so much mark. I really appreciate that $10 to the pay pals. Thank you. Thank you. Thank you. I do I really do appreciate that That helps the channel very greatly Just like going in coming a member you can become a member anytime on the channel We uh, we're gonna do some fun stuff. We had a member only chat last Last month we're gonna do another one. Uh, maybe maybe this week. Um this weekend Not this weekend next weekend technically is shot because I got uh weddings all weekend I have to do but uh this week i'm gonna stream During the week at night. So we're gonna do that Making coffee andrew s lemon la croix. All right I love it strawberry smoothie. Love it Bailey's and coffee. I need that. Okay So in case you guys need to know this has a three and a half inch touchscreen right here Uh, it is usb. You be uv photo curing um build volume is 5.64 inches long 3.52 inches wide and six and a half inches tall. Thanks for the Translation there it weighs about 11 and a half pounds We'll start right here. All right says take out the printer carefully check Take off the plastic wrap check I'm gonna bring this here. Let's see if I do this. What do you see? Okay, okay Should do it the other way, huh? That's what I should do but So what i'm gonna do quick here Is just plug this bad boy in now. I didn't uh before the stream. I was running around and I did not get My my side camera up So I messed that up So I don't have like a little a little close up side camera Because I was putting together the top down camera, which I really want to play with and it's gonna come in handy tomorrow. Caleb What is up, man? Wake up Welcome to the stream. Caleb You know where I am if you want to find me Or how to log in at least Uh, let's see cinnamon swirl coffee. Mmm. That sounds good a and w root beer. That's awesome a red bowl Smash that like button Someone can approve that whoever's uh Admin on the channel there. Oh, yeah So like I said, we have I'm gonna throw this way over here 24 volt um I wonder if I can change I gotta be able to change that I bet you I can I won't mess with it during the stream But for uh for the next one I'm gonna change that up so I can do like my front cam with the top down in the corner What? Oh, you don't have to I was just saying if you wanted to you know where to find me Caleb's in the house blastos here. What up blasto? I still got to get with you, man We need to do that project we talked about Matter of fact, I'm using the device here that I was talking about um for that project All right, please. Uh, let's see. Yeah. Yeah. Take all the plastic off turn on the printer So So I'm assuming I'm going to take this this uh vat out here and take off the Plastic underneath it before we do anything So these are loose Loose here so they all come out There is um on the bottom here You know what I'll turn this like this so you can see it You can see the vat. Um, there's plastic that you probably need to peel and there's actually these uh right there You can see it by my thumb on each corner. There's a bolt that sticks out And those bolts actually go into here Into each one of these to lock the vat in place. I love that by the way Brian vines. What is up? He's gonna be on in two weeks. Man We got just a Band of misfits today So I got that one off Peel this. Yeah. Oh, wait, wait, wait Oh, yeah, that was for you guys Now one thing I do see that I kind of like Is these uh bolts here stick down farther than the vat do so when you set this down It's raising up that feb from touching the bottom just a little bit just a little bit But it's off the table and I like that a lot. I like that a lot 3d print newbie milan. How are you? All right, so I got that done Man that light is killer, huh? Let's see if I can slide this over there. There we go I don't know. We'll do it like that for now for now Whoa, whoa Smooth. Yeah smooth criminal. What all right plug it in Um turn the printer on Not on There we go. We're on now I'm very sad. I don't have my other screen, but you can kind of see the screen is on there Or my other camera tomorrow. I'll have that I promise Is that really pink? Or is that a trick with the light? This um, no, it's like a red Let's see Yeah, this is like a deep red. I love it And this is like, um Kind of a pink I guess So I don't know what color you call that We'll call it pink. I like pink. Here we go Steven pool. What's up? $20 bret littlewood. Thank you so much, man Brett and buck king guppy designs. Hey, you guys are awesome I have I have a package of goodies from you guys sitting right there And I get to play and do some videos. Thank you guys so much. Look at that Anybody for some tacos? It's taco time Thank you so much guys. I really appreciate it. I love your products My or two are sitting right here. The pro is in the enclosure And I have a lot of stuff a lot of stuff to film. I love it. It's got some stuff coming Uh, uh, oh Shane says, uh, oh angry sticky tacos. Yes Uh, too funny. Okay. What do we got next insert to before turn the knob check Remove the tank check So I need to raise this up We're gonna go 10 raise We're gonna raise this bad boy up I love that. Uh taco bell's flatbread. I didn't I didn't even know that was a thing yet There's that one if someone becomes a member today, you'll see a different one too So the tacos anybody who donates you'll see tacos unless you shoot me a paypal Then I'll call you out right here. And again, thank you so much to mark for 10 bucks on paypal Whoo, brian vines. Uh while you're here. I'm actually using just so you know my road wireless go-to system And uh, how it works with live streaming is you can actually plug the receiver which is right over here Uh in in a hub I have but you plug the receiver you turn it on you plug it straight into your computer You using usb c and it sees it as a usb mic it bypasses all the The crappy inputs for mics on on your computer and it sees it directly as a usb digital input And then you can use it like in stream yards or obs or whatever and you get awesome audio Hopefully I need to go on and actually I can plug this in and you can do all the settings when you plug it in I need to turn my gain down on this wireless pack a little bit But I have one in my cart. What a sticky taco Oh The wireless go yeah Caleb Yes Angry sticky tacos is a new band name. I love it. We're getting the band together Okay, so I'm going to raise this bad boy up I'm going to put this on Tighten it down. Let's make sure we're on there straight We're tightened down check Remove the resin tank check Uh, let's see Loosen the screws that would be these guys right here Um, how big is this thing? Oh, those are pretty big. I'll use the included allen wrench Tacos are not my thing. Hey, uh, that's okay You probably like something else that that some of us don't like right? All right, let me see what we got here You can kind of see it. I'm I apologize for not having that side cam Um, so what I'm going to do. Let's see if I can turn this there's a bolt here and a bolt here And I'm just going to loosen those maybe There we go Just so they're loose But not overly loose because you don't want to have to tighten them all the way back in forever so Just so they're loose. So this does its thing It's dang get it Thanks. Thank you so much for being a sponsor of today's stream Almost three and a half million Models you guys that is awesome And coax 3d you guys are awesome too. We really appreciate all the fun Filaments the new coax next recycled filament is actually really awesome. There's some of my Thing right there You didn't or you didn't get to read the message with the PayPal. Uh-oh You want me to let me just look I uh, I I always get leery online because when you know when I'm live because Sometimes people don't want me to read the message to the PayPal, right? Ha ha for some Oreos after the stream appreciate you. Thank you so much That is awesome So good So good that probably just triggered Caleb. He's he's having a heart attack right now He likes Oreos just not with water, you know um, all right check Remove the resin tank check Put a piece of a4 paper that I don't have under there, but I do have regular old newspaper I'm gonna grab a piece over here I'm gonna drop some stuff, you know, that's how I roll that's how I roll You guys uh, if you're watched the last If you watched the last couple of Um hot makes angus was on for makers muse the last two weeks. What'd you think? What did you guys think I love angus? He's he is awesome. He's so much fun Uh, we had a lot of fun with him during the stream a lot of fun with him after the stream I might try to make that a thing one of these times for members where we have like a member only after the stream thing for like 10 or 20 minutes with with some of these guys I bet I wonder if I could talk Andrew sink into that he probably had fun doing that So I just took a paper