American Universal Saw Bench
Loading...
Loading...
513
views
Loading...
Uploader Comments (inwoodcutter)
see all
All Comments (8)
-
I see. My saw is going to be the do all saw in the garage, as soon as I get the fence from Arthur Fuege. I've got a loaner motor on it right now. I've been looking for an old GE or a Howell to run the saw, you wouldn't happen to have any spares, would you?
Loading...
4:18
Elektra Beckum PK200 Table Saw Motorby OllyPJ5,319 views- 1:39
American No 1 Variety Saw Benchby inwoodcutter7,425 views
- 4:43
Homemade table sawby Matthiaswandel132,894 views
- 1:59
Box joint machining on a Oliver 270-D with the sliderby inwoodcutter4,486 views
- 1:02
Tannewitz sawby inwoodcutter5,902 views
- 4:16
Unknown antique planerby inwoodcutter21,304 views
- 8:28
Petite Roubo 1 of 3by PenultimateWoodshop4,146 views
- 1:03
LOGOSOL TIMBER JIG -portable saw benchby ThePhil195212,378 views
- 4:52
16" JA Fay & Egan jointerby wconstructionco517 views
- 0:55
stationary engine Lister D 1937 hard working on 1948 circular saw benchby Vuffira1,451 views
- 4:05
Antique Machinery Festival Kent Connecticutby howielfa1,492 views
- 4:26
Walker's Sawmill Part III - 1915 Porter Jointerby ServiceSpider3,010 views
- 1:18
Jenga pistolby Matthiaswandel2,396,927 views
- 2:06
DIY sliding table panel sawby luminaire2933,870 views
- 4:07
Laguna Tools Driftmaster Fenceby LagunaTools31,420 views
- 0:27
Roy Underhill and the Barnes Treadle Table Sawby ANFaith18,442 views
- 9:59
Shop made Miter Fence - Accessory for the Super Sledby EagleLakeWoodworking140,394 views
- 6:34
Tablesaw Universal Fence Jig Part 1.mp4by numnumbirdynumnum2,043 views
- 1:48
Turning Pewter, rare Tradeby mammoth91195,022 views
Mine runs about 2450 so I can put the 20" on when needed. Have you ran any 12" blades on it? I'm a little concerned with the rim speed on my dado set mostly in plywood and laminates.
morpheusduvall 3 months ago
@morpheusduvall I've only run the two blades that are on it so far. I have two other table saws set up currently and one I leave a 12" solid (not stack or wobble) dado head on. I also use the pin router for a lot of my dados and rabbets. I almost never use plywood or laminates. I work almost exclusively with hardwoods.
inwoodcutter 3 months ago
I like the linkage for drawing the sliding table out, my Oliver requires you pull it out by hand. Whats the arbor speed, about 2900?
morpheusduvall 3 months ago
@morpheusduvall I did the calculations once. I think its somewhere around 2600. The motor is a 1200 rpm and the pulley is roughly twice that of the arbors.
inwoodcutter 3 months ago
How is it that one of those blades is as shinny as a mirror?
73SDR 9 months ago
@73SDR The shiny blade is basically new. It's a Freud ripper that hasn't seen any miles. The other blade, the cross cut, is an older one with a triple chip grind.
inwoodcutter 9 months ago