Hydrogen Tap (16 plate Car Config) 113
Loading...
Uploader Comments (johnaarons)
All Comments (7)
-
steel wool rusts big time, so do the "copper" scrub pads...
-
John, By glueing our cork seals only to the clear cylinder's top and bottom (not the lid or bottom plates) and adding springs under the wingnuts/lugs: the 3LR1000T becomes ventable under cell flash while retaining a sealed ability. Cheers, Russell
-
send me an email at "johnaarons at hydrogen tap dot com". John AArons
-
Concerning NTE's Pulse Width Modulator (PWM) chip: ECG1721 (16-pin DIP). NTE's ECG1721 is match to ST's SG3525A (both are NOR logic). It looks like + 12 volts is [pin 15], -12 volts (ground) [pin12], output towards power transistor [pin 11], Variable resistor across [pin5] & [pin7] (controls delay), This is as far as I reached. Help?-What type of component to control pulse and across what pins? I guess the worst is to miswire and destroy my $6.25 chip. lol
7:54
Hydrogen Tap (3LR1000) Upgraded Cell #56by johnaarons3,813 views- 6:23
Hydrogen Tap (Honda Installation Begins) 114by johnaarons5,933 views
- 1:15
Hydrogen 2 cell running carby nanorocks200856,052 views
- 4:52
Hydrogen Tap (AAron's 4 Plate Test )#79by johnaarons4,481 views
- 7:18
Hydrogen Tap ( 3" by 8" runns and more) 112by johnaarons5,338 views
- 1:03
Hydrogen Booster govsecretsby govsercrets979 views
- 5:34
Water4Gas Hydrogen Hybrid Conversion - How To Convert Car Burn from Water As Fuel Sourceby WaterPoweredCarKits3,837 views
- 4:56
Hydrogen Tap (Installation Strapping to Honda) 115by johnaarons11,066 views
- 1:23
run your car on water wes hydrogen, hydrogen fuel cell, gasby bettybeem2,289 views
- 5:49
hydrogen Tap (Great New Information) 109by johnaarons7,220 views
- 1:14
Hydrogen Generator HHO Fuel Cell Car Conversion Kits - Get Best HHO Plansby WaterHybridCarKits9,966 views
- 10:03
Hydrogen Tap (WidowMaker Tests) 130by johnaarons3,805 views
- 8:13
Hydrogen Tap (New Cell for Honda 3x8) 107by johnaarons3,892 views
- 7:31
Hydrogen Tap ( More installation to Honda ) 116by johnaarons10,716 views
- 5:57
Hydrogen Tap (Clear View Tube-PWM chip)#98by johnaarons9,696 views
- 4:13
Hydrogen Tap (AAron's Cell Close Up) #58by johnaarons6,163 views
- 1:20
Hydrogen Fuel Cell with 5 plates. Completed Unit! mixcatcom HHOby mixcatcom663,347 views
- 7:31
Hydrogen Tap 1 (Testing 110 Volt System) #28by johnaarons6,002 views
- 7:02
Hydrogen Tap 1 Series 3 (Hydrogen Separation Tower) #33by johnaarons17,311 views
- 6:25
Hydrogen Tap (How to make AAron's Cell)#78by johnaarons136,784 views
Make a box from metal. Hydrogen in on one side, out on the other. Fill box (realy stuff it) with "steel wool". Not the fine tread, but the one to clean cooking pan's. This will absorb the heat of the flame and prevent it fom goiing into the hydrogen generator. The fine steel wool will burn, so don't use that. For safety, don't scip the cork
imnama 4 years ago
sounds interesting... John AArons
johnaarons 4 years ago
Why not use a flame arrester as used in gas-welding equipment to be safe? I think the corks may not be enough ...
ReyCad 4 years ago
I am looking at that along with the bubble up system. The problem is that Hydrogen burns much quicker than most gas and the valve may not be quick enough to stop the flash back. Until I know I can't depend on that. John AArons
johnaarons 4 years ago
It works, need to get an ossiacetylene arrestor.
I tried to turn on the gas with this arrestor and the flame goes back to the flame arrestor and stops
francobizz 4 years ago
Thanks I will look into it. John AArons
johnaarons 4 years ago