 Hey everyone Shaper 1000 here today We've got a storm coming but I wanted to show this to you and I wanted to check it out See if the motor is going to work on it and talk a little bit about this thing, but I don't know how much time I've got Yeah, we got one rolling in so anyway Let's talk about this a little bit and I'll tell you about the story on this of How I got it Sorry for the thunder and the wind but We got this when I got the tires and wheels for my old John Deere, so I got these I'm not sure exactly what size my tires are I had them wrote down, but I Can't remember, but I do know there are twelves the same guy had it Now he had 15 on it and I was looking at it and he said you interested in that and I said yeah, sure him I was gonna give him the 15. He said well since you bought the wheels and tires Give me ten dollars. You can have that He said it does run, but somebody Supposed to have a sanding desk on here and a table like a tool rest with you know like a miter He said someone took that stuff off, but on the end of this it doesn't look like it's long enough to have that You know to put another Attachment on here, so I'm thinking this pulley might be turned around backwards I'll show you the numbers on this thing And I found one that was identical to it, but it was in very bad shape online it sold for ten dollars But it's the model number three five one point two two six one one zero There's an eighty three oh eight on it. I can't find anything So this is made in Taiwan, but I can't find anything about it Other than it is a Sears craftsman from the Sears Road buck company That's what the motor says I Don't know if the motors original it looks like And I can find a parts breakdown on this for every nut bolt washer these but they make nothing for this thing anymore But that looks to be the motor that belongs on it. It's supposed to have a one-third horse That's 1725 So that's the RPM by the way So that's a motor that belongs on it I'm thinking it's original All the colors match He said the motor does run so what I'm going to do is we're going to take this cover off So nothing's hitting or anything like that. It feels kind of hard to turn So let me get you in the stand. Let's get these two screws out. Let's get this cover off Let's see what's going on inside of here. Okay. Let's take these out there Phillips screwdrivers Now it's supposed to be vintage and I think it is But I don't know how vintage my guess would be 80s I found similar ones Different model numbers, but they were they were similar to this and they're coming up mid-80s I'm pretty sure it's not back in the 70s. I'm I'm guessing mid-80s right in there So what I think I Think This Turn you're out here this Pully here. I think needs to be turned around and That'll give me more room to put something in there So we're going to plug it in yeah, and it looks like That needs to be moved over It looks like this pulley here can be pushed back a little bit and that'll probably give me my The room I need to put My sanding disc on here as you can see right there This was on there. It was rubbing this it was rubbing this pulley So this pulley needs to be moved back, and I think this one needs to be turned around So it is miss I'd love to get it Get it complete, but I cannot find I think this would be a six inch I Can't find anybody that's got parts for this thing So I've looked everywhere like I said I found one that was identical and it was in bad shape It was missing rollers and stuff. It's sold for ten bucks It did have a motor on it, but the cord was all you could tell it'd been well used So we're going to plug this in I Don't know where on and off is on it Okay, I see it. It's off plug this in Let's turn it on I Can also see the belt. It's kind of rubbing on This tool rest bracket here, but that's right Now the sanding belt I can get no problem. That's not an issue. They're readily available and they're reasonable So I don't know I just don't know guys it Where I can get that Yeah, I'm pretty sure this needs to be turned around and this needs to be scooted back because that's You know, it shouldn't be this shouldn't be sticking out further than the shaft So there's a couple set screws here my guess is someone changed the belt at one time and Did it that way instead of moving the motor so my guess would be That's what's going on with it Yeah, because I can look down here and it's going down like this and then over that way so Man the storm coming in I want to go get a couple Sorry, I want to go get a couple tools and pull these off of here and spin them around Because it's not supposed to be out that far You know blow it out with some compressed air Yeah, it's So it's not complete, but it's in really good condition Very very good condition. It's used, but it's not beat up. It's not Looks like this has been rubbing a little bit Yeah, there is There is a little play there, but I can get these bearings the rest of them feel good rest of the bearings feel good and this is You know, you just push this down