Bumper Installation, Shocker Bolt
Loading...
Loading...
1,602
Loading...
Uploader Comments (balfanater)
see all
All Comments (5)
-
thanks a lot bro.. i'll set the dwell to default and set it all over again.. you helped me a lot
-
ok thanks i didnt know wtf they were. my shocker uses 1000psi for 1 pod and i have H.E. bolt nothing is stock besides the body and i have a cp reg all the setting on my virtue are set to default.. have any ideas? i need you to tech my gun
-
whats the two little screws in the back under the bolt on sft shockers
Loading...
9:02
Front Bumper Removalby richpin06a37,892 views- 9:13
Shocker HE Bolt Maintainanceby sft33032,728 views
- 1:29
Clear Bumper Installation Videoby mbagz4201,751 views
- 6:12
Shocker/Nerve Disassembly/Board Removalby sft33031,228 views
- 4:38
shocker stock board adjustmentby balfanater7,882 views
- 0:28
shocker board removalby balfanater578 views
- 2:17
ClearBumper Intallationby ClearBumper821 views
- 2:44
Trailer - Shocker NXT Tech Tourby PigTVProducer23,549 views
- 1:20
"Bolt on" Bumperby dieseltoyz312 views
- 2:02
Lexus IS250/350 Rear Bumper Applique (Protection Film) installation DIY - Part 1 of 4by TheLexusNet2,117 views
- 0:49
Tech T Enertia bolt in SFT shockerby MrBlackMamba10001,097 views
- 3:32
Installation Video - Automotive Bumper and Trim Restorationby AutoTrimDESIGN4,518 views
- 4:43
Rear Bumper Fascia Removalby richpin06a8,023 views
- 0:45
shocktech sft shocker HE bolt nerve frame tadao dynasty board hybrid bolt guide gun on semiby 98saturnwag1,603 views
- 2:36
mammal the majority www.0daymusic.orgby MrNuttyT768 views
- 0:23
SFT Shockerby shiznit9091,597 views
- 4:30
shocker upper board powerswitch repairby balfanater1,896 views
- 8:14
NFS Carbon How To Make Dom's RX-7by LeeH1989211,678 views
- 8:50
Shocker SFT/NXT eye ribbon installationby ydna2674 views
- 7:48
How to remove the bumper from a Lexus IS250 / IS350 to install Lite-Eyes CCFL Halos / Angel Eyesby LiteEyesInc21,914 views
any idea of how to make the shocker use lesser air... it really uses a lot of air
burnout2020 3 years ago
Optimise dwell and HPR settings also the HE kit with a NOX Kilo (or whatever the new version is, stopping power I think). That's pretty much the ultimate off the shelf. A guy on PBN has a spring mod which I started a while ago and he beat me to perfecting so I stopped, give's excellent efficiency (around 1600-1800 per 68/45)
balfanater 3 years ago
thx bro... i'll try it.. oh yeah... another question.. if is change my board... will it make any difference?? as in the air and not the mode
burnout2020 3 years ago
not really, you just have to set the dwell and HPR again
balfanater 3 years ago
solenoid inserts, they seal up the air paths making sure the air gets to where it needs to go, leave them and you'll be fine. It's rare they are a problem.
balfanater 3 years ago