and I clearly ripped it in half terribly Very terribly. Yes angus is awesome makers muse pretty decent dude Caleb agreed agreed Um So I'm gonna um See Should be pretty close So I'm gonna drop this Should have just left it That's okay. I'm gonna drop that right there Send them a bottle I love it Move z-axis to zero Uh, okay Okay, I'm guessing that's what that button is We're gonna find out I'm not sure it's uh It's a button a little with two little arrows or something Yes The rants were so funny. He cannot stop. He can't stop smiling and you know what his rants like Really hits you in the heart, especially with the petg one if you love petg or you hate it, whatever 3d jeff. How are you? So once it's at zero like that I was I was correct in my assumption that that was the zero button Then it says when the bill form stops place one hand on it make sure it's in a central position And fasten it using the allen wrench Since tightening the screws changes the tightness when pulling out the a4 paper you need to calibrate the z-height Okay, so let's let's do what it says first I'm gonna hold this down Oops that's not the right way There we go Hold it down Tighten Um hold it down Tighten check check About the start of print awesome Brian vines you got to edit a video. I get it fine. I guess Have a good day, Brian. Thank you for popping in. We really appreciate it. Okay I want to get this stuff going. What do we got here? Uh, let's see To calibrate the height of the z slightly again, there's no so you need to uh go so there's No resistance only a few resistance when pulling it out So move it with point zero. So I'm going to click this to point zero And go up I would say that's pretty close There's no resistance or only a few resistance when pulling the paper out click to descend the z-axis Paper if paper cannot be pulled out Uh, the resistance is very high. You should click it up if the resistance can be pulled out Um with slight efforts then stop. Let's try it We're gonna call it right there That was about as good as they explained it. Let's see if I can I want to show you something here Let's see if you can see where my finger is here Maybe Come on focus There you go right here if there's no resistance with the Or only a few resistance then Okay, I just want to point it out only a few if you have a few resistance All right after that is complete set the z-axis position on the initial light of the project. Okay Uh, yep. Yep. Okay. Where do we do that at? See operations follow return Click set z equals zero So let me go back here set z equals zero confirm check check I confirmed it boom boom Star Wars, whoo. I don't know what you're talking about this Imperial scout camp baby troops 77 I could really I could really mess some people up right now. I could be like this is our sign No, no anybody got that. Let me know Resistance is fuel time. All right Uh, let's see press 10 then up Oh press Press 10 million says up 10 times. It'll go up 100 millimeters. Got it. Put the tank in Got it. So let's do it So, uh, let's let's go to manual 10 millimeters One two three four five six seven eight nine ten Now we're going up 10 millimeters. There you go. I'll let it lift for you the resistance So good so good gotta love the bubbly keep hydrated 3d jeff. Yes the imperial scout camp That was our uh That was our welcome Oh man I am totally crossing Can't be fans without uh, let's see. Can't can't we be fans of multiple shows without being mocked? All right. I forgot. Nope I was just saying I you know, I got to be fans of both shows I was just throwing it out there. It'd be funny that if you went to imperial scout camp and they were like, how you doing? Yeah, whatever illogical All right, we're up we're up 10. Hey look some grease Grease is the word I'm gonna spread that up there a little bit All right, so now I shall drop my Vat on here like that and it should sit in and it does Let me show you that So Again these grooves here match up with bolts underneath. You set it on there. It finds it Now locks it in place. I like it. I like that a lot Rick and Morty Yeah, don't cross the streams. Yeah Up 100. Yeah, exactly Okay, now we're tight check We are tight now what it wants us to do is next uh Test the lights. So what I'm gonna do before I do anything. I'm gonna take this off carefully I'm gonna set it very carefully upside down. No, I'm not like this I don't want to screw up my level Hang on just want to make sure there's nothing under here. Let me grab a microfiber I saw speckles. I don't want to see speckles All right, no speckles. There we go Especially because If you're not careful those speckles will puncture Puncture your FEP If they're like, uh, you know sawdust or a bolt or something thick, you know that that All right, where were we as I run it with a finger That's funny. All right, let's see We're gonna do an exposure test what I did is I took the plate off here so you guys can see the exposure test I'm gonna Turn it towards me so you guys can see it And then I'm gonna go back here exposure Um hit next So we should see oligoeficial and it looks good Now he pulls out the cloth. Yes Yeah, yeah, I I want to touch it with my finger first and then wipe it off with a cloth Andrew s I did that just for you just for you. All right. We saw that that worked Um, yep, and now we do a test print it looks like So we'll work on that I'm gonna turn it this way and uh Grab some resin kind of resin do I want to use today? What do we got? On my few full amount is in there Give me a second. I got to grab some resin You know because why not? I have I have some I haven't used yet that I want to check out maybe Of course It's locked in my resin cabinet. There are my filament cabinet over here And I have printers in front of it Isn't that what we all do, right? Where's that at? Clear. There we go elgu So i'm gonna use some elgu that I've had That was loud So this is official elgu resin How are we doing? What's up? Nice little shake. So what do we got here? This is maroon From elgu I found this on sale on amazon and I bought it Did the did the cool mini gym come out okay? Oh Kind of until I broke it um Oh Give me a minute. He's on the he's in the back corner here. I cured him But I broke the top of the guitar This is a big bottle. I got this on sale at amazon a while back um, it is elgu Or elgu resin There is a max line. I like that a lot So what i'm gonna do Or do I need to tweak it so what I saw was the the top of the guitar broke when I was getting um Because I because I was taking off supports and the little guitar strings um We're really cool, but they they broke too because I broke the top of the guitar builders mark. Yes shake shake shake So let me go back here Go back here Now let's uh give you one of these You ready look at that color That'll match the machine pretty much We're just gonna fill it up because we're gonna test this out pretty good here There we go. I went up to the max line No spilling resin good So a lot of bubbles it'll calm down It expired Hopefully mine doesn't expire This is a thousand gram bottle it says so Now what i'm gonna do is take this bad boy hold it on There we go now this build plate is bigger too than uh the mars 3 pro I can't see it looks like that has resin on I would pull it out and show you but This is a bigger build plate than those which is awesome They got a little bigger build area in here than the other ones with about a smaller machine or about the same size I like it five one kilogram on auto ship whoa Sarah johnson that is awesome nice cool So then what i'm going to do it says do a test print so I'm going to take this right here That comes with it we're going to pop that in um We're going to see what's on it. I'm really sad because I my side camera would have been perfect for this All right, let's go down Let's go up. Okay Um rook they have a rook the classic rook Let's do it We're going to do the rook And here we go This is where we pray that the level was right Five printers nice I have a lot what I the problem I have is Uh time to get out here and print so work um a baby And doing this uh channel takes up a lot of time and unfortunately I I don't print as much as I should or could even All right, we're down Interesting All right, here we go. So i'm going to cover this bad boy up I am going to slide it over very carefully like I should have done It's jim's fault. Yes, probably It's always my fault So i'm going to set this way over here I'm going to uh get rid of this All of the good stuff here Oh, if I can fall over that would be awesome Work always gets in the way of the hobby. Yeah, well, um The I I tend to print more for videos than anything And I should I I have some fun projects. I want to do I really do and I should just start playing in those But 100 yeah All right, here we go. So we got the red rooks going we cross our fingers that their