 Hey everyone shaker 1,000 here today I got this old BB gun it belonged to monkey's father and Doesn't want to build up pressure This is a daisy 880 177 so I Don't know much about these These 880s I've had several of them, but I never had one apart never had to take one apart but I Done some reading online. We're gonna we're gonna check the seals out and see if that might be it And I'll explain to you what else it's doing. So stick around another late-night video It's 1145 right now. So let's see if we can figure this out and I'll get you a different camera angle here Okay, guys. So like I said, I don't I don't know much about these daisy 880s. It's just This one was made in Rogers, Arkansas, USA And it's a 177 cowl 880 BB or 177 cowl pellet It will pump once and it'll shoot it'll fire but But um, it doesn't even have the power to I mean it would stain you if if you got shot with it But it doesn't have the power to even go through Aluminum can a pop can so there is a There's a lot number on here and a pack number. I might try to look them up But what I've seen online is is that these seals inside here go bad Like I said, I've never had one of these part. Not sure how to do it. It is unloaded. I Don't know if that's an oil hole or screw hole. So this thing may have been been a part before I'm not sure but I do remember I have shot this gun a few times and you could pump it up And it would pump up pressure. But right now, you know, just one time. I mean Is all you get with it? well chamber this thing make sure there's no BB in it, but Yeah, so it's not even it's not even doing anything right now. So Let me release this pressure On this thing. I'm gonna go to the door just in case hang on. Okay, so I was just pumping it up and you I can hear it Losing some air pressure there. So let's go ahead the seal kit for this thing a rebuild kits like 30 bucks I mean, it's an old BB gun. Come on, but I would like to get it work We have some very troublesome squirrels out here And that's why we haven't even had to we haven't got to put a garden in we didn't get to put one in last year The year before last, you know, I was growing them onions. They were doing good and the squirrels just ate them on and now they're Getting in monkeys bird feeders eating all the bird feed so the birds don't have anything they're knocking over the bird the bird baths They're just nuisance So that's one reason why I want to get it working, but also it was her dad's so But I don't know how to take one of these part because I've never had one of these part before so push that pin out seeing this Okay, this is awkward a little pin right here right there that pin Pull that out You know what hang on I'm gonna grab a paper towel so I can put these things on here and try not to lose them That's better Now let's just slides Slides right out. There we go. I got some seals falling out here. I feel like plastic I don't know if it's supposed to be plastic or rubber, but it's plastic Maybe they're extra seals because out here it wouldn't do anything Okay, there's a chip out of this thing Okay, now Yeah, this this seal right here. It's like a felt seal and those two o-rings. They're like 30 bucks As you can see it's well oiled up. I've got a nap mess with me. So I'm guessing Yeah, that's kind of buggered up there, too There's a pin right here that is really buggered up there. I'm not sure Let's just take this out of here. I don't know what all these up this other stuff It's from it's got a little hole in it. That's supposed to be there. This is all cracked up Identical to that Yeah, that looks I think that's just a roll pin that gets pushed out and this whole piece will come off But I don't know if you can see that that right there These other two things then these might be spaces for here Down here I'm not sure what these are for because one's okay This one has a hole in it. Okay. They both have a hole in it But my understanding is what I seen online. I did research it a little bit Is that this one here is usually the one that holds the pressure well not usually it is one holds the pressure and they say soak it in Break fluid I've done that on more than one occasion on different stuff and What it does is swell the seals up and makes it tighter a tighter fit But I'm not sure where these came from so I'm gonna have to Google this and find out and find out Where these go because I don't know All right, let me do some research. Let me clean my hands up Let me do some research on this and I'll get back with it Okay, so What I found out is This is a 1977 They started out 1972 and ran to These white spacers here 72 hang on a second. Let me check this. Okay, so 1973 To 1977 They had the blue metallic. This is the blue metallic Okay, mid to late 70s had gunmetal finish and April 1979 is When they went to satin black so This is this is the blue metallic. So this I think this is a 77 because 1972 until 1974 they had these white spacers From 19 from April 1974 until