HHO Low Voltage HIgh Amperage
Loading...
Loading...
4,562
Loading...
Uploader Comments (abangjkt)
see all
All Comments (7)
-
you made it bro !!!
-
I would like to know how many watts is the source and is connected directly to an outlet or voltage stabilizer,because when I connect to a source ATX stabilizer and a half, marked only 2 amps at 5 volts from the line, you better connect directly
-
is that all bubbles come from cell ? thats alot !
-
That's Creative!!
Any ideas on MMW??
Loading...
3:01
High Current Transformer 1.6v @ 800A MOTby sparkie2111,839 views- 1:51
My new hho drycellby hydrogenfever33,076 views
- 10:00
high output low volt hhoby NOBOX712,011 views
- 5:40
HHO Hyper Drive Part 1by bartley4407,636 views
- 2:01
PWM 50 AMP with frequency ajustableby 358bruno18,044 views
- 1:44
my latest hho generator design.prototype.by eccentricgasman19648,911 views
- 0:38
hho under pressureby calamia135,621 views
- 5:57
efficient hho generator new designby reddevil25764,060 views
- 4:48
HHO system install in Mercedes-Benz 4V 40 Ampereby SimonG289212,363 views
- 0:46
LOW VOLTAGE HIGH CURRENTby Mnermal16,839 views
- 4:19
HHO Dry cell on a dietby hhoforvolts2,398 views
- 3:33
HHO Generator Alternator, like getting FREE POWER FROM YOUR ALTERNATORby alternatorman25,241 views
- 4:39
Low Voltage, High Amps, Here are the Results..wmvby HHOPWR2,392 views
- 2:49
HHO Machine with a compressor of a freezerby hgfrind71,195 views
- 2:22
Pure voltage No amperage + Skin effectby Zer0PointUnlimited1,982 views
- 1:43
HHO Gas Applicationsby waterflame00720,876 views
- 7:25
1987 Dodge Merry Miler RV Conversion to HHO Completeby mrjamestferguson1,439 views
- 10:16
HHO High Voltage 140 - 2500 Volts and Arc Welding Device Part 2by pjckac12,560 views
- 1:16
Microwave Oven Transformer MOT Modificationby water2gashawaii11,617 views
Koh is electrolyte to make the water more conductive, it does not prevent current run away. Use of a PWM will prevent it.
soldiersofmercy1 2 years ago
I know. What I mean to control the amperage was to raise the amperage by adding KOH until 20A. Conductivity of distiled water is < 10 microsiemen/cm, which is hard for electricity to flow. K (potassium) is positive cation ion and OH is negative anion.
That's why the title of this video is low voltage high amperage... :). anyway thanks.
abangjkt 2 years ago
Excellent video using low voltage high current. If your gap voltage is around 3.5 volts, that means you need a stronger PC power supply. However right now your voltage is a the top of the safety range of 2.5 to 3.5. Get a bigger PC supply 450 Watt or higher and if you are using 120vac mains turn the switch to 240vac and that will give you around 3.4 v high current using the 5v red wires. If you are using 240vac like in Europe, then use the 3.3v orange wires.
Good to see you know not to use 12v.
hhoforvolts 2 years ago
thanks for comment. I'm not going to to use PC power supply to drive the cell. This is just for test. Next step is to set up the cell into my car. I'm now building the electronic voltage regulator 0 - 12V @ 25A (or 30A), input 12V from car battery. I already ordered the electronic components and I hope next week I can test it using that. I also make the container for the cell complete with the bubbler, so i can check the gas production in LPM. I checked your video and it inspires me.. thanks. :)
abangjkt 2 years ago