settings will work with those I'm just going to pack This stuff back in for now because I'm going to unbox the other stuff while we're doing that Now we don't need that I want to keep all this stuff together with the machine Because I'm weird like that This goes over here Whoo round one done Look at that 45 minutes. We're printing. We even talked a while Printing or printing This Is that how you do it? I can't remember This is the mercury x bundle wash and cure Yes Dominic you're right on that. How are lg washing cures compared to the other brands? Honestly Probably very similar But we'll find out so I bought the really big anycubic one myself. I bought it myself on amazon Anycubic's not cool enough to send me one But that's okay So I picked it up and I use that one All the time now Matter of fact all of my IPA is in it. So if we use this one, I'm going to have to dump some out into here Or something we'll figure it out But speaking of projects Yes Working on you know what nice. All right, let's kick back over to here Boom shaka laka all right this is The mercury x bundle wash and cure While we're printing some rucks. I don't know how long that says it's going to take. Let me look We got foam everybody. Does that surprise anyone? Lots of foam Let's see two hours. What two hours? Didn't got time for that Yeah, I don't think they're out yet. Um Maybe I'm not sure to be honest off the look. I know Mars three you were able to pre-order. I think they're sold out of pre-orders right now But there's a link in the description below So we got a classic elugu There we go elugu instruction book Look at the I mean this thing is This is a work of art how it's all in here. Remember this is a wash And a cure station both in here Need a cappuccino with all that foam. Yes It might be assembly day All right, we're gonna pull this out first So if I pull that out What do we got here? This looks like the turntable for the cure station it is So we'll set that aside for now. That's close. All right Then this looks like everything else is all packed in the lid with a lot of foam You can see that I'm going to set that aside for now No more no more stuff good That means all this foam can go back in I'm going to have a foam party I should probably uh be careful with this because I'm going to send this to Caleb. I think That's what I'm going to do Caleb if you're still watching this is yours This combo Is yours All right, so this is the base of the It might be the base of both actually We'll see in a second here It has uv lights in it It has a turning Oh, look at that foam All right, so first thing I notice You can see them There's like grippy little dots and stuff On there and I'm assuming that Will help you raise it up off the bottom also Maybe grip it on There we go Shipping out end of august supposed to leave. What up matt? How are you? So that is that It's super white super bright So let's do this There we go. That is The wash tub We'll pull these more foam out more foam lots of foam We're foaming everybody The same maker who makes the anycubic wash and pierce station nice Same manufacturer. I think I'm assuming you mean And I'm assuming There's probably not a lot of people that make these. Yeah, and they just rebrand them and brand them for different um companies You guys haven't checked matt's channel out Akuma mods there. He does a lot of resin A lot It's all the good stuff. He's got the real big Frozen right now. That's phenomenal. That only takes a bajillion grams of resin each print My mega review tonight. Yeah, there you go garbage so That's the That's the top Fairly simple Set that over here This Yeah I bet all right We'll pop this open this is very similar to Another one I have sitting over here too Three saturns. I can assure you it takes a lot of resin. Yes, it does I understand that Pop that open Man, this white is killing me today with all this foam There we go Look at that So the rest of it is in here um Five doesn't even cut to the bottom of the vat of the mega. That's awesome So let me take these out. These are going to be our Towers there's a Little holder for your vat Here we go I can get 23 minis on one saturn. Nice Boone County fair. Nice Uh looks like power brick This is going to be the uh stirring For the wash station there the base of the wash station if I could talk English would be good Uh, there we go some stuff there and then If I can get it out Your your wash and cure here the rest of this has um Um There we go. I know you ain't get there. So this is the Great or the tray or the not really a tray is it it's more of a more of a great a basket. We'll call it a basket here we go and This is The wash tub you can see down there That spins with magnets so let me uh Send this over here. You can see this goes down in Or it doesn't What is going on? Oh Let's see if you can see this see this right here It's it's like bow to in Right here Can you see that? So the stuff the stuff wasn't fitting I don't know what you can do about that Because your your wash basket should be able to sit right in there But it doesn't go in there, right? Look at that That's why I was having a hard time getting it out it looks like it was uh like compressed See You can you can see it. Let's see you can see it like that see how it's bold like dished right here And same thing on this side Hot air gun and push the sides out. Yeah, I'm gonna I'm gonna have to do something because Yeah Pushing it by hand ain't gonna happen Later thanks for stopping by matt a bit of heat. Yeah, I'm gonna have to do that I'll have to heat it up and pop pop those out So I won't be using that today because I'm yeah maybe uh I don't something in here to force out the sides and then heat it But you can see see how that is bowed in so bad um That's not good to me I mean that I can't use that because I can't get the basket in here Without like forcing it I could there we go. I mean I I really pushed it Like that there we go. I mean technically I could use it even if it's bowed No, the box wasn't in the sun. It's been in my garage for weeks So There's that and then this just so you see This actually will sit down in here If it wasn't bowed so much and catch the lip Let me take this other one out so you can see that better It's not terrible. I can make it work. I can make it work So this should sit down in here And Catch this lip like that There we go So you can see how that caught the lip in there And then you take your your build plate your bigger build plates from like uh, for instance Your your bigger lg machine And then you can set the build plate right on top of this and it holds it in there and you can You can cure this or cure it. You can wash the stuff right on the build plate. So I you know, that's pretty cool um And then yeah with the basket in heat it up. I will I don't have my uh My heat gun is not handy right now But that's cool. I mean I Then what'll happen? Let me just do this so we can Show you might as well This here is the Open it up There we go. That's the base So There we go. It has a knob on the front right here There's a screen inside. We'll look at that in a minute and Just a knob on the front to to adjust it And then the screen pushes But what would happen is this would sit on this It kind of locks in it like that There's a magnet inside of here And when you turn it on it's it creates that magnetic force spins the little prop In the bottom there and that's what causes your parts to get washed So that's pretty nice. I really like the look of this too. It's very nice Very clean So yeah, what I'm going to do is push this down I don't think that's going to help with the basket in there because it's just kind of flexing in Let's say It's like flexing in the metal You know pushing in now one thing is it's tight. So there's that So that's good But i'm going to put all these parts in here for now and then Like you said, maybe i'll uh heat it up with some heat and we'll get it going. Yeah, I think I mean, especially sarah. I don't know how you're washing and curing right now, but I'm washing right on the build plate drop it in there with your uh Big ones and it would hold it right in so That's how it looks here You can see how the basket sits in there Pretty cool And then again, it just sits right on the top like that And you can see that when you heat it Uh, it will Oh, yeah, yeah, got it. We'll check it. We'll try it. We'll give it a try. So let's move on So i'm going to seal this one thing. I really like is that Uh, you can actually seal the top When the basket's in there So when you're washing you can seal this so it doesn't splash everywhere Which is awesome. It looks like it holds Uh, is you can read here 7 000 milliliters Which is great So i'm going to put that off to the side here Oops, there we go So i'm going to push this off to the side so you guys can see it A little better. Oh you