 this is today's project get this sorted first swap over and get that one done they were all set up all ready to go if you look at the camera now with your embarrassed face i can zoom in when i go and edit well you're a digger there it's a bellware state back there anyway enough of that go under the pack of block orders for today coming today this is today's project get this sorted first swap over get that one done we've got left on here is a full block and then a 150 cut which works perfect with our padstones which is going to be a 150 lintel so what i'm doing at the moment is getting the boards down to protect the slab because it's only this was obviously only done yesterday a couple of boards down start to pack up get them up ready to go get it loaded out mixers on Danny's done the mix he's gone off to do the screw run and then once that starts opening the board down get it all loaded out with all those the handy block grubs so that's today's job whack this one up as high as we can drop onto this side get that up as high as you can and then hopefully if we've got time is get the trestles up get set up for finishing off there's a window in this side a high level window so this height about two and a half courses high and it's about 11 40 wide just for ventilation it's going to be a flat roof for the lantern so yeah the slab's gone off nice always always nice to get the slab in so it's solid to work off so i'm going to stick it back on time-lapse get all this sorted out and get loaded out and by that time the mix should be ready so catching a bit that's then chucked up that's as high as i can go with the trestle now yeah it's going to be two course of block and two course of brick well the block cut down ready for setting this out now actually take the damp course down just a quick one whenever i'm setting this wall back here i always just do it by eye and it never works out so what i've just done now is square use the proper job so here there's that smart getting out i just need to make sure it works that line now so i'm going to get me damp course down get set up insulation's ready to go and then have a quick break and then crack on so we'll see you well put in time-lapse first then the safety 10 plus 12 that's the first mix you've done need to go with dining to come look a little job i'm going to try to throw me in the dowel first three years i've got a two three four five six seven eight nine ten eleven twelve about another nine blocks no eleven blocks loading there a couple more cuts to do but we're getting there coming on nice just get a level up with that and then swap over to there this afternoon loads of cuts but it's always the same on the internal you've got to cut there cut in that corner cut there and then a cut there and then the opposite course cut there and cut there then because it's you don't really want to use the cutter not just because i'm messing the garden up but i'm covering the sun cream so i'll end up gray so i'll just do it with the ball stuffer now just carry on join that up after dinner going over for this job so catching a bit there we go 20 plus four yeah 20 plus four it's thursday the 23rd of may sorry tuesday yeah we're away tomorrow and thursday and friday so me and alts be back saturday because alts come back thursday so we've got obviously we've got this to finish there's our window and then dany's in the next two days he's going to give us all out all of us to work to at the top there's our padstone there but that's going across that way for the steel which is a 152 by 89 so should be handable for me and alts on our own so yeah um this is the side all done that was um yeah that was done flat was that was done from scratch we had to board it out do all the cuts load it out build it and then swap over same again board it out do all the cuts and get it built so i've not done too bad not bad for now for the gammy leg so yeah there's not much to do you can see the top there across there i think it's another two two and two three two and two thirds courses so two full courses and then one fifty course but i'll know better when we come back and saturday good saturday morning on this glorious saturday the 27th of may we're back the band's back together alts back from sweden we've got back from drakeman drakeman and lemington yesterday so i haven't had the last three days after working the weekend bank all the weekends so i don't think we're working monday and then we've got a new project to start tuesday new extension so here we go so we're up to so danny's been in and it's done a little bit of block work for us and he's given us our he's put us a piece of timber up each side with all our measurements to work to there's our steel ready to go in which is going to go in tomorrow morning we're going to get everything set up ready for it so it's gone off for the morning i'm just going to get the profiles back on the corners i know it's only two courses of block but the reason i'm putting the profiles back up is so we can get a laser level up and get the marks put on to the onto the profiles with the laser get everything nice and level um i'll actually just get in the mix set up at the front down there somewhere hello i'm back and uh so is dad from his little lay trip we've both had a nice little holidays i went to sweden as mentioned and dad went to drayton manner with the rest of the family daisy's first time at thomas land so but we're back in work mode now so we are back on the extension and obviously dad and dan have been busy since i've been a since i've been gone uh i think all that's left now is a from the from the top course a block and a 150 cut i think all right no it's not because the outside comes up the wall plate goes on the inside so this block we've got to come up yet to think to the top of steel i see yeah it's got a laser for our marks and um this is our every wasting everything off of these all the measurements and the placement to there so we've got all that um yeah so that's the job get get this finished i think the steel is going in tomorrow with dan's help so no stress with that today we'll get that sorted tomorrow it's just get everything set up so we can finish tomorrow so yeah i will set you up when when something exciting's happening see you then glamorous assistant hello yeah we've set the laser up to the bottom of steel you can't see that in the sunshine but it's there on the line you can see it on the back wall like it's gone past yeah so you