 So we're just going to take a little peek at what's on the inside of this now and I'm going to show you, first of all how easy it is just to get these props off. Just pull them off, you pull them off and push them on. Now there's one thing, ooh that's a very stiff prop. There's a little tool that you get with this to help get these off and of course I've lost it because but these things can be quite easy to use but no, mind what you need is a little go with a screwdriver or something with a bit of a flat end on it. It'd be nice to have the little hooky hooky thing but you can still get it off. Don't do it too far over on one side as you can just end up bending the pin in the middle of this, the motor shaft. That's very soft compared to that one but this one's a newer one. Or at least it feels like it, well maybe that is. So it feels very soft there. Again this one's a bit of a problem to get off so we're just going to have to get an eighth there and just get a little tiny bit of assistance. Now I've had to change a couple of props because I had mangled them up a bit. This one looks like this is starting to go on its way a little bit but nowhere near as bad as the other two. During this video I'm going to show you. Now this one's got a bunch of speakers and a bunch of screws underneath. Nothing underneath here, I'm hoping that I can just pull this out without messing around. So let's just get this open. Now this is my little favourite. It is just so much fun to fly around and getting the batteries, getting spare batteries for it is easy. I've Amazon, they've bought five of these with a 5-way charger for them, £15. And it's fantastic because one battery for playing with these is just not really enough. Not really enough. And you can fly this outside but you want a low wind if you can, you've only got two inch propellers. Well they might be slightly over two inches but they're not much bigger than two inches. An inch aside. I'm going to give you a bit of an indication to how small this thing is but it's tiny. But it's a fantastic little thing to fly. So let's pull this off. Now one of the things I'm really pleased about with this is, pull that off. Is how accessible everything is really. Just those four little screws and there's not a lot really to see in here. There's definitely one of those nothing to see here moments. Really, we've got a screw there and we're going to undo that now. I'll try not to damage anything. It's very easily accessible. Is it the same as the other ones? Yep, all the screws are the same, that's always a nice thing. I'm going to look on the other side of this. Well right, but I didn't expect to see that as an antenna there. That's our antenna. Right we've got our little barometer down here. Let's see if that's got a little pin hole in it. And this one I'm going to assume is the flight. Well, it is, I mean it is the flight controller. And you're going to have some little tiny transistors, little tiny MOSFETs I expect, for just powering the motors. There's some MOSFETs here. I'm going to assume that they're MOSFETs. Well I'm just going to say transistor because it's... I'm going to see if we can see something on here. Let's have a look. It looks like there's markings on there and like on the other one. It's a different form. Do the one here. You see that on the back? Let's have a look at what we've got. I need to look through both of these. Not quite enough magnification for me, just the one. P-A-N-1-6-3-C-X. Let's look that up. Okay, so we've got this Pan chip P-A-N-1-6-3-C-X. 2.4 gigs wireless transceiver microcontroller. All right, for more I can see on this. I'm going to let us go in the new bigger. No. What he gives you the layout here? He gives you all the pin-outs. Not the layouts, sorry, but the pin-out. What else have we got in here? O-W-3-7-E-7-E. You may not be able to find that sort of chip. I mean, it's such a tiny little board. Hardly anything on there, but this is... I mean, imagine that you could take this out of here and fix these to some lollipop sticks and direct yourself a little flying system. You know? It's crazy, isn't it? That's all there is really. And now one of the reasons why I really wanted to look at this was because of the motors. I can put that in there. I can stick a hole in it and have it popping out at the top. I'm not going to bother. But the motors, and the reason why I wanted to know these motors were going to be interchangeable with my Simer. Because when I first got my Simer, I expected to be getting through lots of motors and lots of years. And so, you know, I've got a bag of gears and all sorts of spares for my Simer. See where it is? There's quite a big bag as well. Full of stuff that I've never needed. I just bought it as a pack of spare stuff off eBay for the Simer. It's not to hand. But in there came motors. I bought lots of pairs of motors because that's what I thought I'd be getting through. But I've hardly got through any. And it's such a shame. But now, I've come to realise that these motors are the exact same thing. These motors are the exact same thing. The only difference is here. These are got this bit on. But you can take that off. That cock thing. I wouldn't throw it away because people would sell them. But this is the exact same motor. So I'm chuffed as punch. Because it means I've got issues with my motors already. I fly around a lot of time and they prop guards. I do hit things. This thing, when it hits something, will shoot off all over the place sometimes. So it's good to... Because the motors are going to get mashed up a bit. But it's just fantastic that I've got all these spares. Because that means