I mean, I love the look of it. Hey, it's so blown out. I'm going to have to I should fix that um Drink time everybody stay hydrated A little better We're rocking and rolling on the print. I guess I could pause it And we could uh, see if there's anything on the vat I mean on the build plate It looks like a rocking on those times though. I don't know what the, uh Default on this rook is time wise But if it's any indication uncle jesse has this thing flying He did some videos on this put out his settings in this video And if you're on patreon you can dive into that further With uncle jesse, but uh, i'm going to check out his settings. Make sure i'm running this now They did send me um a year of of pro cheetah box Which is a whole another discussion for another day. I don't want to get into that here because That'll be an interesting one, but uh, so i'm gonna have to use that on this machine. I believe Um Seven liters of alcohol you can't drink. Yes So this is Let me take these both out and i'll show you Right now I take them off remove the supports wash individual pieces It isn't as streamlined as my mars 2 pro, which I just set the build plate and then remove nice Oh, wow andrew s. I hope you're okay, man so Uh, you can see here. These are your led uh uv pillars They just wanted to show Here we go You can see what they look like here. The leds are lined up that pillar It'll connect down there like that and there's two of those By four gallons of alcohol for seventy nine dollars on amazon last week six months. Nice i'm on the water just basic water because I ran out of bubbly so I'm going to look at this book real quick. I'm pretty sure what we're going to do Pull that back so you can read it still Is we're going to take these towers we're going to connect them down under and then Screw them in just like that Nice water washable resin. I haven't dove into that have not dove into water wash. I have some Uh, but I've never washed it with resin Or with water. I mean All right, here we go boom Mercury x bundle Oh, this is really cool too. So Let me see. Here we go instructions. I want to show you Where did I put that right here? Hopefully it runs down the slope. Yes Hopefully it doesn't no flooding. We don't want flooding Yeah, it keeps breaking on the smaller parts. I heard that a lot matt who was in here a little bit ago Uh, I'm pretty sure he's not a huge fan of water. Water washable resins. Um, so this is pretty cool This is a 24. I just want to make sure Oh, no, it's a 12 volt. I was wrong. This is a 12 volt Plug in here. Um, and then Let me do this See this it plugs in once and you plug both machines in with this So you set them next to each other you have uh, oops, you have one power And it runs both machines I I really like that. Um, if you're gonna have two machines I really like that idea. Uh, because then that only takes up one Outlet That's pretty cool. Nice work on that one lgoo all right So let me get out the It's a double-ender. Yeah, yeah, you have how are you? Yeah, I really do. I like that a lot. Um, call it, you know liking the small things or something, but Uh, sometimes that's what matters is the the small things You know just like link 182 set So it looks like we have a little allen wrench and some little Uh, let's see. Yep little allen screws. So I got this Handy dandy, uh kit here. Let me see if I show you Um, I found this I don't think I have an affiliate for it. Maybe if I do I'll put it in the link later in the stream later But um rjx hobby Comes with five of these drivers actually I think canadian maker project showed these off normally only four fit in here and there was like this divider A 3d printed divider that goes in here and holds them in place You take that divider out and I'll five fit in here everything from 0.15 up to 4.0 And uh, let's see if I can get you a better view. Yeah, just like that It's not a bad little set So I'm going to try them on this here. I've been playing with them lately guessing this is tiny Big gentle have a good one man. Good to see you. Thank you so much for swinging by It's going to be a 2.0. I bet Only because I grabbed one and a half. It wasn't big enough. I mean it was too small. Yeah, there we go 2.0 So then what we're going to do Is you can see the The connector right here right there um It's going to plug into the bottom here Only plugs in one direction. So that's good interesting Well Is there two? No, so there's actually two plugs in here Uh, which is interesting Let me see Let me see No, it just says plug it in. All right. We're just going to plug in the one that fits Which in this case is the bigger one here So i'm not sure why there's two But i'm going to go with it. So we'll plug it in. There's no other place to plug a smaller one in anywhere so That's okay push that down in there And then it looks like there's five screws. Let me get some of this crap out of our way here Slide this over Of course I knocked it over right There we go So it sits in like this. There's five screws that hold this in um Here we go get this out of the way Let's see. What's the best way to give you an angle here So I can still show it. No not that way Uh, we'll find out jeff hutchins. I'm imagining it will be because there we go now you can see more of them right here The second one is for a different array. Interesting. Nice. So these are Two here we go Just going to use this get them tightening down in there that worked out really good Worked out good carl fetton. How are you? So like I said, there's uh Five total They are a uh two point Around me. So I have two millimeter Oh, you know what? I just found out. I like these even better now Something I didn't notice The end spins right here Ha ha I love that now you can push pressure on it and spin it at the same time Love that I think The only goes one way there's little tabs And I probably could It might go in wrong we're going to find out in a minute when I plug it in Guess if we have smoke, there's uh, it's plugged in backwards, right? So I've been playing with a little rc boat lately too that's been fun Taking a tristan over to a park across the street. We have a little pond And I go man that white is blowing out, huh? so And I got a dig so this one only has one So that's interesting. We'll go with it Mars 2 pro nice So yeah, it has tabs. It only can go in One way. You know what? I see what's going on here. I was wrong The bottom of this one has both See that I should have paid attention That explains why there's two It doesn't say that in the operating manual. I'm looking at it here But I guess pay attention and you'll see it Oh, no andrew s You damaged the photon screen That's not good So this thing over here is humming away. It's cruising. I is virtually I mean, I have a lot of sound going on here. I'll turn everything off, but it's pretty quiet though I hope to check that out. All right. Let me pop this out So we were plugged in the correct way But just into the wrong one. So I need to plug in Little one here big one there. Let's see see man that I'll have to fix that white balance, but yeah So that explains it. That's why Don't make that mistake when you get yours. Well, you won't now because I already did for you. See There we go Now this one We'll screw down Who does not want to stay up? 3d jeff 3d jeff that's pretty funny Have a good day, man. Have a great sunday. Hopefully everybody else out there is doing good if there's storms be careful So anybody out there play games? I'm just curious because I just I just snagged an xbox series x yesterday I got a pretty good deal on it Full disclosure. It was used and I found it on Facebook marketplace. I went and met a guy who programs cncs for a living There's no downlight in this one, but there is an array Right here that i'll show you in a second. It's super hard to see with all these Let's see if I take this off Now you can't see it the the light above here is killing me So I might have to work on lights above to to drop them down, but Andress plays loads of games. I wish I did I have not played a game on my xbox ones in a long time But at the same time I saw an opportunity to snag an xbox series x Um And I jumped on it a guy bought it two months ago. I got the original receipt There we go. So i'm gonna spin this around Only one here only one here Boom we're plugged in the right direction Yo av uh, just a heads up we're plugged in the right direction Um Nice sports games nice Call of duty. I have not I I have not played anything I'm I used to be a huge gears of wars fan gears of wars fan if I could talk And I have uh gears five that I've never even well. I just played for the first time Two weeks ago actually so I loaded that up on the series x. I'm gonna play with that also um, I downloaded Uh microsoft flight simulator. I heard that's supposed to be pretty dang amazing Um pretty much like flying with