 Hey guys, Shaper 1000 here. This is what we're gonna do today. We're gonna be taking this out, putting this new one in here. So, I gotta do some checking. I gotta get some glue and I have to get some PVC because I'm gonna have to cut some of this and then I'm gonna have to make it come up to that. So, first thing we're gonna do is cut that one out of there and we're gonna see what we need. Okay, I'm gonna try to do this without getting in your way too much. First thing we're gonna do is we're gonna cut it off here and I wish I had a better hacksaw blade. This one's cutting out an angle. Give me another blade while I'm out. There's a little bit of water in here, but everything's shut off. So, let's take this off here. Now, we'll have some water come out of the bottom of that, but that's okay. We don't need to worry about that. We're gonna shot here, about here. We should get some water out of this one. He's just gonna pick me up a new hacksaw too and I'll give it its final cut there and I'll show you what we're gonna do over here and it's higher there. So, I'm gonna have to bring this up and this one's gonna have to come straight across. I'm gonna have to cut it here. Whoops, sorry. Cut it here and run a 90 into it. So, I'm gonna have to get some straight piece of pipe. So, I'm gonna need 390s. One, two, three and some straight and a coupler or two and some glue. So, I'm gonna go right that down and then I'll sweat on my new camera. See, there's always a little bit left in there. Pump does work. I did kick the pump off for a second. It kicked right on so I didn't want it to pump. I think water start coming through there. So, the pump's awesome. Probably just gonna get me a new one of them instead of a blade, I don't know. But anyway, so let me make a list and then when I get back, I'm not gonna film all that stuff for you. When I get back, we'll go ahead and finish cutting this off. And we'll cut it off down there. We'll start putting it together. It's pretty self-explanatory. I mean, they do even give you some, they give you some thread tape, which that's good. You really only need it on the gauge, which your gauge is right in this box here. So, I had some thread tape out here. All right, so let me get a list made and I'm gonna head out and I'll be back with you guys for you. It'll just be a second, hang tight. Okay guys, this is what I did. I took this off of here. I'm going away with all this. I'm gonna put a new piece of pipe here and I'm gonna put a 90 here and a piece of pipe here. So, I'm going away with that and then I'm gonna put a 90 here straight into the pump. And this right here, I'm gonna put a 90 and I'm gonna come up wherever I need to be. And then a 90 into here, which it has these things. They got little seals that go in there. It'll go on like that. And then our 90 will pretty much butt up against this, but we'll have a piece of pipe in there. So, I bought all that. We're probably not gonna use it all, but also I want to do a review on this saw. Okay, but you'll have to watch the next video to check this saw out. So, I'm gonna put this back in there and get it set where I need it or close to it. And then we'll go from there. I'll have to take some measurements. I don't know if I have a tape measure with me, but if not, I can use this to measure. It's no big deal. Okay, so let me get you on the stand. Okay, gonna be something like that. As you can see, right there, we're gonna put a 90 and come up and then go over. And again, down there, we're just gonna come out there over and in. So, let me go ahead and let me get an idea of what I'm gonna need pipe-wise. So, I'm gonna cut it a little long. So, I'm looking about right there. So, I'm gonna cut this pipe off and we'll start putting this together. Okay, I think I measured, I think I needed seven inches for the first cut. And I'll just use this one to mark it with. I got a pin in there, but I think monkey's using it. So, as you can see, I do have a tape measure here. Thanks to Monkey. I'll be at a little funky looking, but hey, it's better than nothing, right? So, let's get the saw and let's start cutting this. See if I can get a straight cut. It's a little crooked, but that's me not the saw. So far, it works pretty good on this. So, what I gotta do now is I've gotta take some sandpaper and I'm gonna clean this off, which I did go buy some sandpaper. We'll get this all cleaned off. And we'll, once we clean it off, we'll go outside and we'll put it on. Okay guys, so let's just go ahead and clean this off here real quick. Just wanna, this end here, I'm gonna be putting up inside that rubber coupling or coupler, whatever you prefer. And now I'll have to do the same thing outside. I'll have to clean that one end before I put it in, but we'll get to that. That's putting farms on the course. Yeah, I kinda, I used to make such perfect straight cuts, but not anymore. So this is gonna have the rubber coupling, like this. So this doesn't really matter. This side is the end that's gonna be, it's gonna have the elbow on it. So, I'll tell you what, we'll go ahead and glue the elbow on in here. Because I can glue this elbow on here while we're in here. But the other one I'll have to go outside and glue it on. Because once you, once you glue these on, I'll show you, but you wanna turn them a quarter turn. And I got some primer and primer cleaner. All right, so I'm just gonna scuff that up a little bit. This is just 120 grit sandpaper, all right? Let me get an elbow and some glue, and I'll be right back with you. Okay guys, I actually had to use a piper and should get this damn lid off here. It's never been opened before. This is PVC pipe. It's, I think it's 280 psi. Yes, it's 280 psi. And it's PVC, but it's just, this is wall casing. So it's fine, it'll be fine for this. So let's go ahead and, this is our primer. Primer cleaner, it does bow. You gotta keep your back a little bit. I don't wanna get this stuff all over the camera or the tripod. Okay, wanna set this down. Now I'm gonna get inside the elbow too, get it cleaned up, or get it nice and, okay? Just like that. Same as with any plumbing. Now let's see if I can get this glue. It's just all purpose man. It's for PVC, CPVC, and ABS. So it's perfect for what I'm using here. And again, I can't get that open. I need to use these. And they've never been opened before brand new cans. Okay, so there we go. Now what I'm gonna do, okay, you wanna let that dry. I'm gonna put some around here. Just like this. And then put some on the inside of here. Just like this. Now, I'm gonna put these together like this. And give it a quarter turn. And it says to hold it 30 seconds. I'm not gonna bore you with that. So next cut will be