Bad Methanol Injection Instant Fitting
Loading...
Loading...
2,612
Loading...
Link to this comment:
Share to:
Uploader Comments (kletkea)
see all
All Comments (6)
-
If it does it with a nozzle on as well then definately up the shoot, what brand was it and what did you replace with.
I recently found out quite a few of the water/meth companies share parts.
-
How long have you had your methanol system installed for? Do you like it? Do you have to refill the tank all the time? Thx
Loading...
- 0:21
Audi S4 stage 3 with methanol injection and 22 lbs boost.by bmwm3guy3,636 views
- 2:06
They've used water in their enginesby hypnow409,091 views
- 0:18
Water Cooler Bottle Methanol Fireball (Mad Physics)by madphysicsdotcom321,370 views
- 1:45
1200HP+ 20B RX7 FD Twin Turbo GT35R Methanol Free Revby Parag0n99,969 views
- 5:17
CMGS methanol injection controller EGT setupby coolingmist3,007 views
- 0:28
Duramax water injection burnoutby nwc198694,941 views
- 1:37
GTI MKV water/methanol injection (home built)by justinbimmerman5,090 views
- 0:33
2007 Mustang GT with 15psi whipple and Meth Injection, 5-speed autoby crezzymanlt5,696 views
- 3:32
FUBAR METH ADDICTION KILLS DIESEL MOTORby powerstrokehelp24,590 views
- 0:54
Water Injection Test: Civic Supercharged at 9psiby GorpoBR23,231 views
- 0:22
Cooling Mist Meth Injection, with checkvalveby BigTomRS41,325 views
- 3:49
How Water/Methanol Injection Works & How It Makes Horsepower in Gas Enginesby AEMpowerTV76,477 views
- 5:53
Snow Performance Install part 4 of 4by ParleysDiesel13,683 views
- 0:12
Snow Performance Water Methanol Status displayby TheMunky1135,750 views
- 0:23
BUZWGN 390rwkw 520rwhp Self Built - Bridge Port Turbo e85 fuel + Methanol injection! 24-25psiby buzwgn4,428 views
- 0:31
SMART Car's Custom Water / Meth Injection Systemby littodevilish1,273 views
- 0:20
Water injection plenum view through sightglassby dpsf197218,494 views
- 0:47
Run Your Car On Water - Hydrogen, Proved By mythbuster guys!by Thechoice1products150,327 views
- 0:54
Dyno run at 6psiby flovian35,528 views
- 1:44
AlcohoI Injection Systemby BLOWN2876,545 views
Just a quick thought.. Is the tubing cut perfectly squared and deburred
alan14b 1 year ago
@alan14b It's not the tubing... I can swap on a different fitting of the same type to the same tube and it will seal up just fine. Trust me... I thought the same thing.
kletkea 1 year ago
The connector can't hold back the pressure the pump can supply, but it would never be blocked, does it still do this with a nozzle connected releasing some of the pressure.
pimppulsar 1 year ago
@pimppulsar Yes! It still does this when connected to the nozzle. Whether the end is blocked or not It should still be able to seal and hold the pressure of me blowing in the end of the tube. I confirmed it was a bad fitting by replacing the fittings with a different manufacturer's fitting and it holds pressure without leaking just fine. These fittings are designed for use in Pneumatics, where pressures are normally in the 150psi range. I don't buy the thought that they can't hold back pressure.
kletkea 1 year ago