google maps that you can fly anywhere Nice andrew s good point Good to point So i'm really digging these uh these bit drivers here I'm really liking this especially with that spin top on it I you know I need to Gears of war I I loved gears of war Um I played some assassin's creed back in the day Uh, where did I put that little bag? We got extra stuff. We don't want to lose it. Oh here we go Perfect. I saved it Microsoft flight simmers nice, but I play on pc with the xbox controller. So it's not so nice Love it Yeah, good. It's supposed to be pretty awesome on the series x. We're gonna find out. I haven't I haven't tried it yet I I set it all up yesterday quickly and I have not had time to play it yet Which is like Killing me right because I want to play anything. I want to see how it looks So there's that set again if anybody's interested. I'll find it I'll throw it in the link of this description Uh description of this video. I I really like Spin that around. I really like it so far. It's actually pretty tough Um, I love the ends. I love that that has a spin in the spin ends on them and there you go Cool next let me show you Let me show you, uh Let me show you this here. So this is the plate Everything sits on I'm gonna take that off briefly And I tried to show you there we go see all the little tabs at the like raised bumps see Um, and yeah, I get to play games my kids know they've beaten most of the time nice Chris I've been playing. Hey, it's nice. You like the series x. I have I literally haven't done anything with it I got it ready to go and that's it then I downloaded a couple games and the gears of war five As soon as I plugged it in It needed an update and it was a big one. So I let it fly and I haven't even touched it I haven't played it since so A fortnight master that's probably not gonna happen. I don't have time for that But it would be funny. So here's um Elgu we got the push button here again. This will turn your dial Um, this is what spins it and goes, you know spins the table around Uh, there is let's see Right here That is looks like four uv Uh led dials there lv lights um And then the sides have two Uh pillars here. So I you know what that covers a lot now It doesn't cover like the anycubic the big one behind me here has the part that flips down But uh, this one doesn't that's okay though because This one has the two pillars in the back And it has the one underneath so it'll kill our underneath. I really like that Gears of war five. I yeah, I need to play it I have it carl and I played it for the first time like two weeks ago. I got through But we just played it for a little bit. My brother came over. It was an awesome time I haven't I haven't played games with him in a long time. So we're hopefully gonna do that a little more lately um Yeah, so I paid for game pass yesterday I did a dollar to test for 30 days or whatever it is and then we'll try it out Uh, I I think it's going to be a lot of fun backwards compatibility. Um, that'll be really cool So there's operation machine maintenance Nice. So what let's do this while this is printing. Let's at least see this in action um and I'm gonna grab the power we have here Mirrored at top and bottom. That's a good question. Well, they can't have a mirrored bottom Because they have leds on the bottom that shine up and that wouldn't work Yeah, that's carl fettin. That's where I got the flight simulator. I saw it on game pass. I was like, yeah, download it I honestly, I can't wait to play it. Uh, if anyone out there has played it. I think someone said they did Um, let me know how it goes. I think you can go like anywhere in the world And it'll actually simulate the weather right now and stuff like that. It's really cool if I if I think um, I watched a video on youtube that you can actually Punch in your address get the coordinates like online and then drop them in the game and actually fly Right right by your house or something. That'll be a lot of fun Best beginners 3d printer in 2021. Whoo. That's a good question g ready 18 uh, man, i'm loving Enter 3v2 It depends what you need man. How how big of build surface Area do you need out big of build area? Do you need and how much money do you want to spend? That's a good question Let us know and we'll we'll help you out with that one. Um My dad makes the textured packs for true flight. Nice That's cool. It's an awesome game. Nice Hey, how are you from senegal cr10 smart? It is going decent. It's right here I got to play with it. It i'm having the I think i'm having similar Results as uh teaching tech did where it's funk funky with the leveling so I need to figure that out I it might be a firmware upgrade now. I just need to look into it deeper. Um Flight sim goes anywhere anytime any weather nice So let me how do I want to plug this in It might be a little bit chunky. Let's see if it stays So I got a power pack under the when I built this I got a power pack mounted underneath Or a power strip. I should say so there's two Flight sim nice. Gee you do a search for exactly what you typed. Yeah, you can there's a ton of videos out there It really all depends on budget and it depends on You know how much money you want to spend how big you're looking for If you're just trying to get into it cheap, uh, I mean all those things It's a big question. So I got them both plugged in here We're gonna someone asked if we can power them both So they're both plugged in Hmm. Oh, it's plugged in No, nothing well I got power here the power pack is lit up There we go tricky So to power it up you hold the power or you hold the button in And you heard a beep and you'll see it power up like that Just want to kind of do that man these I gotta tell you these look really nice You know, if you had them sitting next to each other like that It looks really slick. I love it. Yeah, the long press turns it on the long press. I'm gonna do that For effect. So, uh, if you're joining us This is the lgoo 3 The mars 3 and this is the mercury x washing cure Station the wash and the cure uh, it was sent to me by lgoo to check it out and Start testing it ahead of delivery So that's pretty fun. We're gonna be playing with it and tested I just took a little bit of time to get it unboxed a couple weeks here now But we're just checking it out. So I think what we're gonna do now Is I'm gonna spin this Give it some time Let's do like a minute. Let's just see what it looks like. I don't think it'll work Yeah, hear that It only works if the cover's on So if I drop the cover on boom Now we have lights If I drop to this camera Oh, you can't see nothing But there's uh the four lights we talked about is over here. That's why it's so blown out. Let's see if I can No, I can't so anyways two towers of lights and One on the bottom now I wonder if I have something over here Hmm I do I have something we can cure. So let me shut it off So just a tap of the button shuts it off Uh green light green uh green up lights. That's new Hello from germany. How are you? gotta wonder why The wash and cure are white and the printer's black. Yeah, good question I you know what though? I think they look really nice. They have that really nice blue Kind of a shiny Detail there that goes around The buttons are nice. It looks like if you could see the timer if I can add time to it You can kind of see it there adding time. So let's see. What's the least we can do? Can we do 30 seconds? We can So I'll hit that No, maybe not That's funny. So it was spinning in there and I can show you that Um, but I'm gonna take this off. But in the meantime, let's cure something. Why not? We have something to cure. Let's do it. Let me just grab a glove here So I printed um a test piggy thing On this printer here recently But I don't think I cured it yet. I'm gonna set this here actually I'm gonna set this. This is a pretty awesome piece. This is a Trent Risto Design this Let's see and I was doing some testing. Wow, I could not find that There we go. I was doing some testing. This one's cured, but I'm gonna throw it on there again Um, I really love this. This is awesome. So he sent me this file so I could play with it Really cool file. It's uh, I hollowed it out not there, but I hollowed it out inside too Nope, you know what? I lied. I didn't hollow this one out. This one's solid But what I want to do is cure the bottom area better. So I'm going to set it on there I'm going to set our little uh Piggy there We're going to go actually we can now you won't be able to see it because of the light. There we go We'll drop that on We'll throw the cover on Oh, let's see Let's do Actually just out of curiosity. Did they say Yeah, uh, it's it's definitely a bluish color through the yellow box that makes it looks greener more green Oh, let's see. There's cleaning time. Okay, great curing time For models diameters less than or equal to 30 millimeters