P5142473
Loading...
Link to this comment:
Uploader Comments (oglundasotarn)
All Comments (15)
-
What happens if you add magnets in the biggest gap?
-
Finish the disk. Or should i say Finnish it.
-
Great job, a few more magnets around the circumference should do it. I think also your bearing friction is somewhat on the high side compared to some of the other disks we've seen. Outstanding!
-
It looks like you have very uniform gaps between your magnets---you might want to make that less uniform as Mylow has stated. but your setup looks good and you're almost there. So great work & KEEP AT IT.
2 years ago 2
-
Keep going. Looks good.
-
Do it! You can make it! Do it! Complete third set of magnets!
2 years ago 2
-
Hang in there! It is a different design, but may be thats what is needed. Actually, I think there may be many different ways to do this. Mylows motor was just one of them.
Nice work, but camera stand please for better viewing out here in U tube land. Thanks!
-
Almost there! Looking forward to see you jumping, shouting and screaming!
- 7:59P5292555by oglundasotarn1,059 views
- 3:02Magnet rotorby mikeperendev222,886 views
- 2:48P5122468by oglundasotarn594 views
- 1:16Perpetual motion gravity wheelby arkann1s91,615 views
- 0:34Howard Johnson Magnetic motorby Eltimple366,887 views
- 4:59P5202516by oglundasotarn356 views
- 1:36Mylow Magnet Motor Decelerating (More Evidence ...by PESNetwork8,408 views
- 0:20hj "proof of concept" IIby Mopozco29,541 views
- 9:55Sterling trying to find right magnet combo on M...by PESNetwork5,585 views
- 8:28Video #5, "Rick's Pipe Dream" Magnetic Motor - ...by TheRickoff9,767 views
- 1:14Звук можно увидетьby xAndron4ikkx245,435 views
- 3:35(HOAX) Mylow Bar-Magnet Motor (Doesn't Start Th...by PESNetwork2,963 views
- 0:21more replicatinby rdelos1disequade836 views
- 0:30hj "proof of concept" IVby Mopozco6,468 views
- 0:23gotter goin!!!!by rdelos1disequade8,070 views
- 1:16SJSU Part 1: Raphial Morgado Setting up Mighty ...by PESNetwork28,312 views
- 9:48FREE ENERGY FROM AIR CIRCUIT PART-3by INVENTOR352,307 views
- 4:48Advice to Mylow - maximize flux gradientsby syncopetra8,026 views
- 3:28003 - Single coil & multiple coils pulse genera...by AndreaGanora130,182 views
- 10:01AnandAadhar's Johnson/Mylow replication trial 1by anandaadhar3,800 views
this is mylow brothers (my friend you are very close to full rotation keep up the good work. this looks like the one my brother biuld a few years ago. you are very very close to replication this is better then bedini group that tried.
sparkyrocky12131963 2 years ago
Tony! Hello Thankyou. I´ve already rebuilt it, obviusly it dident work butt i dident filmd that. my new konfiguration however shows much better thrust. I can putt weight on my disk and it still pushes . going yo post this but today my wifes choir has an consert which will take most of the day. This non cymetry seems to be the trick. Pelle. (thats my name)
oglundasotarn 2 years ago
Härligt att se! Har du fått runt den helt?
Öglunda, i Skaraborg? Jag befinner mig i Tidaholm =) Funderar på att beställa magneter från Storbrittanien, det finns flera ställen där (länkar finns på PESWiki). Om du är intresserad kanske vi kunde beställa tillsammans.
Hade också tänkt att använda en fläkt som rotor, men kom på att istället använda mig utav en skateboardtruck istället och fästa plattan i däcket... Det går till att börja med i alla fall.
Lycka till!
Jimmy
aphost 2 years ago
dä ä rätt å recktitt, tänka säj att en skecker fiellmer över hela väla å så hammnar dum i labbås... lita värl ve lever i!
oglundasotarn 2 years ago