should see it on that wall that camera should pick that up so i just took a pencil mark on there in case we do lose the laser and i've marked it on the profile it's like i say we don't really need the profiles up but the profiles we can put the laser lines on the profiles so we've got our marks and we've got our profiles to work off oh yeah show me a quick view of what's behind there you go got a bell way of state just kicking off got a couple of houses done down that end and then you can see they're doing the all the groundworks roads and sewers so should be nice got a nice long garden so they're not overlooked too much so yeah there's a good review from up top so we're going to try and get this across to there see if we can see if it'll pick up over there we do have a target got the target to help us pick the line up we're still working out to use this thing but yeah so yeah this side this side sets up so there's the lines there's the lines so that's our bottom of steel height so yeah i'm going to hop across the other side get that side done and then we can work the cuts out then then we've got a 150 cut underneath the padstone and there's a 150 padstone and Danny wants us to put the padstone from front to back so we'll sort that those cuts out and then that'll be going off overnight ready for that to cut tomorrow and we'll get the trestle set up for us all to throw that up tomorrow it's not a large steel that so it shouldn't be too bad and window in there just two course of block deep i've got the lintel for that too so yeah it's just a matter of just getting our head round it getting ourselves organised and then we're away then so that's it i'm going to get back on this and get those marks put over there so catching a bit wow look at that anyone who likes planes look at that today we had the the blue come over the other day the airbus that brings all the bits into i don't know it's called the air base down at the chester that makes the airbus wings for you get all the um Liverpool planes coming over and Manchester planes and for some reason they come up there in turn and head that way anyway that's enough about the planes yeah we're all sorted we can actually take the laser down now because i've put all my marks on i've put all extra marks on the the the written on bottom of steel so that's that's the bottom of steel and then there'll be another course of block above that same over there put all the marks on the walls and if you look so i'll show you this one on the profile at that end it's your piece of white mass masking tape same here bottom of the tape is our level i'll just show you with the other one just push that round there you go just see the green line everything's set we don't have to check anything back now we worked we work off what we've got thanks to this thing yeah get me around the cuts now get all the cuts done before i put me some cream on and Alex is going to get a half a mix around the front because there's not a lot to do and then we're going to get cracking get everything up so Alex is back Sarah and Stuart are off to Ireland to a wedding so we have Daisy for three days so we should look shouldn't say that she's good as gold but she might decide to have her knock down my mummy and daddy out there maybe anyway yeah um there's not enough to film for a bit now so once we've got a mix on and that and a few cuts done we'll get back to you there we go this is the equivalent to the murder lift on site when you're at that height where you there's a lot of faffing about when you knock don't get much done so um it's way after break now all the cuts are done i've done 27 of them don't think any 27 because i've got the window in it yeah they're all done i'll set up the trestle i've slowed it out i've got the mix in he's currently bringing some water around and we're going to get this side up first then we'll see how we go on from there have to carefully put the camera now with the sun so yeah like i say we're all set up all ready to go i'm going to stream the line up put a spot board up and then get cracking Alex and John but we want once we're all loaded up so um yeah let's get set up and get cracking so happy days we got one lintel in that says more or less done but we've run out of water and uh drinks are coming so we'll be going for lunch but after then we're on there and that'll go a bit better because one there's already 99 percent of the course up and all the cuts are ready so we can get started on that immediately so but progress thank you Richard figure the Fitzbrick has many uses beyond the that of bricklaying so uh yeah we'll catch you after lunch should hold on what we're holding on for sorry Tom so that's what's going on with the padstones bridging the cavity but because we've only got one we've decided to put the off cut in there so it's all padstone now that's full 200 and it's bonding the walls as well ready for that so on top same over there we've got a couple in the garage haven't we can bring tomorrow yeah get that one on we'll slot the bits in the back tomorrow morning before the steel goes on top very bizarre but hmm so i'm done here now a lot a lot later than i thought it'd be after is it probably yeah yeah it is pretty scorcho today i'll just point you straight at the sun oh yeah yeah so anyway that's up i'm pretty sure that's stealing right now any different we'll find out tomorrow and we'll add to it or whatever obviously there's your steel height steel to go on and then block to go over the top well more cuts to go over the top of the steel because the steel is only 160 so we'll go end up with a another few of these thing cuts across the top and then the wall plate is just across the front of yeah because the spars run through the back so we only need a wall plate front to back there along the front over the steel not sure oh yeah block work same height again all the way around basically live around at that height we'll leave the profiles up tonight they're just handy and we're going to drop this move it over there and get as much as that done we can today and then crack it off tomorrow love it we'll have to test that if we can have that piece of wood the A&E method yeah Robbie and Robbie as well yeah so yeah we're going to move that back this way a bit move this all around over there and carry on like i say we spent an hour working out getting our head around it and getting all the cuts done so this is why you don't do extensions on a price it's all right you're