Tomi PMSquare SMOT design Magnet ramp acceleration

http://www.overunity.com/index.php?topic=4428.0.html

Stefan Hartmann of overunity.com shows
a permanent magnet is accelerated inside
a special permanent magnet track with 90 degrees iron core pieces to conduct the magnetic flux asymmetrially away, so it can leave the track and have a rollaway.
Could also be well used for a SMOT track.

Category:

Science & Technology

Tags:

• free
• energy
• SMOT
• TOMI
• PMSquare
• magnet
• motor
• ramp
• overunity
• selfrunning
• device
• Tarial
• Kapanadze
• Replication
• SR193
• english
• subtitles
• solar
• wind
• power
• Tesla
• longitudinal
• wave
• next-energy
• KW
• Watt
• hho
• save
• fuel
• watercar
• run
• on
• water
• atom
• fossil
• antigravity
• ufo
• kapagen
• naudin
• jlnlabs
• fusion
• sparkgap
• coil
• TC
• teslacoil
• high
• voltage
• telluric
• current
• Stubblefield
• Bedini
• perpetual
• motion
• perpetuum
• mobile
• efficient
• Joule
• thief
• earth
• battery

[overunitydotcom]

>Ok Stefan thank you very much. But it's not >clear for me the position of the differents part

Just look at the endpieces of the iron cores.

These are just 2 legs of iron plates 90 degrees apart,

like bending an iron bar 90 degrees.

These are between each 2 or 3 magnets to conduct the

magnetic flux asymmetrically away from the track.

Regards, Stefan.

[megaverse]

boy is this guy retarded or he just don't know how to make a movie ...damn it could of lasted like 14 seconds instead of 1:14m. anyway we all seen the point

[overunitydotcom]

As I said, this were multiple tries

pasted together.

I just wanted to have it all on tape.

Just to make a 14 second moviewithout looping would have been too short...

Yes,I know, my voice is annoying, so just watch it, by muting the audio volume.

[maryyugo]

Yup. By replacing the magnet at the start of the SMOT against the force of the magnetic field, you are giving it all the energy it needs to make another run. Your hand, not the magnets, are the source of the energy expended during the run.

Overunity doesn't require someone's hand!

[overunitydotcom]

If you put it in from above about 1 or 2 inchs away from the entrance then there is no stick spot, but of course you have to lift the roller magnet up,

which also needs energy.

Just try this out with a roller cylinder made

out of iron, then you can build several tracks

after each other and the roller iron cylinder

should go through it.

( or just use a iron ball bearing as the roller)

[clintautin]

i put the lotion in the basket.....

[chickenpoper]

@overunitydotcom Your voice is not annoying. Your accent is cool.

[theonethatgoofs]

if you make this climb high enough out of the magnetic field a track will drop it infront of the push set agean . but a track for the mag in hand would require wheels on the magnet inorder to go around curves to start using gravity

[1BustedMyth]

Painfull to watch

[AmishSpaceNavy1]

Ok, you can put as many of these in a row as you want, but as soon as you make it loop around to the first one again it will stop. If you start it rolling like this it will have only that same surplus of energy to fight friction - then it will stop. Energy = potential (Gravitational and magnetic) + kinetic.

[agband]

This accomplishes nothing more than putting a paper clip near a magnet and watching it accelerate.

[drackcurico]

haaa