October of 1976 they didn't have this white spacer Okay, 19th November 1976 has white spacers continued until the present day So this being the the blue metallic With the lot number That's why I'm thinking this is a 77 because That's the last year and it had a lot number instead of a registration number and And it was the last year That the that they had the blue metallic The last year blue metallic is seen so I know it's it's not and I know because of the lot number of The in the 70s of when this had begun so Patent pending ended and patent numbers began. Okay, so 70 1975 October of 1975 is the first year seeing what they stamp stamped Patent number and this has a patent number doesn't say patent pending Okay, so I Know it can't be a 78 Because of the color of it. They went to and then you know 79 is satin black It's not a gun metal finish It is a blue blue metallic and that ended in October of 1977 is when the blue metallic ended so From what I'm coming up with this lot number is is this is a 1977 So yeah, all the parts are pretty much the same it being at all and now I don't know where he got it Monkey doesn't know where he got it and her mom's asleep so we can't ask her so This being the year that it is and that it belonged her dad I might consider putting some new parts in this thing after all. I'm up muck's going to the bathroom So yeah, I think I Think that's what I'm gonna do, but I'm gonna clean this up. See there's still a lot of oil in this thing And I think I am gonna try to soak this And some brake fluid Just for Nostalgia reasons and that it was her dad's I mean who knows maybe you bought the damn thing new We don't know Her mom might know but like I said, she's asleep. So I'm gonna get this cleaned up and I think I'm gonna try to soak this into some brake fluid in fact, I might go ahead and turn the rest of that now and Yeah, it's gonna be a late night, but I'm gonna go ahead and put the rest of this down and And Get into here and I'll film that for you, but I'll speed it up Now they really know just what you want With you, I don't ever feel calm I could feel the sweat inside my palm Play with me like cats and a string You don't understand the pain it brings You don't ever want to get me You know, I'm addicted to you and it's twisted you can give you with the evil Got me coming back for more even when I've been screwed. That's full of pins. Here's my heart straight through I don't know how well you guys can see that right there 77 just trying right now. I'm trying to see if it has a smooth bore Or a rifle bore. It's a smooth bore So that's putting me about in the right Range of a 77 There's some stuff in here So I think I'll probably end up have only to buy a rebuild kit for this eventually I just use it for small game and You know just playing around with it, but okay, this is nasty looking in here Let me get this out here for you over right out here Now where you want to be able to see inside that So that stuff inside there Is missing a screw and one was loose I'm just wondering if someone didn't have this part before and replace something But didn't clean it. See all that stuff there all that black stuff Shouldn't be in there It's real hard and down inside Look at that over on this end here. Oh, yeah, it's real. Let's show this through here. Oh, yeah It's got all kinds of black gunk in there. That may have something to do with why I wasn't sealing But I know it worked because I pumped it up a few times and Shot it out back and it seemed to be, you know, fair fairly Powerful. Yeah, look at that. Okay. I'm gonna get this all cleaned up That may be the issue right there because I could hear air leaking out of it, but I couldn't tell where from Let me get this cleaned up And I'm gonna clean this up real good. I'm gonna suck that in some brake cleaner just for a little bit and Until I get this cleaned up and we'll see if that helped any disease That that is definitely feels like rubber But this feels like plastic That's plastic. That's rubber. The rubber feels pliable. I'm not gonna mess with this with this one This is rubber pretty pliable that spring goes in here So I may soak that for a few minutes All right, let me get cleaned up and I'll be back with you guys in a minute hang tight But I'm thinking all that black gunk up in there. I Thinks coming from this piece right here Because it looks looks pretty ragged Well, that's not gonna seal, you know, but here's the seal here So I don't know how this would get past this seal to get up in where it was again Let's get it cleaned up get some of these parts so can You know, I could hold monkey and she agreed. I mean, it's not working now It's worth the shot to try to get it to work And if it don't then I'll I'll go ahead and rebuild it if it was something from the 80s. I wouldn't care I mean if I bought this at a Yard sale or something I wouldn't really care about it too much. You know what I mean But it was her dad so I'm gonna See what I can do