FLYAWAY

Correction. Four lamps are in series. I said 3 in the video at one point.

I just measured the RPM of the spinning magnet. Its honking on at 515 Hertz or30,900 RPM !!!

I am making another video where I will show a larger magnet fixed to a shaft . The shaft will be driving a spinning propeller. This will show how powerfull this little setup is as I will be hand holding the spinning shaft, magnet and prop. Only skin bearings! If thats not enough for anyone interested in motor building then if you look further The setup "WITH" spinning prop also acts as a generator lighting 5 lamps . Here are the video links to look at:

The Photobucket link where take you to the circuit info needed to build this device.

http://www.youtube.com/watch?v=MMaEyqsTiHo

http://s1143.photobucket.com/albums/n637/64298/

Category:

Science & Technology

Tags:

• FLYAWAY

[bearpatch626]

how about standing a few of these on end or build them around a doughnut magnet....? maybe mix in some bismuth ? a diamagnetic material... ? XD

[64298]

@bearpatch626  Working on a SMOT motor device right now.

[buddybill65]

I love your videos. I have a few questions. I did not see all your transistors on your schematic. Can you explain? Are you using a relay coil? Where is it located in the video of the circuit? What is attached to the heat sink? Another transistor? Is this circuit a " Stingo" or a bedini" ? Thank you for your time.

[64298]

@buddybill65 Checkout my """Spin Story""" video for all info under the Photobucket link. One transistor used with a small heat sink on it. The L3 automobile relay is inside the aluminum powerbox and you cant see it. On first glance the circuit almost looks lik a Bedini but its not. Bedinis circuit charges batterys. This circuit functions as a motor or generator or both. Take your pick. The device model is small but very powefull.

My next video will be very interesting .Dont miss it.

[buddybill65]

Great work! Is there somewhere I can find a schematic of your circuit or at least something close? Thank you.

[64298]

@buddybill65 I just updated and now you can find a " Photobucket ", link.

Check FLYAWAY video again.

That link has all info for anyone who wants to replicate this device. I quit all my other projects entirely and am concentrating soley on this. The circuit acts differently than any other I have experimented with. You mighr want to buy yourself an expensive clamp meter that will take low DC CURRENT readings . After you finish building it just try testing with different multimeters.??

[mikrovolt]

The fly away when used with an optocoupler could compare rpm to standard AC sine.

this bridges the gap that digital is not doing with narrow dc pulse and partial longitudinal

and other complex waveforms. in short the devise does to magnetic what avramenko does to high voltage. Because you can dial in ac input to match

an unknown exotic pulse.

[64298]

@buddybill65 Wire is one coil made of "TWO" twisted solid strands #24 AWG copper wire. Wire is color coated with a PVC covering. Its called "cross connect" wire. Buy a 1,000 foot plastic spool of it on Ebay and cut off enough wire untill you can measure 19 ohms through one of the wires. Since you will be cutting two wires at one time the reading will be the same for the other wire. Whala-- you have your coil wound the same as mine.

[buddybill65]

Hi, I'm new to this. Can you explain to me your coil of wire? Is it solid or stranded? Is it one coil or two? what guage is it? Thank you.

[64298]

@abbaar Multiple coils each with one magnet linked together on one shaft is a possibilty.

The frictionless shaft that you mentioned wont due as if you make a motor and reduced its speed abrupty the shaft would break loose from its magnetic moorings. Possibly fly into your face at ultra speeds.