3 joystick futaba 9c for FPV
Loading...
Loading...
27,578
Uploaded by 3rflyingcom on Feb 2, 2009
I have designed a system to work with the Futaba 9c that allows the VR-A and B knobs to be quickly replaced with a 3d joystick for use with FPV pan and tilt systems. The 3rd joystick can be removed and the radio will function like stock in about 10 seconds.
I can retrofit your futaba 9c for about 250 dollars if you are interested.
I can build you this pan and tilt system for about 65 to 70 dollars.
Just send me a message.
- 37 likes, 1 dislikes
-
Link to this comment:
Share to:
Uploader Comments (3rflyingcom)
see all
All Comments (21)
-
Genius!
-
Good job!
-
'
wow that is cooool 3 controls
-
That is so sick :D
-
@3rflyingcom yeah that is what i tough thanks for the help im gonna see if i can find some cheap Chinese JR imitations
Loading...
- 2:01General-view.com Rescue Drohne beim IKAR-Kongre...by cbaer100013,186 views
- 0:53Rotating beaconby fertred4,448 views
- 5:52RC FPV Kit HobbyKing 900MHZ 200mW Tutorialby sfabiom42,414 views
- 7:58Easystar FPV -- Dual RX Diversity Testby ACMEFPV30,587 views
- 9:59My FPV Easy Star and the modificationsby petleh8242,341 views
- 4:02Futaba Hack Module How-To in 5 minutesby numnutchris1,577 views
- 9:28My New Futaba 10cby RLC10150,048 views
- 0:42GoPro Hero Pan/Tilt Test for my EasyStar FPVby dworkma5,247 views
- 7:37First FPV Flight with a Joy Stick Controller Ap...by FPVFLIGHTSCHOOL163,299 views
- 0:23RC JetJoe 1200 Turbine Engine Carby michaelpk3304,632 views
- 2:29High Qualty FPV testby 3rflyingcom3,000 views
- 1:33◄1►ground station fpvby Sacha21110,180 views
- 4:43Flycamone copterx boom trex 450 3d FPVby marty1200418,007 views
- 1:42USB to PPM Generator Test-1by Touchbiance7,183 views
- 4:21New Concept Heli 2nd Test flightby alishanmao503,841 views
- 9:03AXN Floater FPV 2kmby b3nny3314,741 views
- 4:00FPV Flight with a Joy Stick Controllerby FPVFLIGHTSCHOOL29,446 views
- 4:36eagle on steroides. NORWAYby badasspython193,520 views
- 1:49Futaba 6EX converted to 2.4Ghz (Assan 8X)by rosiris314,598 views
dou you have a picture of the wiring work?
by the way, I am trying to figure out how to connect a headtracker without the trainer port because that is taken by my long range system...... what I was thinking is replacing one of the VR switches with the wires from a headtracker, but that didn't work for me, probably because headtracker was nog getting enough power from the switch wiring. though I tried to power it separately, , that didn't work either. Can you give directions? Thanks!:)
DrDimk0o 6 months ago
@DrDimk0o
I do not
I doubt the head tracker outputs a resistance signal (0 to 5000 ohms) That is why it wont work with a vr knob. A vr knob only sees resistance if you go and apply a square wave or some kind of voltage to the vr knob circuit that might only accomplish damaging something.
3rflyingcom 6 months ago
@DrDimk0o Right.. didn't think about that :) besides I found a solution - just wire the two together. Headtracker will use PPM in and long range system uses PPM out and both have same power and grounding. :)
DrDimk0o 6 months ago
@DrDimk0o
aren't you using both at the same time? wont this cause a conflict?
3rflyingcom 6 months ago
where did you got that joystick par number or supplier retailer any thing !! i had being looking for it for a long time but i cant find it
ptacnik1988 1 year ago
@ptacnik1988
hey bud its just a joystick from a standard R/C controller. If you have a old controller laying around just pull one of the joysticks out. I believe they all use 5k ohm potentiometers...There might be some 2.5k ohm ones out there too...The 5k is most desirable for use on the futaba.
3rflyingcom 1 year ago