They recommend uh, two minutes if the surface model is complex It's highly recommended to increase the time as appropriate All right, cool So let's see what I got on here just for the heck of it We'll go like that six minutes. There we go. Now you can actually see it working It's cool how it does cure the bottom. I do like that a lot actually I like that a lot And now while this is doing its thing. I'm going to move it over here This I'm going to move some kind of close to our camera Super green. I think it's just green because someone called it out the yellow You know the yellow uh plastic or acrylic they use Makes it look more green. I probably could hold my finger over the sensor or something and Try to make it fire out but we'll see so So here's this Now this is the wash station here um And you can see in the bottom of it is that um spinner So let's just crank up some time There we go I gotta say It's not spinning You guys see it there, right? Now it might need resistance it might need the The liquid in there To actually work right Yeah, I love that because you have to tip them over absolutely. I I do like that a lot too um Yes, under seven That's that's awesome Yeah, and you'd be like correct to drink break everybody. So, uh, i'm going to grab me some Water Let me uh do this Andrew s are you still with us? I think you're still with us I'm not gonna lie. I really like this combo. It looks really slick um I I really like that it Cures from the bottom up. I you can it's really hard to see through here, but here you go. Andrew. I broke Because i'm a i'm a dummy and I wasn't careful but I broke the Guitar but you can see let's see Come on focus down maybe There we go Mini gym came out really nice the guitar came out nice If it will focus on it I think it's not happy with that light down there There we go. Let's see You can see the strings Broke because I broke the guitar but There is all this support crap back there because I had it sitting like this I was printing it this way because of the guitar there But um, I also drained it or made it hollow but anyways Andrew s made a sick model and it has a guitar and it's really hard to see Let's see This thing should focus in here um You should focus you dummy There we go Right here. It's hard to see but that has the edge of tech logo on the guitar Which is sick It looks good though. The model looks good the guitar. I just broke it The strings are awesome on there. The detail is really awesome on this. Thank you. Thank you, Andrew Now I got to print it again. Maybe I'll print it again in this red on the mars 3 pro here And we'll check that out Let's put some liquid in here and see what it does Let's do it. So I all of currently all of my IPA is actually in this big one But I'm just gonna do this here. I just want to see if it actually, uh If it actually spins good while there's liquid in there Grab some paper towels Do a little cleanup. Why not? Oh, what time do we got here? We got about 30 minutes left So, um, we're actually gonna be We are going to be Fibre queuing tonight with uh my in-laws So I got to run around so Let's see There you go Look at that Much better That works much better with the, uh IPA in there You can see it reversed itself there So a lot of these will reverse themselves halfway through the cycle So they'll go forward, uh, and then turn around and reverse itself halfway through the cycle Yeah I mean, it's got a really really powerful, uh Spinner down there if I could talk today Yeah, looks good. That's how it works though. Ta-da So Yeah, that's how it works I mean, it looks like it's going to be good and powerful for the size of the bucket Um, we'll have to test it out more when I heat it up and And move the uh and get the sides plugged in. I think actually honestly I wouldn't have to if I don't want to um As far as popping these sides out. I'm just wondering how common that's going to be If if it was just the way it was packaged or what but You can see there The spinners in the bottom it moved a lot of uh IPA. I think when you get 7 000 milliliters in here if you ever filled it It should be powerful enough to actually move it I'm going to leave this off a little so that will evaporate out This one is The big one from anycubic. We won't talk about that one right now But that's what that one is Don't think I have anything on here I don't I'll have to get some stuff printing today and get get these things tested out better But what do you think what's your thoughts on the looks what's your thoughts on the functionality? We showed how they function a little bit as far as You know, basically long press to turn them on and off There we go. I just turned that one off Uh, and then you use the metal You can see it on this one better Use the metal here to add time There we go see time And then you hold the button again or you touch the button again to uh, you know to kick it off So that's awesome. Let's pull this out. So is there a strong order with that stuff? Yeah, IPA can have a strong order odor if I could talk it if you uh get your mouth up in there and You breathe it in Uh the resin it really depends on the resin and it really depends on your sensitivity to it Just looking at this real quick. There is not a It does not appear to have any Venomation inside the chamber here At all so there's not like a box some of them have a little filter that kind of thing. It does not appear. That's the case here On on the mars 3 So You know these got cured It looks good. I mean There we go. Yep Looks like the bottom got cured a little better on this one. I had some curling when I printed this, but Yeah, that's I mean, it's pretty cool. It spins it around like we saw and Cures it from the bottom make sure if you're gonna do something You know if you're gonna do that maybe keep something on the outside So it actually crosses over the top of those So it actually crosses over the top of those I might like to see those come in If you could you can't really come in too much further because of the let me show you what i'm talking about here um So right here, it's hard to see what the glare is where those leds are in the bottom And you'd want to make sure this you know your model's over the top of that So it goes over those leds, right? If you put it in the center here, you're not going to use those leds at all Because they will just it won't go over the top. So Um, let's test something. This is pretty heavy. I'm going to put it on there. Let's see if this plate wobbles Because it is definitely holding down that side of the plate Turn it off kick it on We'll turn it up. We hit the button now. Let's see what happens if I'm guessing that side of the plate will just kind of be dipped a little bit because it's by itself But it's pretty cool. I I really like The the little piggy here. This was a test print off another machine Came out nice secured good super cool little print there And honestly, I don't see I mean it you can definitely tell the plate is a little bit Catty wampus, but It's not going to hurt it and it'll actually just bring it closer to those outside Who is that going to hit it? Nope. They'll bring it closer to the outside leds as well, I suppose So that's good The thing is like right now in the center it really doesn't have anything it's not hitting anything It's interesting. I I like the idea of it being on the bottom um Interesting I might have to play around with that because if you think about it I'm going to take this off When this is spinning around when it gets to here if you keep it on the outside so it has to go over that, right? When it goes around it's probably good from like right here to like right here or something But right here in the back it's between the two And there's nothing under it. So really I don't think it's doing much there Now there's probably light scattering around in there It's probably helping That is not working is it crazy But I'll have to watch that maybe I'll do a big model and we'll see how it goes But I think it'll be fine. It doesn't it's not too much. Even though this is pretty heavy But I really think you'd have to put it on the outside to benefit from those bottom You know those bottom leds. So that's interesting one thing. I really liked we showed a minute ago It is powerful enough to power both of these at once with one cord I love that. I love the idea of only having to plug in one thing Trent, I don't know if you're watching But I love your model too. This this model is outstanding Boom. I don't think it's available. I think it's on his uh etsy or something. I think it's etsy. Yeah Eat one of those ring with wheels like the microwaves. There you go Yeah, Andrew has how's the storm going? So, let me know what do you guys think? What do you uh, what do you think of I'm going to leave this off? Like I said, so it helps evaporate Um, what's your thoughts? What do