TEST TUBE GENERATOR.MPG

This is a spinoff from my previous video SPLISH SPLASH . Now I am spinning a 1/2 inch sphere magnet inside a plastic test tube. The magnet is much smaller than the 1.5 inch magnet I used previously and my light is a lot brighter now. Just my inserting the spinning magnet inside the tube into the core of the coil the lamp will stay lit all the time.




I just decided to run a input output DC power test using a clamp type DC amp meter so I would not make direct connections into the circuit.
Here is what I found: WITH THE LAMP LIT AND POWERED BY THE CIRCUIT.
iNPUT DC voltage 12 volts. Current measured with the clamp meter was.08 amps.
OUTPUT DC voltage measured across the lit lamp was 27.52 volts
Current measured with the clamp meter was.10 amps

.96 watts INPUT and 2.752 watts OUTPUT measured across a 5 watt lit lamp ?????????????
Thats the case but in time my battery supply voltage goes down as explained below. The above figures show overunity?? Who is sharp and has an answer for this??
So what we have here is a 5 watt 90-220 volt AC LED lamp driven by less than a. watt of power from a small 12 DC battery source.
through the below items.

The setup is: The power box circuit, A small 12 volt battery, The coil, A plastic test tube with a 1/2 inch sphere magnet inside. Not forgetting the 5 watt LED lamp.

At this moment it has ran 17 hours 40 minutes straight without signs of quitting. I stopped it at that time. Took a battery voltage reading after 10 hours 40 minutes-- Noted 10.60 volts. After 17 hours 40 minutes -- Noted 6 volts and the setup was still running on that low voltage!!!! Did not want to kill my 12 volt 4 ampere hr battery so I stopped operation at that time and recharged the battery.

Lots of light in the meantime filled my bedroon all night long. Very little spinning magnet noise. Wander if some outdoor equipment company is interested in a portable camper light? I have not seen any commercial units delivering anything near as what light this setup does for such a long time frame.

Check my SPLISH SPLASH video for all building links about this circuit.
http://www.youtube.com/watch?v=RXYDtoqenu8

Since I already know how to build this I have decided to sell everything you see here. Excluded is the 12 volt battery, multimeter, and my wall connected 12 volt power supply I have taken this as far as I know how. Here is a chance by an industry or individual to take it to a new level without having to scour the internet for parts to build it. 8/3/2011 $ 250 Paypal buys whats described above. You pay shipping to where you are.

Category:

Science & Technology

Tags:

• GENERATOR
• SPHERE MAGNET
• TEST TUBE

[64298]

Send me your E mail to 65t@comcast.net

[rostit420]

This is all still measured incorrectly. Overunity is not possible. Your fabricating skills are very good, I wish you and other talented people like you would stop this waste of time and put it toward improving efficiency and learning the proper ways to measure your ideas. Your DC amp clamp is not correct because this is not true DC. All your measurement methods are incorrect. This is a shame, because you have some great ideas, but you are looking into the sun instead of harnessing it.

[64298]

@rostit420

I have moved on and am now concentrating on a WORKING SMOT like motor that runs continuously.

Dont need any testing to at all as the model is very powerful and not only will it turn continuously it can power other devices. A quantum leap from what i have been doing. Hope to post all when I dress up my model for presentation. It can run untill both magnets loose their magnetic power or untill the earths gravity stops functioning. Yes its not perpetual motion.

[AUTS4U]

Very cool!!

How can I get a hold of you? I don't know rules? I would like to talk to you.

[64298]

@AUTS4U Send me an email  65t@comcast.net Mention AUTS4U

[overunitydotcom]

Hi Tom,

please retry the measurements by replacing the LED bulb

with a 275 Ohm 5 Watt resistor and see, if you get the same voltage and current on it.

Also use a low pass filter at the 12 Volts DC input to measure the input current.

WIll be interesting to see, if you will get the same measurement values.

Also do you get more power out, if you put the magnet ball inside the coil

or if you put it ontop your coil ?

Many thanks.

Regards, Stefan.

[64298]

@overunitydotcom Working on the SMOT loke motor device presently.

[4323michael]

Hi Tom, I would like to talk to you about this. would you please e-mail me at MJEdens@yahoo.com. Thanks mje.

[Sumermagor]

hello friend, could you help me find the same effect? i would need some help in my experiment. how can i speak with you?

[bennjanse]

Is the spinning magnet rotating while spinning - if not, what i`m thinking is : if you build a small coil with a spinning magnet inside as a unit, then place the unit onto the big coil, so that the big coil do the spinning work, one can capture xtra energy from the little coil as well as the big coil ?