My AFR Headed 355 Chevy Race Motor

Its a 355 Chevy small block with Aluminum AFR 210 eliminator race heads, comp roller cam, j&e pistons, super victor intake , a 1050 holley dominator, and a nx nitrous plate system

Category:

Autos & Vehicles

Tags:

• race
• motor
• afr
• eliminator
• heads
• camaro
• chevy
• 350
• 355
• roller
• nos
• 1050
• dominator
• nx
• engine

[love77love1]

i am thinking about getting some afr aluminum heads for my 406 small block but i do not know to much about them could you give me some advice on a good company to go with

[Z28RaceFreak]

@love77love1 afr is the best head out of the box for the $. I got mine from summit. u cant go wrong with afr heads... check

[Z28RaceFreak]

@love77love1 check around 4 the best price, summit will beat it..

[ThugLife383]

hey man can you please tell me whats your set up like compression ratio,cam specs,,etc ?

[Z28RaceFreak]

@ThugLife383  11.5 to 1 comp, cam is 649-649 268-278 @.050 110 lobe sep. installed at 106.

[01xvortec]

did you build your 355 off a magazine article from car craft?

[Z28RaceFreak]

@01xvortec no

[AKIman522]

@Hysjulien69 350 chevy bored .030 over stock 4.000" bore to give 4.030" bore. Stock crank @ 3.480" throw using stock rods @ 5.700" long. That equates to just barely over 355 cubic inches. Like 355.42 cubes, or something.

[Hysjulien69]

what is a 355? like originally, and wat do you have to do to make it a 355

[paintonmyhands]

MIGHTY MOUSE!

[dsm525]

Nice motor, How you like the 1050 on there? Have you tried smaller, and tested them?

[TheDustikus]

@9F1F1A A 355 is simply a 350 that's been bored .030" over, the increase in cylinder bore adds 5 cubic inches.

[9F1F1A]

how do you make a 355 chevy smallblock?

[cbr900rr919]

@thvlajan you can run cast pistons with nitrous as long as you have the timing right i.e a timing retarder. compression will hurt to as how much you can spray in it. get a good nitrous controller if your going to be spraying at that high a compression. and maybe a two stage nitrous set up so you aren't spraying it all at once.

[NickColcord]

what was your e.t at the track?

[thvlajan]

nice vid: quick question. ok those are J.E 11.5 to 1 comp pistons right are they flat top or dished piston. reason i asked because, Im rebuilding my Monte SS 350 w/ i-con forged pistons 4 valve relief +30 over with a compression of 13 to1 is it possible i can use nitrious with those piston? reason i asked becuase when i check on ebay at the same spec pistons but from speed pro it was said "Not recommended for use with nitrous" im also using AFR 210 heads as well.

[thvlajan]

nice vid: quick question. ok those are J.E 11.5 to 1 comp pistons right are they flat top or dished piston. reason i asked because, Im rebuilding my Monte SS 350 w/ i-con forged pistons 4 valve relief +30 over with a compression of 13 to1 is it possible i can use nitrious with those piston? reason i asked becuase when i check on ebay at the same spec pistons but from speed pro it was said "Not recommended for use with nitrous" im also using AFR 210 heads as well