 Shea Bear 1000 here today we're going to be trying to put these rollers one on each side onto this trailer so the boat will load easier. There'll be some fabrication involved in this and the number one tool that you're going to be using is up here because there's so many different ways these can these can be put on. I'll show you how I'm going to do this one but you know you got to use your mind and try to figure out how it's going to be so stick around let's see if we can get these put on today. So I've been looking at this and if I put you know that boat's going to have to come out there it's no biggie if I put these here they're going to be a little too high so I think what I'm going to do is I'm going to have to move the rollers down a little bit to match my boat so what that's going to involve is just taking these bolts out these two bolts I can't see what you guys are seeing there that bolt and that bolt out and I'll lure this down where I need it to be I'll mark it and then drill two more holes and bolt these on where I have to have them so first thing I gotta do is get that bolt out there there's one on the other side what that wasn't one time there was like an eye here and you'd hook something to to tie your boat off or you know to strap your boat onto the trailer so which I just usually come around the back like I said this is not the right trailer for this for this boat so I'll have to I need to eventually extend the boat out or extend the trailer at least 18 inches I think 18 inches will put me where I need to be on it so I gotta get that bolt out and do some measuring and I think once I lower that that roller down a little bit I think it'll be all right and that should put my roller about this far back which should be plenty just to guide the boat up on I think it'll help out a lot so let me get some tools and let's get started on this thing all boats moving get this thing on a jack okay now this is one case where I don't care if this boat breaks off if nothing's going back in there anyway so this is what I did stuck it something like that that didn't work oh it just got the impact out this will be clamped with these these are there are two different ways you can put them this will go on like that needs to be now you can either clamp these on at a first cross this one would go let's say let's say you've got a cross member that comes up down you can you know go like that one on each side so what I'm going to do is I'm going to get these put on here loosely and then we're going to go from there so let me get you set up at a different angle there's no lock washers on these things they've got these nilocks a little bit of nylon around there and once you screw that screw that up on there it makes the nut really tight it won't back out on you I'm not sure what the what size they are let's see to the base well I'll be darn cool see there's I could have just showed you this picture two different ways I'll show you again here in a second these are the caps for the top that's not going to go like this of course I'm just setting it there until we get these starting on let's stick it here what I want to go okay just like that now something like that now we get these screwed in here some and then I'll bring you back when we're putting the roller on okay now we're going to put the the roller in if you want if you want to use a socket or whatever you can cut these off so you use a socket on it I try to refrain from doing that Jesus especially on my stuff because if I find a better trailer I happen to pick up a better trailer I want to put these rollers off here on to the other trailer you know I might have a different setup and then these might be too short then but let's go ahead and get these on here or this one a little bit too much just a smidgen too much so let's loosen one of these up since I've got them crossed this side actually made for that and that so it's kind of like an x pattern so it shouldn't take much just you know trial and error on something like this because remember you're kind of fabricating this to fit your trailer because all trailers are different you know you can have two identical trailers but there could be something different about them yeah I'm definitely going to have to lower that roller down it's not going to be that big of a deal so I'm just gonna snug this up here just so I don't move and I'll show you what I mean about this roller that I need to I need to bring it down okay so this is what I'm talking about the roller needs to come down see it's barely touching it this is what you want to be here so I'm gonna have to lower this down here some excuse me which I'm surprised they didn't make this more you know adjustable for different boots but anyway so let me go ahead and get these snugged up because they're about where I want them let me get them snugged up and then we'll move on to this okay I got this tightened about where I want it okay I still got plenty of threads down there so what I got to do what I was telling you this needs to be I want this part to be about right here so I'm going to lower this down as far as I can go with it and drill a couple new holes so yeah I'm surprised they didn't make this more adjustable with more holes either in here or in this thing so I don't know I'm definitely going to have to make the holes in here but that's okay no biggie I'm gonna go ahead and take this off as you can see it's fairly straightforward I wish the rest of it I could tell you it was straightforward but it's not because your trailer may different be a lot different from mine and like I said every trailer is different you might have two identical trailers but you