 floor insulation 1500 bricks two tonne of sand 200 fibrolytes 37 Newton and Trent's block Right, it's Sunday morning, it's the 18th, I think, October First house in the concrete Jason's doing his proud there, got that sorted out for us Good morning. Yeah, it's me. I'm back Sunday morning, it's the 18th, I think, October First house in the concrete Jason's doing his proud there, got that sorted out for us I had to pay for it, I was getting out of the car park at the airport Yeah, we've just got back from the trip away, which is absolutely horrendous Won't be going there again That would be a terrible time, but that's another story So at the moment, everything's here I did ask if I would put the stickers far at the drive as possible so they put everything at the bottom of the drive Floor insulation 1500 bricks two tonne of sand 200 fibrolytes 37 Newton and Trent's block So all that here should have been here and then the bricks should have been up behind them and the insulation so everything's back to front So, customer can't get the car on We're governed by the shared drive So we've got this massive area at the top here with nothing in it because the insulation has just been flipped over The radio's just packed up It was working a second ago, not any working now So as of now, we've got no power I might as well just get the Trent's block loaded in for now and see how we get on after that and get the four inch block in and we'll need some browns for that end because that's where the door is because we'll have to do the outside again for the slab Here, the plan today was to get everything up to DPC one Trentch one four inch inside three Facebook on the outside it's six to damp So first of all, get the water out then we've got the two thing to do up there we've got the cut out for the vertical DPC which we can do with the two thing on that side cut out here, all the tires to drill in and hopefully get all that done today and try and get a grab to bring us some stone tomorrow and hopefully we'll be able to reach where that insulation is hopefully and then we can just bring it straight in and don't want to get it in bags it's too expensive and it's too awkward it's so much easier to spade off the ground so yeah, that's it for now get back to you a bit Right that is dead our IP GoPro it's over nothing and you're one of them orders it's died this morning I managed to get a bit of footage and then it's just gone won't switch on so, pictures in trench block are loaded it's set out got our corners and it's all squared that's the diagonal 6519 so now, I'm going to try and get this first course of trench down once I've transferred the levels around as I said in the last video, the house isn't level but we've got to work off this end because of the toothers so we're going to work off there for the toothers for the level and for the bond you've got to be careful when you do toothers if you go down this end and set out your bond without checking it drive on it back you'll end up with a half in it and that's not good and it's not massive if we do because there's doors in the middle but you still don't want to be half a half of the wall if you can help it just a bit of forward planning, check setting out got the bricks on the map one pack's very wet so, I'm going to try as best I can to record on the phone today and get it go pro-ordered tonight and hopefully it comes in time if you carry on recording yeah, that's it for now it's five to five and I've just collected all the stuff together to put away still on the GoPro back in the media mode switched it on to see what happens and it's come on so I've missed all day filming because of this damn bloody thing I don't know why it's not working, but it's back working again now so there you go, that's all done trenching all the block work done up to DPC so it's ready for slabbing facework up on the far end where the door is because you need that in for the flap, the slab not the slab, the slab if you do anything, basically it's over there, you end up with the slab so yeah that's basically ready for slabbing so we're going to see if we can get some stone tomorrow from Jane Apia, the grab wagon see what we can do so, got a bit more to left over corners up there I'm going to put a quick corner up here I'll just run these in use them up a lot of wet bricks over there quick finish off here I'll film the corner because I've not filmed anything else today I've just turned that stupid on the phone so I've filmed this and filmed this just so you've got something to watch so yeah, there you go up to DPC all ready for hardcore so we're all set up block work is level so we can gauge our brick work off the block work wait the bond out so we're level, we're square got our bond I'll have a corner on here so it's easy to get the profiles on when we start the brick work but tomorrow we'll be trying to get the stone and get this little back filled get around the edge of the stone as well so we've got somewhere to stand so yeah, that's it let's get this corner built and that's used up now so probably get the bottom course in maybe a couple extra so I'm going to get the line up now get this running get the old fixed bricks on nearly there wait a minute two, three, four, five brick short anyway it's time to tidy up and get home twenty past five so let's get tidied up we'll then brick in that side's finished joint is up hole's filled up corner ready for tomorrow if we do any brick work hopefully get some stone delivered tomorrow we'll see how the grad