How to Remove a Stuck Case
Loading...
Loading...
2:32
bullet puller trickby Rokn46021,769 views- 1:37
Using the Lee Factory Crimp Dieby TexasStraightShooter24,908 views
- 5:16
Removing a stuck case from a reloading die (HD)by gavintoobe11,078 views
- 0:27
Lubricating Cases Using Lee Resizing Lubricantby LeePrecisionInc7,041 views
- 8:52
Consistent Crimp-Lee Styleby brshooting6,697 views
- 4:14
Basic Reloading: Priming Issuesby ammosmith103,623 views
- 0:43
Lee Precision Case Bulge Removerby msinsabaugh4,581 views
- 3:33
Bullet Pulling on the Flyby ammosmith14,996 views
- 0:57
Removing a cast bullet stuck in a moldby magmaengineering6,055 views
- 5:39
Building a reloading bench, mounting Lee Challenger press kitby TacticalAdv39,551 views
- 1:56
Stuck Bullet - Thompson/Center : World of Muzzleloading Chapter 8by TCArmsCo2,006 views
- 10:03
full length and partial full length resizing brass.AVIby greghud2,094 views
- 6:38
100 rounds on a Load Master in 6:37by DarwinTe65,917 views
- 13:29
Shooting Techniques Part 3 [ Trigger Control ]by hickok4578,570 views
- 0:52
Camdex Case Processor Part 1by EvergladesAmmo2,665 views
- 5:40
Basic Reloading: Sizing Pistol Brassby ammosmith15,714 views
- 0:53
Reloading 9mmby JohnVH54128,922 views
- 0:34
Installing Lee Rifle Sizing Dieby LeePrecisionInc4,976 views
- 1:24
Pulling Bullets From .223 Brass with Hornady Cam Lockby Free2Reload13,951 views
- 2:39
Using the RCBS Chargemaster 1500by aaronmj73,946 views
ahh now I look and see how, sigh, I should'a watched this before I butchered my case and then the die.. Beware the primmer steel tip if its bent, it don't bend back just snaps off. Oh well live n learn. Heaps of one shot lube no great force applied just a unlucky noob and a wonky sticky case. Thanks the post it worked well but the damage was done...
derwoodii 5 months ago
I just removed a stuck 5.7 x 28 case utilizing your method. I have been loading over 21 years, & this is only the second case I have ever stuck. The 5.7 has a coating that accumulates in the die, & can cause problems, if you aren't careful. Thanks for posting this, it saved me a trip to Missouri to pick up another die set.
kbaughman100 9 months ago
I have a stuck case that no amount of striking with a punch and hammer will get it unstuck. So far all I have managed to do is smash the expander decap retainer into 3 pieces and bulge the primer housing out of the bottom of the case. any suggestions?
RoninNZL 10 months ago
Thank you this worked great.
I was loading up some .223 last night and accidently raised a clean and tumbled case into the siziong die when I was going to prime with the safety prime. Needless to say it got stuck..
I was looking online for a stuck case remover when I ran across this video.
Just tried it and I got the case out in just a few seconds and now I'm back in action. Thanks again....
hbbrdjff 1 year ago
This worked great for me. I stuck two cases today on my first day of reloading (Ever). As mentioned by one of the previous comments, I didn't use enough One Shot case lube! Thanks!
magnetbug 2 years ago
your a life saver
dills2403 2 years ago
They sell a stuck case remover. More or less you drill down the case from the top. Then you tap the hole and use this spacer and bolt to just pull it out. I did one today it worked great. I do not like how they are hitting the rod, but it looks to work. The case remover was $25.00 and less chance or messing up the die. That is what I think anyway.
Tgreenmi 3 years ago
Thanks. I was trying out Hornady One-Shot case lube and evidently I didn't use enough. Your method worked well.
Mark45414 3 years ago
I got one stuck this morning. I ruined my other resizing die two weeks ago.
woolygator 3 years ago
yeah so do I except I have a RCBS die and I can't figure out how I'm going to get the stupid thing out! Any suggestions?!?
kussoff1 3 years ago