this for me is a true winner. One, because of the spare thing. I know I'm going to be getting through motors at some stage. I did worry that maybe these were glued in or something. But fortunately they're not. One or two are very tight. But that's all right. I can work with that. I know that they'll still come out. Yeah, amazing. So these are where the little LEDs are then. So these will be the red LEDs at the back here. And these will be the white LEDs at the front. Which is another reason why I like this. Orientation is fantastic. It's exactly what you'd expect it to be. White at the front, red at the back. So the orientation is very easy to be able to see. I do like that. There are three settings on the remote. One of the crazy things about the remote is that it's so big compared to this. But these remote I don't like. They're like Xbox controllers. You don't get enough. You can take that off and try and put something on there. I did. I don't know what I've done with that probably. Chipped in the astray because it came off. But it was basically just trying to give it a stick. That won't actually fit on there because that hole is not big enough. Because it's not as easy. I mean if you're used to this sort of thing for an Xbox type thing, that's all really good for an Xbox and moving around low resolution. But you need something with a bit more controllability. Honestly, it's the stick thing you want. If you're going to get into this and you're going to get into your FBV, you're going to find your radio. And your receiving gear is going to be the stuff that, you know, whether it be a headset or a nice screen or something. It's going to be the stuff that you want to spend a bit of money on. You know, get your radio right because you want a lot of control. And the more intricate stuff you want, the more control you want. Like, you know, there's one thing from doing this to this. There's another thing from doing this to here. And then there's another from just holding it down at the bottom and doing very slight movements. But again, you know, I do mine a hybrid. So it just means I've got full. I think it's sort of like, you know, keep things where I want it to be and just move along and do. That's me, but that's the best way to do it. If you're going to get into this as a hobby FBV, you want sticks. When you look for your little, little fly around the home house thing because you want something like this, because flying around the house is going to give you the ability to just get all that hand to eye coordination. And in the relaxing, you get a whole bunch of, you know, I've got a five pack of these. Like I said, it came with a battery five pack of these. And this is going to give you plenty, you know, take a 10 minute break between flights because the motors are going to just get hotter and hotter and they'll burn out. And you don't want that. Just take a 10 minute break besides it's quite good. Get three of your batteries and you'll learn loads. You'll learn loads. This will fly in the night. I'm going to put this thing up on the screen here. I can't remember how long it runs for. So it's about a few minutes. What I do is I just chop this, put this in here. Welcome back. So there's just a little tiny bit of flying around like that. That's in and out of the windows. That's simple enough. You see it's got the guards on it and it bounces off a little tiny bit. So, well, there we go. Nice and easy. That frame has the battery holder built into it. I've seen these and you can pick these up very cheap. These little frames, but as you can see the whole thing. I'm sure that it's going to be very hard really, I would have thought to break this board. Because one of the things about the propellers is because they already slot on, there's going to be a certain amount of resistance. You're not going to have to, I doubt if it's going to burn out the motor so much. The propeller is more like it's spinning here. Be so much of a stress that it burns out the motor, which is another good thing. That's if it does work out like that. But if it does work out like that, that's a bonus in and of itself rather than burning out motors. And of course with these things now, unlike the Sima, which has got none of this button to take off, button to land, malarkey, or any of the barometer in it or anything like that, it's got none of that. And dang it would be wrong, it's still a great thing to fly but the more you can fly with just manual controls, no assistance, the better. It's always alright to have the assistance there but if you need it and you don't have it then you can find yourself in a bit of a tight spot. That's my thinking on it. That's why I always like to fly manual and I'm quite low, just because I know if I crash then. And I tend to when it's low, but if I crash then, I'm not going to say I'm just going to do minimal, minimal if any damage at all. I'm really struggling to get that in the hole, it seems to have a, there we go, a bit of a mind of its own, which has now been defeated, or at least, I thought it was, starting to think if that's actually got the hole there, or not, because I know it only had one in one and it's a good possibility that's going to come from there. There's no hole there, that does not have a hole, the actual hole itself there. I don't think, oh, it does have a hole. Let me just pull that over here. Does it have a hole or not? It does have a hole. And on the other side, does it have a hole or not? It does have a hole. That one looks like it's a deeper thing for the screw, so I've got a funny thing that's going to go in there. So let's try again. They're all the same size