to save it You guys know I'm into vintage and nostalgic stuff. So So I think this is called a wiper here But that see that looks pretty good But see so this would go in here like this So how this black stuff Got up in here. I don't know Yeah, I think it's just kind of like an oiler But I'm gonna soak that I Am gonna soak this one. The tube looks great inside there. So this whole can't Can't get my thumb in there to block that hole but All right, let's continue. Okay, so I think That other piece with all that black stuff that's coming out of it. I think that Is the problem So let's go ahead and put this back together. I'll speed you up for this Missing there so pretty sure I don't have any screws this size. I Mean I might have in there somewhere, but I'm gonna look right now Because I think I'm gonna have to tear it apart again To rebuild it. I soaked a couple of these seals and brake fluid I can still hear and this is coming clear out though new seals put new seals in it, but that's alright That's like coming clear out of there. I don't think it's gonna come out for a while Let me study this make sure I got that in there, right, but yeah, I think that's I Remember it coming out too far before Okay, let me check up on this. I think it's right, but We just have to give new seals and put in it. Okay, everything seems right. It's just not Just the seals are bad. So Let's go ahead These back in here brake fluid will work in every night, but I think I'm gonna go ahead and yeah I think it just needs rebuilt whatever that is down in there that black stuff there What was getting up inside? Okay? Let me hold up get my mess cleaned up I'll be back with you guys in the second. Okay guys, so I can hear it Leaking I don't know if you guys could hear that or not. Yeah, so it's definitely leaking So that's what it does. It just needs new seals. So All right guys, so there you go just uh Just messing around on a Thursday night late at night Man, it's like two o'clock now. I've been messing with this thing. Well, I took a couple breaks, but anyway, so there it is 1977 daisy 880 so yeah As soon as I get some extra cash, we'll get some parts first thing we'll rebuild it and we'll go shoot it some cans or something Thanks for watching guys. Appreciate it. She barely met the man legend gone for now You'll have a great weekend tomorrow's the start of the weekend. So y'all be safe. Take care. We'll see you next one. Bye. Bye I think I fixed it That's the entrance hole That's the exit we'll go outside And I'll show you Okay guys, I don't know how this shoots but I'm gonna go For somewhere right between These letters and these letters Or anywhere on that side Let me zoom me in. I'm gonna be I'll show you. All right. I gotta bring it clear around. Hang on All right, I'm gonna be just to the right of that tree and I'm gonna go Try to go right between them two letters there So I got to get this thing loaded and pumped up. Okay guys So I'm going back over by that tree So give me a second I'm gonna bear down on it And we'll see We'll see if I can hit it from back there I should be able to All right fire shooting a little low So Let me get loaded up. We'll do it one more time I'm gonna go about right there We'll see what happens. Okay guys I'm gonna be going for about right here anywhere right in here I'm ready to go. All I gotta do is take it off safety We'll be ready to go. So give me a second to get back here and get buried down on it and I'll tell you you're ready You watch for it. Oh nice Went in there Came out there awesome Okay guys, whoops, hang on a second. I'll tell you what I did to fix it Now I don't know how long my lens was messed up But it was like I don't know if I put finger prints on it or what but It was nasty. So If it was bad, I'm sorry But what I did was that spring I don't know if you guys saw it But there was that little spring in there about this long About a big round is my pinky It held that one Piston with with a with a seal on it It works kind of on the same basis as as a master cylinder and car But it held that one and the one you pump with that goes up in there holds them two together I just stretched it out And I pumped it up about 10 or 12 times and went out front and it made a good good loud pop And I was like, oh, we got to go back and try this and I tried it And I was like, okay now. I got to show you guys So if you have one of these and your seals look okay, but it's acting up Take the part try to stretch that spring Also, there was something about these These rear sights too I think it was 1978 or 79 Might have been 78 was the last year they had to screw on Sights on the rear They were welded on after that. I'll put it in the description, but I think it was uh 79 when they started welding these sights on some I'm I'm about 99 98.5 percent sure It's a 77 so And it's still working All right guys for real this time. I'll see you guys in the next one. Thanks for watching We'll see you soon. Bye. Bye guys