put your belt on lift it up. I'm not sure what size belt it is either It doesn't look like a 40 or anything like that But I guess Yeah, this it could use bearings in here Motor feels pretty good I'm not sure Looks like it might be a Try to get some of that dust out of there Yeah, I think it's I think it's a regular Allen head. Let me go get a couple of Allen heads. Let's pull this off Let's spin it around and see if that's better and see how much more room we got on this shaft Down here. Wow. Let's get ready to dump down, but This one here is loose. Now, let's check see if this one's loose I wasn't real tight, but it wasn't loose like the other one. All right, so I See Some marks over here on this arbor on the shaft I see some marks right there and I also see some here where it's been tight in there, but I think It's supposed to be up in here But it still doesn't look like it's going to Wait a minute had the wrong one So what I think I just think someone's put this on backwards All right, you know what? Let me let me get this back off of here I'll turn it on and use a piece of sandpaper and clean that shaft up there. Okay Go ahead and turn this on A lot of stuff up here right on switcher here and it's on a plastic table. Okay Now let's get this foot on here. There's a little oil you push a little plug out. You ignore these up There's usually one on the front one on the back Not seeing one on the back, but anyway Yeah, now see I think These are actually someone took this off and they thought that's where this one went, but I think That's where The one for the sanding disc goes So I'm gonna put it right about there Just til it's on the flat spot Hate when people pull these things apart like that, you know Now this one You can see it was rubbing there So I'm gonna put it it in too Like I say I can get I can get Bearings that'll work in that Same way as this if I can find I Can fabricate something, you know, so What I probably should have did was Put it on the way I took it off Like that Like this let me back out so so you can see kind of what's going on Started pull back just a little bit there so I think Yeah, this has adjustment on it So I can move this out some more. I don't know is there any nuts on the bottom But this one this can be pulled out a little bit more And that's that straight as an arrow down through there now So Yeah, I can see where it was rubbing on there Go ahead and tighten these up We'll turn it on real quick Yeah, see that's in there good ways now. There's no way There's no way that that pulley there can rub this All right, let's turn it on real quick Very nice. So all I got to do is move this tool rest out starting to rain Let's get these screws back in here Let's get one screw back in there it is. All right, we'll get these screws back in here So I don't know I Spent Wednesday night It's a Friday Wednesday night. I Spent two hours on the internet trying to Come up with what year this might be and I got on a website that had a whole bunch I'm like 222 of these things with what year they were and All the specs on it and But they didn't have this model number So I'm guessing 80s if you guys know, please Put it down in the box below Yeah, see then then I can slide this out a little bit more. I can make a I think I can make Make a tool rest fabricate a tool rest for it. This needs to be adjusted A little tap and it's just that belt right down here rubbing on this tool tool rest Bracket, I guess you call it Like I said That one was rubbing here, but this could be Looks like it's got a little bend to it so a little bit straightening, you know, these things get banged around in the You know in your work shed and whatnot I would adjust this right now, but it's starting to rain. So Okay, guys, there you go I just wanted to share that with you and if you guys have any idea of How I can get some information on this Now I'm not calling Sears But yeah, please let me know because I would like to get it This would be handy be real handy to have that But I mean this this is why I mainly bought it was for this part of for the belt sander part itself For sharpening chisels and whatnot This would be really handy too. I got to get you out of the ring. So anyway guys, thanks for watching. I appreciate it Monkey I'd take her mom to the doctor like she said and then I got to take myself. So she's Her mom's got a doctor's appointment, which is probably over now or maybe it wasn't Yeah, it's probably over now Yeah, so and then she's got to go to Ocala If you guys down here in Florida, you probably know where it is central central Florida To go to her appointment. So I've got a roast in the crock pot So it'll be ready when they get here. Anyway guys, thanks for watching Please let me know if you know anything about them things or if you know where I can get parts for it We greatly appreciate it. Have a great weekend everyone. Stay safe. Have a great time. Enjoy your life Shea butter the myth man legend gone for now We'll see you guys in the next one. Bye. Bye and take care