throwing all that up and that up in two days and just while opening it up that's great and then you get to this murder lift with all your cuts and you're setting out your doors and lentils and sometimes cavity trays but on this one we don't need cavity trays because it's a flat roof on top high above the window so there's no and it's and it's rendered so that's what the cavity trays in so that's enough waffle i don't want to look at the time because i'll only make myself nervous well what we've got for us this time is one cuts are done and we've got an extra course already done well almost plus we know what we're doing we've done this side now we just copy that apart from the window yeah so that's it it's funny enough because there's a window in it you think it to be quicker but it's quicker when there's no window in it you're just running backwards and forwards windows slowly down obviously we've got no lintel to be messing about with and no plumbing up around the windows and stuff so thank god they got that old camera if you look at the camera now with your embarrassed face i can zoom in when i get on the edit right let's shut up and get down and get packed up packed not packed up moved packed up let's shut up and let's get down there and get it moved unfortunately we just we just ran short and water we were like a bucket full short but it's about quarter past four now so on a saturday yeah so we're just gonna get we're gonna get finished up with the jointing and just finish this off tomorrow we've got the we've got the padstone on we've got that part on which is the main thing obviously like we said before tomorrow we're gonna get the ones from home and put them in that gap but that's set up for the steel at least so we can continue with that tomorrow and then once once we've got a mix ready for the steel and whatever you we'll just get all that done at the same time so yeah so all that's left to do is joint up and tidy up and i'm trying to tidy up and that so yeah we'll catch you tomorrow for the steel just turn the prodigy down so what i know turn the prodigy down right so they both in yeah i've just popped the two pastures from home in so they're going off now solid um just thinking about this on the way here i'm i'm thinking that's like a cold bridge on here and it's bridging the cavity but we're working this is not our job we've been asked to put them on like that so we'll do as i told but it's rendered so it's there's not going to be any water penetrating through the plus their dense concrete so that's not going to happen um yeah so ready to get that up to the and then up to the just me and the just the two of us today so so we're going to get that up get the cut set out alex we're going to mix in i'm going to finish tidying up here we're nearly done now well that's going to finish tidying up while i get this built in a bit of pointing to go over that we didn't finish yesterday need to get that dance sorted towards a bomb site yeah right i'll hand the camera to alex and he'll put it on the steel and i'll go and get the gopro to time lapse it from here there we go you did it just the two of us it's all about taking your time getting up bit by bit so yeah that's ready to go now course the block straight across the front course is split across the top wall place on top of that and the bit of block which is doing that corner just to finish that side off just spot blooming level is there for you have a quick break now and then get stuck into after break and then i can pretty much 99% say barely finished today and then bank holiday off tomorrow bank holiday Monday so catch it before i get me some cream on stales on i need to get a line on here now string it across get our cuts so i've got a cut there which is a 360 obviously these cuts let's get a nice room across for that and then we'll find out what this is that's going to be trimming back when it's all gone off yeah all set to come across here with our block work and then a split and then wall plate top of steel six by three so that's wall plate height actually there is no cuts over there so we're going to knock that off is the top of the wall plate but that is top of wall plate if you just follow it around like that so that needs cutting off chopping down level with that so i'll level across through the pencil and mark that up could you have spotted that and then this is going to be the same that's going to be cut down so there's no splits to go over the top just the block way to go on the outside so that's a lot less cutting to do so forget about stringing that line across we're just ready for running this in yeah Alex is currently getting the mix on i'll get these cuts done before i put me some cream on and then get cooking that's a little bit in that corner i'm guessing the tellage go in there ready for wall plate which runs through to here steel on double insulated and block work which is just nice to maintain and take a feel of the wind so you'll be able to hear it and yeah we're done just going to stay enough because this is this is danis which i'm going to take our plank back which is that one i think long one at the end and give it a brush out and then we're done we're gonna have a quick dinner now and get the last bit of tiling up to dinner just stop pointing this out to you look at that it's a strange one isn't it the tiles just bedded on top of them tiles see if i can zoom in there you go look at that doesn't leak as far as i know but not good is it gobbled on and then the lead curled up at the end to direct the wash into the gutter not good but anyway it's not leaking so it's not leaking there's the skylight in that roof and obviously this is going to level across into this one now give me a nice big room this i'm just getting our profiles down and i'll point the holes up in here so we'll catch you after dinner then we have a quick time lapse tidy and then an outro for Alex well there you have it i was here for three days of this so all credit to dad and Danny for his help so i'll just do my job at the outro so thank you all very much for watching if you enjoyed be sure to give a thumbs up and if you're new to the channel you want to see more of this and everything else we do be sure to hit subscribe and tap on the bell so you're always notified when we upload there's always a massive help and we greatly appreciate the support this has been Brick Lane with Steve and Alex with a pretty nice extension we'll see you in the next video