Floor Boar Laminate Cutter

Roberts Consolidated Industries is proud to offer the new FloorBoar Laminate Floor Cutter. This patented cutter does not produce any messy airborne dust and uses no electricity so it is perfect for cutting laminate in any area including new construction. The FloorBoar is lightweight, portable and can be used right in the same room you are installing the flooring in. There is no need to make time consuming trips outside to cut your flooring.

The FloorBoar works with all brands and can cut planks up to 12mm thick to any length or angle, including full length cuts. This versatile cutter can even cut laminate planks that come with the padding already attached.

The FloorBoar features a unique easy crank and cut design with a ratchet action handle that continuously feeds planks into the dual blades. The extended handle provides increased leverage to make it easier to cut through thicker planks and planks with pre-attached padding.

Category:

Howto & Style

Tags:

• Laminate cutter
• wood floors
• cutter
• laminate flooring
• wood flooring
• pre-padded flooring

[poohbear3626]

table saw much easier and only cost 100 bucks

[qepcoinc]

@poohbear3626

While the table saw is the traditional way to cut laminate, the FloorBoar requires no electricity and creates no dust making it a better indoor alternative.

[Graeck]

@qepcoinc This floor boar thing also makes TERRIBLE cuts! It doesn't really cut actually, it "chews". I've been trying to use one today and on every 3-4 cuts I do it chips some of the laminate layer off the board far enough that many of the boards became unusable .. others fortunately I can reuse when I need smaller pieces.

[qepcoinc]

@Graeck

Although the cut is not as smooth as a typical table saw cut, it is ideal for a floating floor installation. When installed properly, all Floor Boar cuts will be placed against the wall and covered by the decorative molding (baseboard or quarter round) used to hide the necessary expansion gap along the floor perimeter.

[ChokoPitbull]

oh god that length cut looks exhausting!!!!

[Coerlin]

Very nice - I'll be doing this early next year and wasn't looking forward to the noise and mess (we live in a terraced area, direct neighbours) - plus - and I kid you not - we've had 20 packs of laminate flooring in storage for over 5 years heh. As for rough cutting, that is to be expected by such a mechanism.

[orsinpat]

good thing is face was hidden the whole time....

[Moe7133]

If you're going to be a professional laminate installer, use professional equipment. Don't use junk like this. Table saw for ripping and Miter saw for chopping. If your going to cut little Notch, just use a Multi-Max. Pro's should have these equipments! Sawdust all over the place then you should have brought a Wet-Vac and Broom!

[ekim1erikson]

@Graeck

And I don't know about you but when I used mine I about got repetitive motion syndrome in my arm from "ratchet, ratchet, ratchet!!!" And it TOTALLY made a mess (I agree) There's plenty of other shears out there that will cut cleaner and save you HUGE time not having to hike your product outside to your saw and back and forth. I rented one at Depot called a magnum shear and it was SOOOO much better!. Only thing was corners but the boar didn't go a good enough job anyway. Junk!

[ekim1erikson]

@Graeck

And I don't know about you but when I used mine I about got repetitive motion syndrome in my arm from "ratchet, ratchet, ratchet!!!" And it TOTALLY made a mess (I agree) There's plenty of other shears out there that will cut cleaner and save you HUGE time not having to hike your product outside to your saw and back and forth. I rented one at Depot called a magnum shear and it was SOOOO much better!. Only thing was corners but the boar didn't go a good enough job anyway. Junk!

[magdalenagalinska12]

get good table saw and industrial vacuum cleaner and also this job will be dust free, but yours cuts it will go x10

[chavez9mm]

and you're going to cart a table saw to a job are you?