outside. Okay, slight change of plans. I'm gonna head and take a couple of measurements. That way I can make a couple cuts in here where it's a little bit cooler. So first cut. It'll be seven and a half. I've already got it marked. Cut two. I decided to cut the other pieces off inside the garage because it's a little cooler. Still cars won't pass, of course, everywhere I film. I'm not getting the straightest cuts, but they'll be fine. Did you guys notice on the last one that I cut, I cleaned both ends and I only needed to clean one because it goes into rubber. So I just wondered how many of you guys caught that. Okay, so what I'm gonna do, I was eight and three quarters. I need a seven and a half piece here. So that's right on the end of that E and piece. Okay, let's cut this off. This was eight and three quarter. I forgot to hit the cord. Then we should be able to go back outside. So I'm gonna go ahead and cut this one off because it's pretty boring. If you get the idea, we have to cut pipe. So let me get this cut and then we'll go outside and start putting some things together. Okay guys, I don't know how much I got of this, but anyway, I went ahead and I glued this up the way I needed it to be. I was just going to fast forward it for you, but apparently I didn't hit record. So anyway, I've got it glued up. We're going to take this outside. We're going to put this one on and then we'll go up to the top part, which I'll probably have to do out there. We'll just have to see. But anyhow, let's take this out and let's put it on. We have rubber seal. We got to put it in here. I'll show you how to do that. Okay guys, now this is pretty simple. It's just a flat, looks like a black rubber band. And it's just going to put this right in here like this. There's only one way it can go, just like that. And that goes up against there. You don't have to put thread tape on here. This is what seals it. Thread tape is not going to help you any. And what that does, see how it sticks out there just a little bit? That goes up against it and it seals. So let's put this on. Okay guys, what I'm going to try to do is I'm going to try to put this on without getting in your way too bad. So let me get back in here. This is going to go down under here like this. And it's going to go into that rubber plate, which does not need glue. Okay, so I did away with one of them rubber couplers because it's less to have to worry about leaking, right? So I'm just pushing down on that pipe. Let's go ahead and put this on first. And you shouldn't have to tighten these up with a pipe wrench. It should just be able to be hand tightened, which is not tight yet, of course. But okay, I'm going to put this inside the rubber coupler over here. There we go. All right, now I'm going to tighten this down. And I'm going to tighten the rubber coupler down. I don't know if you can see because I've got the screen turned around on the camera. This just has clamps. Check the other one. Now, let me get out of here. Now you can see what we've done. We have come off of there. We've done away with this one. So we've come off of there. What that does is, let me get you off stand. I'll show you. This goes up on top of the house for a pool heater. But I guess one of them joints up there is leaking somewhere. So what it's going to do is these are off. This one's on. So it's going to come up and down. Actually, it's going to bring it out of here, out of there, through there, up to here, and then back down and here and then into the pool. Okay, so this is what we're going to be doing next. Okay, so I'm going to go ahead and get cut what I need to get cut. And I got some Justin doing this, apparently. It's not setting right. I'm going to go ahead and get cut what I need to get cut. And I'll glue that together. If I have any issues, I'll turn you back on. If not, say I'm just going to run two elbows. I'm going to run an elbow down here and an elbow like that. So this will have to cut. You know, of course, I'll have to cut that off some. So that's all I'm going to do there. I'll kick you back on when we start to pump up, make sure there's no leaks. Okay guys, we're getting ready to turn this on. The switch is right over here, right underneath that little thing there. Monkey's going to be filming. Now this is the first thing you want to do is you want to open this up like this until it clicks. It's a quarter turn. Water should flow steady out of here after about 30 seconds. So monkey, are you excited? Yeah, I'm excited. Let me go around here. I don't want to stand anywhere near that one. Why? Is it going to blow up? Oh, it shouldn't, but it said to stand clear. You ready? Well, what about me? Am I far enough? Yes. Can you see? Look through the screen. Yeah, I can see. Right now for about 30 seconds, we should see water coming out of that thing. Water where? We saw water. Okay, but I got a leak back here. So something ain't tight. Okay. Right here. It was leaking for some reason. All right, let me get that taken care of and we'll be back with you for or try two. Okay. All right, round two. I didn't have a seal in right when I was putting the seal in it kind of popped out. So now we got this open again so that bleeds the air out. We're going to flip the switch on and we're going to wait on water to come out of there. This seems to be good. Okay. Show monkey and yep. So it is running. Awesome. Let it go for a little bit. We're going to let it go. Make sure it's not going to start leaking. And then we'll get back to you and we get ready to leave. Yep. Okay. So monkey's putting stuff in the pool. Yeah. Still running. Let's go check this out here. Dry as a bone. Good pressure. No leaks. It does have a timer up here. I don't have it on the timer. We're just going to let it run for a couple of days and she can set the timer. She comes back on Saturday. She's putting pool bleach in. So yeah, it's running good. Yeah, it really is. You can see it going in through there where it's supposed to. And you can see it swirling around here. And she's going to put some tablets in there. So there we go. Mama, we got it working. Got it working. Yeah. The first time was just that little O-ring I showed you. And when I put it in there, it must have popped out a little bit. But she was like, oh please. I'm like, why are you praying? Well, because the motor could seize up. It's been over a year. Okay. But I told her though, the first thing I checked was the motor. It kicked on. Yeah. Thank God. So we're lucky. And then she's, oh please. No, you're not lucky. We are lucky because we have you to help us. Oh yeah, nice. God sent you to us. She ain't buried. The myth, the man alleged. I'm gone for now. Bye guys. Take care.