screws. Oh, and I'm sorry that I didn't so rebuild the other one, before people might think, oh, one of it still works, but yeah, it still works, nothing. Nothing wrong with it apart from its controller thing. There we go, I think that screw is in there now. Oh, no, it's not. What is this tin that's going to be quite difficult just to put it back in again? It's just getting into that little, it's that little hole. Seems to be afraid of me, here we go. I don't want to do it all too tight, because I don't want to break the thread on it. And these things, you know, it's just very thin, light plastics really, so it's going to be very easy to damage it. Just trying to see if we can get these. Wires aren't the way of the LED, so you've got nice clear visuals, because it really does help with orientation, especially flying line of sight, of course. Try and get it in as well in such a way that when I put the screws back in, it doesn't either trap the wire or get the screw to screw through the wire, because we don't want that. That's going to cause a problem. That could be the sort of thing that might damage, hopefully it's protected the board and that sort of thing. I'm just trying to get that out of the way there. I hope that's good to go, it should be near enough there. Now you've got to push underneath, and there's like little slots that that has to sort of slide into some bit of a conventional wire. And I'm just going to push it on the top and just push it down into it. I said I'm sorry, I had to put it in this time around the way it was. No, maybe it's not. It just seemed like it was being a bit more awkward. I'm just worried about the wires. So I'm just going to put those screws back in. I don't think it helps at this. It's got a magnetic tip. Then I'd hope that the one that came with it would have as well. This is the one that came with it. Try and see if anything can be a bit more behaved, but nope. It's just as a... I really do prefer this one. Really, really do. So we've got snow and stuff coming to my my area over the next day or two. Here comes the old winter. Yeah, on these bits, rather than, you know, if you're just going to put it on what you've got to be able to do is just pull up the arm a little bit and sort of like get that little tab thing to to slot in if you can. I think that one's gone in. Yeah. Otherwise it would just be sticking down I don't know what else. I mean, I've looked at lots of these little tiny micro drones and I don't know about you guys out there, but for in my home, all I want is something that I can't do any damage with. I've got a couple of cats and I don't want to start all those. Ow! I don't want to stab myself too much. Um, even though my one cat just doesn't care at all about a little, I'm sure if I put the the Simon on he'd be running off just like the other one runs off. Never crashed into it before but I can imagine the eyes a little bit weird from the screen is quite awkward. Doesn't know what I'm sort of looking through the screen a lot of the time trying to try to still see that they're all magnetized around that screwdriver head. Yes, that's what I'd like to say about this I reckon it's a cracking little flyer I use it on speed on inside the house it's definitely lively and you put it on speed 2 and speed 3 you get a lot more pitch and roll which of course that makes the whole thing a lot more nimble and best played would like that outside I would have thought just got one little one to go there it's a struggle magnetic at least it feels like that there's motors back down propels propellers back on now the front was white wasn't it and the the propellers are like on the normal quads like on the quads that we build behind us and stuff so it's very easy to get on that one and so yes the tops could face inside leave an edge in the and the bottom ones face the outside let's chuck this back in I presume it's going to be okay I've got a bunch of them ready to go now this there's actually jump up in there when you arm it so we're not supposed to do this we are going to we've got to clear above us so we're armed and we're ready to you see how those can go a bit nuts when you I'm glad they're kind of motor stuck to the motor and that's the only thing with them when they're doing something out of the ordinary you can expect it to and then start doing a bit a bit crazy but like I say it's so small so light the way it's lit up like on the front there look brilliant you can see it coming towards you you can see it going away and you can tell from a distance like from one room into the next room it's orientation which makes it absolutely great of course flying around the home isn't easy it's not something I mean it is but you're always going to have the fear of crashing or not the fear of crashing it's not easy but I suppose that's just part and parcel of it also there we go oh and I found out there's a button here this is that you can trigger it to do a what would you call it when it goes around itself like this yeah one of those maybe tomorrow I'll know we've got snow for the next couple of days 75 kilometer an hour winds so this isn't going to be going outside but we'll have to get around to showing that I've not even done it myself yet how that works I didn't know what this was I had to look in the manual because I kept doing that thing what else going on, what was going on and it cancelled as we were going to do that but I didn't know I didn't know what it was for but it's in the manual again anyway that's the end of that next one that's coming in is going to be interesting so we're getting on to the other stuff again okay catch you in the next one guys