put two different boats on it you may have to adjust these and put these different places so like I said you got to use your head but so anyway I'm going to go ahead and take these out we'll get these holes marked where they need to be and we'll drill them out okay guys so I loosen this up so I can adjust to where I need to be for my rollers so now remember if you guys go well I want plenty of room here that's understandable you're going to want some room you don't want it right up against it but if you're out two inches on this side you put the other one out two inches that's four inches of play so if you're if you load your trailer you're clear up against this one that means your trailer is going to be all four inches on the other side that's too much for this boat I'm going to go about a half an inch on each side that'll give me an inch if I'm over too far one way or the other because sometimes if you get uh there's a there's a boat ramp right down the road here and that lake is hard people have trouble all the time getting in and out of there and it's just it's kind of a pain for that reason so it's hard to get your boat on straight all that jazz you know so I'm going to get these tightened up I had to make ground holes because I couldn't make square holes so I'm going to have to get vice grips or something on here to hold this because these are locking nuts I may just find me a couple nuts I'll need four of them that'll go on there and put a lock washer on so let me go see what I got okay so now are you in frame now I'm going to straighten this up I'm going to go one pinky my right pinky uh that's about where I'm going to go there now I'm going to tighten these boats back up down here and this side will be all done uh let's stay sure right now okay so that's what I'm going to do I'm going to jump to the other side I'm not going to bore you with it because the other side just going to be a mirror image of this about one pinky uh we'll see how it loads and unloads I'll carry a wrench with me and I can always adjust it if need be right there at the ramp so it's no big deal okay so there's what they look like tightened up like I said you can cut them off if you want I just like to have the versatility of getting them you know in case I want to switch these to another trailer so yeah uh I would have had this done the other day but we had like three days of rain and the other day it got really bad well I was going to do some more work on the boat but you can see thunder lightning check it out had another little tree come down which I was going to cut down anyway for the neighbors but so yeah all right let's move on okay guys so I've got this side done we got a little caps on there uh those will probably be coming back off because I'm going to extend these up a little bit higher maybe another 18 inches 20 inches and I'm going to put I'm going to get rid of them lights I'm going to get the smaller ones and put on top those are just too long to be sticking out and uh same way with on this side now that should be about right so yeah if it if it's one way or the other it's not going to be enough to where the trailer is sitting real super crooked and these according to my measurements are out wider than this so it should come off okay and go on okay if I gotta do some adjustment down at the ramp you know I'll just take a wrench with me and I'll do the adjustment down there sometimes you gotta do that but this should be pretty close I think so so there you go that's how you put them on okay guys so I'm going to go in get warm or yeah warmed up really want to go in and get cooled down this is what I was telling you about there they can either crisscross or be side by side depends on your thing but you can't be real specific on how to do this because like I said you might have two identical trailers with two different boats on them so you're gonna put them on different they're gonna adjust to the boat they don't adjust to the trailer but that's you know enough to get you started now you kind of know you got an idea of how to put them things on they're real simple when I extend these up and move the lights up oh bring it along with me for that uh you can also get those big tall ones that um they're PVC but man I why does it work that's what I did you know trailers just probably two or three a week come in needing new ones they'd break them off because they're galvanized so far up and then the rest is and and they get beat up I mean you're going to beat these things up so make sure they're tight but uh you know they'd be breaking them off and stuff and so mostly what a lot of guys would do they'd be can you extend that up so it's metal a little higher and a couple times you can buy just the rollers a couple times on the bigger boats they had me put the rollers up here because you know like the side of their boat would be this high so they'd have me put the rollers up here so anyway guys there's just so many different ways you can do that it's real easy like I said this is your main tool up here um so I'll bring you along with me when we get it out on the water I don't know if we're going to go to day or not hell it's 92 degrees out so 91 92 ish so I'm going to cool down and I want to say thanks for coming along with me guys I appreciate it and stay tuned for when we get the boat out and check and make sure there's no water coming in so we're getting there thanks for coming along with for the ride with us man appreciate it shea berry met the man legend gone for now don't forget to check out monkey 1000 channel appreciate it thanks monkey and thank you guys I appreciate it we'll see you guys soon bye bye and take care