Furnace not lighting
Loading...
Loading...
43,608
Loading...
0:33
Gas Furnace Symptom of Flame Sensor Failureby jimthepianoman171,589 views- 7:20
FURNACE HOW TO BASIC TUTORIALby AbilityJohn179,029 views
- 0:06
Special Talentby NerdOnTheNet6,995,785 views
- 9:42
Gas Furnace Troubleshooting (Igniter)by manopacs1121,719 views
- 0:56
furnace not lightingby smhiebert47,134 views
- 7:35
Pilot Light Won't Stay Lit - How to Replace a Broken Thermo Couple on Furnaceby sketchyvan86,719 views
- 1:42
Gas Furnace will not lightby bigp5831,488 views
- 0:56
Limit switch on Carrier furnaceby jakeduke128,623 views
- 0:24
Pressure switch - Manual reset mechanism in actionby bobolufson30,730 views
- 6:45
gas furnace ignitor replacement.wmvby hvacrepairguy10,180 views
- 2:08
How to fix your furnace by Reliance Home Comfortby reliancehomecomfort65,190 views
- 2:48
Thermocouple Testingby ThePlumbersForum19,284 views
- 1:05
Checking the pressure switch on a gas furnaceby kisssfan122,533 views
- 6:15
HVAC - Easiest Service Call Everby PutSome5tankOnIt8,693 views
- 2:41
MILEY CYRUS GOES DOWN!by onlyiknow113,577,507 views
- 2:05
Tips for Gas Fireplace Troubleshooting - Renaissance Rentalsby renaissancerentals40,102 views
- 1:29
Furnace will not stay liteby guitar54816,241 views
- 6:41
Notaspringchick how to change a filter change in 3dby newsvideowebin3d9,473 views
- 1:30
Gas dude relights my pilot light!by MichiganGirl32148,721 views
@grinosmr hahhahahah yeah rrrrrrriiiiiiiiggggggggghhhtttt JIGGAWAT! HAHAHA!!!
AlboTiger7 1 month ago
@ShayneElijah It's not the flame sensor thats the problem (until you get the flame to go over and flame rod). It's the burner spreader thats probably plugged up that needs to be cleaned so that the flame can spread to that last burner. Blow out the burners and spreaders with nitrogen and check to make sure correct gas pressure is coming into the unit (typically 3.5" W.C) This should solve the problem.
AlboTiger7 1 month ago
spider web or bug in orifice.
poopsmashed 2 months ago
After that blower comes on.Is it ok if the flame is turning on and off every 5 min.
zavalza99 2 months ago
To IWILLGIVEYOUCTIME: If your glow coil won't light up your furnace is rather triped the rollout switch or has a bad glow coil more than likely
drmatt12090 2 months ago
You might have to pull the burners to get it out though so check it visualy first.
drmatt12090 2 months ago
Somethin eather stoping up tube 4 or your orifice on burner 4. Problably the orifice. The brass price should unscrew from the header and you can check it for trash.
drmatt12090 2 months ago
@ShayneElijah Flame sensor is doing the job correctly. There is no flame in the #4 tube. It appears debris keeps gas from flowing to that tube. Clean out burners with a bottle brush.
AlchemistLair 3 months ago
That light doesn't even turn on in ours....We have a similar design except 3 not 4 tubes. Ours just you hear the fan pushing air and nothing else....PM me if someone has any ideas. It's a weatherking natural gas heater.
Iwillgiveyouctime 3 months ago
your flame sensor needs cleaning, its not sensing flame and turning the gas off
ShayneElijah 3 months ago