you see in you have any questions that I can help look for? I got about 20 minutes And uh, we'll check it out Um, I just want to test here Make sure I don't have any questions that way. I don't So yeah questions comments. You want me to look at anything? Um, Nice Reflective aluminum taped to the inside of the lid. Yeah, you could definitely do that You could actually use aluminum foil If you wanted to The tape would be easier not easier to get off but easier to put in Can you can you see the actual dimensions of the two machines? Sure? I can see them just fine Ah, just joking. You guys have some great questions. That brings me to this. Let's let's grab my keyboard and mouse here And let's go to their website And uh Check it out now Uh-oh Don't be careful Don't want to um, just what I'll do. We'll check power resume if I don't be careful Did I just unplug that? No, I almost thought I pulled the plug on the the printer. That would have been funny there I like that you got that sarah um Whoa, whoa, whoa Let me pull it up Elgu Watch and cure Uh, we're gonna call this mercury mercury x Priota Let me drop this over here Share my screen boom shaka laka So you can see this right here Uh, thank you so much things and co-ex for sponsoring Today, I really appreciate it I'm gonna turn that off just for a minute So this is right from Elgu's site Looks like $150 for the combo And it is a good size. So if you have one of the bigger machines, it will work We're just gonna scroll down and check it out it is the Apparently they say the tank will hold 8,000 milliliters it has 7,000 milliliters on the marking so you I guess you could put more in Um There's some videos here How it rotates nicely shot Let's see if I can um find a Let's see works with all sorts of resin printers covering the elagu Mars and Saturn series Large water wheel 360 I was seeing if maybe they gave us the actual measurements because that was a question, right? Let me go back up to tech specs here Here we go So machine size is 255 by 155 by 385 total The wash volume Without a platform is 180 by 121 by 153 With I'm sorry. That's with the platform without the platform Which I'm guessing you mean it means to build plate platform Is a 201 by 124 by 255 so pretty dang big the What do we got here? The machine size for the cure is 246 by 230 by 363 The curing size here we go is 200 by 260 So that's pretty good size That is a pretty good size Let me just check any questions Let me pull that down for How much are they 150 bucks it looks like? Um g ready. Thank you. Nice to see you. Thanks for stopping by Test print is good Of the cool gym. I'll get it up on things If I didn't break it, it would be great. So I think so do it That'd be fun If what I'll do too is maybe I'll print one in the red when this is done and see how it goes um Would this be recommended for a beginner if if Let me think about this I personally recommend a wash and cure station if you're going to get into this The reason is is it makes it so much easier. Sarah has a bunch of them. Hopefully she can attest to that um But this is is it specifically designed for the large volume machines Uh, there's one for small machines as well. Yes, there is But in my opinion, um Sarah I would go for the big one right away You're going to spend the money on a wash and cure station get the big one It will do the small sizes And you can if you ever scale up to the bigger ones, you don't have to buy another one. Um I think that's the best way to go. I have for I don't even know one two like four or five around here and um, I just use the big ones now. I don't do anything else Uh, I don't play with the little ones anymore. Just because I don't have to I don't have to I have The big one and you can do the small models in this And you can do the big models in this. So that's really cool. Um Then you don't have to buy it twice, uh, you know, I we could look on that site And let's go see but if you're going to get into it. I I highly suggest, um Doing a wash and cure station right away Otherwise, you're trying to do it with stuff you put together with a light and everything else. It's just Yeah, this makes life so much easier um Let me do this Let's pop open that website again I'm going to show you something. So this was 150 dollars on their site, okay We go to 3d printing cleaning cure series And we go the mercury plus Which I have over here is 120 dollars Okay that does Uh everything in in one right but It's 120 bucks and it's small. So Let me give you an idea So I have it right here And I'm going to switch the camera over in a second But I'm going to give you a good idea So Let me just pull this down Okay, let me move this over Take these models off so I don't break them Slide this over so you can see That's the size of the one we're talking about today This is the mercury x right here This Which you can't really see let's see if I can turn it. Okay, so this Is this mercury plus So This machine here is 120 dollars 30 dollars less And Um, I mean you can see if I take this back out There you go. This will fit on here easily Okay The difference between these two plates As far as curing space goes I'm going to set this one on top of that one Let's see You see that That's the difference between these two machines Uh curing wise. So this is the mercury plus here This is the one we're playing with today the mercury x Uh, I really Really think I mean they connected a little different to this is magnetic here There's two little pins If I could get them lined up. There we go, but uh, honestly um I mean For for 30 dollars more Or 20 bucks more. What is it 100? 120 and 150 right So 30 bucks more And you get the giant Curing and a much larger Much larger wash two. So I mean for 30 bucks more There's honestly if you're going to get into this to start with the x don't even bother with this one This one is tiny Here's another example here. I need to clean out the resin. I let it sit out But this Is this sits on here. Okay, that's the wash tank for the mercury plus This is the wash tank for the mercury x Uh This We'll sit inside of here. I guarantee you if I take that tray out. This will fit right inside easily. So for 30 bucks Definitely get the mercury x don't waste your time on the little one Because as soon as you get into it and you love doing it You're going to upgrade your printer to something bigger because bigger is the fashion right now with these things I mean this one here is bigger This one's bigger Every you know, everybody's going much bigger. I have one coming It's a longer Printer. I don't know if it's out yet net. It's a smaller printer like this But that's I'm not really taking small ones anymore because people want to see the big ones now I really wanted to check this out. They this is supposed to be super fast 4k ultra hd all that stuff and and I can't wait to see what the prints look like but Honestly, washing cure wise go the big one right away get the X which is I keep forgetting mercury x The mercury x it's 30 bucks Do it it's not worth it to get this one Yeah, so sarah johnson has a huge point. I really like my Anycubic washing cure it's hiding back here. You can't see it. The problem with that is I have to take this tank off Put the plate on and then cure and then take the plate off put the tank back on to wash Um Yes Builders mark is 100 correct. So to give you an example is these set next to each other And you're done. You have two machines if one breaks you still have the other one. This sits on here I can wash in here take it off. Let it dry thoroughly You want to make sure your prints are dry before you cure them and then I can open this up Dry it on here while I'm washing something else That is phenomenal For instance this machine here I have the curing plate on here Okay, I have to take this off I have to put this one on Then cover it like that And then turn it on Wait for it to be done washing Right take this off Take this off Put this plate back on When my models are ready. I can put this back on and then I can cure. I only can do one at a time I wash or cure Sarah makes a huge point in this setup Which because she said that I might keep now I really like the the big format of the other one But I love how these look and I love that I can do both without messing with them So Caleb, I don't know if you're watching still But you might get the big anti-cubic Washing cure back there Instead of this one. I don't know yet. Either way you'll get one But I like that. That is a really good point Sarah Use your resin printers much more than I do and that will be a probably a huge benefit, right? A builder's mark again a hundred percent if you're if you're new to resin You got to be very patient. It's going to be frustrating in the beginning probably Cleaning the stuff if you if you have a failure and you have to clean it all out. That's a pain in the