boys get on for us so yeah, time to go home see you tomorrow good morning yeah, it's me, I'm back we're back on the job testing, testing, one, two is it working? the screen says it is I'll hand you back to Alex see if we can get this to work on the GoPro GoPro? it's getting board locked out yeah, so where was I? Dad's got Dad got all the trench block in got the blocks in and got the door set out for this lab but unfortunately we can't get stone till tomorrow we can't really touch the inside yet so today we're going to try and get as many things set out as we can I'm going to get started getting the rest of the brick in Dad's going to grind out the vertical damp mix is in bricks are loaded out all you need to do is get a string string line load out and then should be ready to go that's the front side back it's going to be a window in the back solid wall and French door over here yeah Alex just got that side in we can't get stone till tomorrow so we're going to stone up today but everything's such last minute we've just come back of holiday and it's being Sunday-ish today I'm no room on the drive to put anything so it's Tuesday today so it's going to be next week before we get to slab it which has put us back a bit so what we're doing today is we're getting the brick work up level there's a door to go in here so we might just do the lintels while we're at it it's going to rain this afternoon I've got the trestles I might get them outside linteling 1.8 openings we're putting 2.1 concrete linteling both skins and I've just done the grinding here so the two then cut through and then all the halves are coming out and then we can still get a vertical damping then as well yeah so break time now right it's two o'clock what do we get done Alex got this side in as you can see down there it's hammered it down for a couple of hours it's only a joint in Bloodstone coming up with planks there's going to be wet spots I'm going to carry on the toothing now Alex is going to get this front in she's going to have to get herself some dry bricks because a lot of them are soaked I don't know why but planks are very good for covering up with save your wet ones for the bottom course yeah and then I'm just waiting to hear back about the stone for tomorrow so tomorrow we'll spend the whole day just getting it prepped so we're working now that was good for the full team for measurements but I've not got the wellies on there you go that's all for now catch you in a bit here we go we've jumped out while the wet main stock Alex has managed to level up he's just jointing up now some are soaked, some are dry so it's a bit difficult it might just be a wide brush job in there tomorrow we need to try and fill the holes up but uh Alex if you get the jointer where the holes are and prod you know it's filled with water if you prod it you might as well get the water to run down further down no no just make the holes bigger so it goes down into the next brick if you know what I mean the ruined face pin doesn't look too bad now it's jointed yeah well why brush it anyway yeah so Alex's got us leveled up and I've been okay yeah and I've had the crap job but it's done all the tools are out I'm nice to get them all done without any accidents that one there with the extra brick is the brick had a big chip in the corner of it so that's come out so yeah I've just realised our damp course doesn't go all the way through because it's only a it's only a nine inch grinder so what I'm gonna have to do is take the cavity out so the cavity runs through so I'm gonna get onto that now so um yeah we'll get that done now all the battery dies done so um too doubt and the cavity's open so you've got to continue his cavity into here and there's our ties so that's it jobs are good then that's the crap job out the way so we just need to get our stone tomorrow we'll have to ring up to see when that's coming Alex just cleaned the mixture out and he's filled all the holes up jointed up and watered down the cavity yeah so that's it I've got to switch off now before this camera switches itself off we can't switch it off today in case we can't switch it back on again yeah right it's twenty to five I know that because we've got to get on before five o'clock through our Covid tests I don't understand it all but we've got to do them before five o'clock today because it's two days after we came back from Paris I haven't got a clue but I'll just go along with it so yeah just fill the buckets up the rain's filled the trench up stone's coming tomorrow I don't know what time two things done brickworks all up to DPC profile holes are cut out ready for the profiles buttons up ready for the brickwork and DPC is in vertical DPC that's 150 damp that's why it's sticking out so far yeah that's what's for today tomorrow is stoning up and prepping for the slab there's our large ablate for the slab we've got the 19 mil stuff around the edge instead of cutting it like we usually do it's going to be a lot easier we're going to cut that 225 because we had a couple of comments saying cut it long enough so that the the horizontal slabs trap it in like that then you're sticking up and it's not falling over the place then so we're going to give that a whirl tomorrow so yeah that's us it'd be nice to get it slabs we can get it tidy get it all stoned up around the outside too and then we can get all in blocks and get them on the slab so they can get the drive back for it showing about the sand being down the bottom but it is what it is so yeah, catch ya later