Rotary and Slide Carbs on Nitro Engines
Loading...
Loading...
895
views
Loading...
Link to this comment:
Share to:
Uploader Comments (jthornley12)
see all
All Comments (15)
-
@jthornley12 ok. sealant in the front shaft bearing?
-
@jthornley12 thanks for response. but how i can put gasjket sealant? i have to make a video! thanks anyway
-
@xXzipbladeXx The Screw that holds on the carb :) it is a long screw that goes in one side and has a bolt on the other end.
-
@jthornley12 what screw ??
-
@xXzipbladeXx Remove the Screw all the way, then let the bolt fall out :) the carb should come off easy then
-
i need help taking my carb of it has a bolt threw it with a little nut on the end and cant get it of to clean it can you help .
Loading...
- 1:32
Adjusting the Carb on Your Nitro Engineby jthornley123,163 views
- 2:03
RC Nitro Rear Exhaust Removalby jthornley12641 views
- 6:37
Low Speed Needle Tuning of your Nitro Engineby jthornley1244,370 views
- 4:57
How To Tune a Nitro Engine VX 18by jthornley1211,760 views
- 8:25
Cleaning n Fixing the Nitro Engine Carburetorby alishanmao46,084 views
- 1:36
Traxxas setup 10 of 21 - Setting up the Carburetorby yoyoman2k1122,853 views
- 2:00
O.S. Engines 30VG(P) ABL 21E Slide Carburetorby RCislife871 views
- 0:27
SH .18 Nitro Engine Start Up (Drill Starter)by MrBreadboard852 views
- 3:53
Re-positioning the Carb on Axial Nitro Motorsby axialvideos10,755 views
- 0:52
Test Run - Twin Rotor Nitro Rotary Engineby Mini13B67,803 views
- 5:43
RC nitro engine Stock Needle Settings- Vid 2 How to Tune Seriesby Squirrelod130,877 views
- 1:45
CTR 5.0 Nitro RTR Sedan - 90+MPHby CENRacingUSA40,939 views
- 7:29
RedCat Nitro Engine Tuning Guide Pt 1 -- Basicsby alishanmao11,787 views
- 4:43
Nitrorcx Guide: How to Clean the Carburetorby nitrorcx31,044 views
- 10:00
how nitro engnes work (for Nickgarage)by highdeserthater4,217 views
- 3:22
How to Replace RC Pull Start with Power Starter Drill Starterby jthornley124,563 views
- 2:44
Nitro engine Carb opening gap & idle screw demonstrationby jthornley124,025 views
- 5:11
Understanding Carb n Tuning the Engineby alishanmao45,299 views
- 2:13
How to tune a carb on a nitro truckby NewwebProductions107,951 views
hey! i found a air leak in front shaft bearing is that normal? maybe that's the reason is running lean
Pellogt 4 months ago
@Pellogt No air leaks are normal :) use some sealant to solve it. And check all screws are tight
jthornley12 4 months ago
is normal to have a air leak in the boot of a slide carb?
thanks
Pellogt 4 months ago
@Pellogt No, try to fix that. Use some gasket sealant. Also you can try tightening the carb itself, if not then perhaps replace it
jthornley12 4 months ago