butt but With the clean feature. I love that now. You just throw an old support in there Hit the clean feature. It cures the bottom and you can peel all that out. I love that you can make your own Uncle Jesse. Oh, yeah, Uncle Jesse did a video on making your own Resin printing more difficult than filament absolutely So with filament you're done so say I print this Another design by Trent. Let me show you this up here Say I print this on fdm, right? This is a really cool print you put out there on Prusa printers. I don't know. I'm hoping you put it on things So prints like this on the build plate It he designed this himself kind of like chain mill when you take it out There you go. Now you have a basket and it sits in there really good But when you're done with this you're done You walk away When you're resin printing you have to take it off of your build plate You have to Clean it wash it like we're talking about here. You have to let it dry And then once you let it dry you have to cure it and when you you know There's like there's there's many more steps involved Now some will argue that you'll you know step Steps aside The the resolution is worth it if you're making minis like sarah It sounds like she makes a bunch of minis if you're making minis and these things are you know rocking and rolling uh honestly Resin's the way to go for that stuff because you can get your such more Resolution with resin printing I mean you can get some just phenomenal details. I I uh Um It is super hard to show you on that that mini gym with the guitar strings, but there's actual guitar strings, you know Hardly any colors matthew snugs. There is there's colors out there Uh, it's definitely not as abundant as fdm But there's some cool stuff um There is some really cool stuff like Excuse me Uh a kit that I have over here That you can mix your own colors and I'm going to be doing a video really soon on that I can't wait to do that. So you can mix your own colors There's a formula you can keep your colors if you mix them you keep that formula for later Or they have a ton of different formulas for all different colors you want to mix and use you know Basically uh anything I mean you can make make anything you want um Yes, sarah 100 agree paint all my minis anyway. So color doesn't matter good point most people Paint their minis so most people get done and then they paint everything that they a lot of things that they do Um, that's a really good point. How are we doing on time? We're pretty close here. Um So I printed this mini gym here. This is giant mini gym compared to 100% mini gym so I did this one on the printer that's over here, uh and It came out really cool. The detail is really good and all that and and a lot of people would take this and print it Uh printed paint it. I mean But there's really ups and downs on both If you're going for tiny miniatures that you want super high resolution detail This is your thing if you're going for like masks Some of the bigger printers are doing like full masks and stuff is phenomenal with a resin so it really there's The apples and oranges kind of uh, no Washing cure station from lu fit the prints of a frozen mighty. I do not believe It will so it of course it depends on the size of the print right if the size of the print fits inside of this Yes, um the problem is or the challenge is the frozen mighty is ginormous. Um The frozen mighty Or no wait, what am I thinking frozen mighty? You're good mega. I'm thinking the mega I apologize I stand corrected. Yes, so Mighty it mighty will fit Mega not so much. Let me just verify that while we're talking frozen sunny sonic When were you talking? mighty I'm pretty sure it's the same size as Yeah, that that will be fine um That will definitely work with these For sure now the big one I think it's the mega not so much Not so much if you do a full size print on the mega uh mega's two thousand dollars And Let's see No problem for the loot Yeah, the mega is a monster uh Same price If you check out the mega interesting enough, it's the same price as a phenom. I have a broken phenom sitting right over here um Let me look I want to say I have a stupid pop-up here. There we go It's a 15 a 15 inch mono lcd. Yeah Uh, that's not gonna fit if you do a full size print. It's not gonna fit um Yeah The mega is a monster Someday i'll do omega. Yeah me too Matt farmer has one. I had the opportunity they offered me to They offered an opportunity for me to purchase one at the Pre-sale price and I didn't do that. Um I did not do that I should have maybe I should have thought about it and I probably should have done it because it's awesome. Here we go All right guys, uh, I gotta get going pretty soon here. I got to do some shopping and get everything ready mostly because we have Finley coming over for barbecue Steven pool have a great day Real quick. Let's check this out. Um We are 52 done Let me get this crap out of our way here. We are 52 done And I think what i'm gonna do i'm gonna i'm gonna Pull the cover And i'm gonna pause it Let's just see how it's going So I pulled the cover here. I hit pause It should raise itself up And we should see how these rooks are looking Looking real good It's gonna be really hard for you to see though. I just realized I don't have that's the camera. I always have Um, but on the bright side everything's sticking to the build plate We're about halfway through the rook it looks like And it's super hard to see. You know what I'm gonna do. I want to try to give you a shot Get the shot, right? I'm gonna spin this around How about that? Not bad. You can kind of see it a little better, right? Uh So, yeah, that's the shot Now that is the shot too there we go. Hopefully I was in focus this whole time Just realized my focus was being silly so There we go. I'm gonna put the cover back on We're gonna let this fly and watch later today Uh, it looks like a couple hours here For the results on the twitters and probably facebook's and all that Um Yes, amen doesn't get better than that. The in-laws are coming over We're gonna do some barbecuing the little burgers and stuff and have a lot of fun Hopefully I wasn't at it. Let me know if I was crazy out of focus or something I just I just realized my focus was being silly It didn't look like I was but hey, you never know um Thanks for the show super helpful Need to clean off my wash and cure table to get it set up for when it arrives. Yes, you do right? I really I mean like I can't call this a review, right? It's an unboxing a checking out a using all that stuff But it's not a review because I haven't used them long enough to review it But I could tell you my initial thoughts are I really like the Uh look of them. I look the color After sarah mentioned it. I tell you what, um I really like the idea of having two separate machines Before I I love the idea of having one because it took up less space But to be honest if I'm curing I have to set the tub next to it anyway And then I'm taking up the same amount of space. So I might keep the setup I do like the idea of the Any cubic because it has the top, you know that folds down and you can Uh cure the top of your models. So we'll see Maybe I'll set them all up. I don't know But uh Burbers have not by req. Yeah. Well, I have a bunch of stuff. We're gonna throw on I did some jerky the other day Um jerky. I love jerky. I have a trigger Smoker a grill and that's what we're gonna cook on so it's gonna be a lot of fun But anyways sarah. Thanks for the ideas. I I love again the idea that I can cure while I'm washing something else That's great. Um You know I love it. We'll get you guys some pictures when this gets done. It looks like I got about halfway through Let's see how long did it say? Uh One hour five minutes So one hour five minutes away We'll get you a picture and I'm gonna in the meantime. I'm gonna play with the new cheetah box and um, I'll probably slice up a Sweet mini gym with the guitar courtesy of andrew s and we'll get that as the next print on here We'll get that flying. So everybody else. Thank you guys so much for coming. I know It's sunday. You didn't have to hang out, but you did. I appreciate it. We will see you this week I'm gonna do a stream uh later night One of the nights coming up this week. I have too many Uh printers over here not not getting any love so we need to get them out and unboxed Uh any questions? Let me know in the chat Also in the comments below if there's anything else I can do any questions I can Answer let me know as well Everybody have a great night. I really appreciate you hanging out with me members. Thank you so much for being members I really appreciated anybody who donated today. Thank you guys you rock as well And everybody else have a great day everybody. We'll see you tomorrow night on hot makes don't miss that show It's going to be a lot of fun. Bye everybody