Amp repair part 3.avi
Loading...
Loading...
3:39
Amp repair part 4.aviby romi1rome18,209 views- 5:44
Amp repair part 5.aviby romi1rome12,841 views
- 3:41
Amp repair part 8.aviby romi1rome10,230 views
- 1:50
Testing Mosfetsby botronics74,332 views
- 6:13
Amp repair part 2.aviby romi1rome27,914 views
- 7:08
Alternator vs Battery vs Capacitor (Part 2)by romi1rome5,693 views
- 4:46
Amp repair part 6.aviby romi1rome9,691 views
- 62 videosDerrick's Repair Videos
- 2:47
How to troubleshoot your ampby ChevelleSS8,583 views
- 2:45
Amplifier dead? Maybe not!by AyeohG18,920 views
- 6:31
amp repairby jason28w15,576 views
- 0:47
BLOWN AMP (well blown capacitor) time to fix itby chubbawubba5056,398 views
- 5:04
how to install a capacitorby TheSWAGER9755,377 views
- 4:48
Amp repair part 1.aviby romi1rome55,431 views
- 9:05
Troubleshooting to fix an Amplifierby kriskringle3212,558 views
- 14:42
Checking out a Kenwood car audio amplifierby ESRepair11,887 views
- 0:30
Amp w/ blown capacitorby dannysauer3,709 views
- 4:35
Low Voltage to car amp (Part 3)by romi1rome1,220 views
- 3:23
testing a transistor using a volt meter DMM Multi Meter How to check a transistorby shango06641,530 views
- 1:31
Testing For Current Drain That Runs Down Car Batteryby ifitjams213,217 views
- 3:55
Repairing Rockford Fosgate Punch 8" Wooferby AnythingLoud3,664 views
@dlee9900 no
electonixG 2 months ago in playlist Uploaded videos
I have about 9k of resistance. Does that constitute a bad mosfet?
dlee9900 4 months ago in playlist More videos from romi1rome
i have a 750.1 zx kicker .. it worked fine for two years out of no where it cut off came back on a week later did the same thing but this time no sound?. i hooked it back up came on still no sound so i unpluged the subs to try diff ones still nothing.. but with the subs unhooked the amp would just come on an cut off till i pluged the subs back up..where would i start to look for that? maybe the channel is bad? what part of the amp is the channel an how to test that?
jeremy21s 4 months ago
i hav a logic 4channel 1000watt amp i installed it this morning in my car but it always go in protect i check my ground it still goes in to protect but i don't hav ah multimeter to check my voltage on my battery can u help on wat to do if to open the amp or wat? plzzzz an thnx
TheKwesi23 6 months ago
will bad transistors heat up mosfets and blow the internal fuses? the amp starts getting hot in a hurry it goes in attempts to go in to protect
FORDGTFANATIC 7 months ago
Good video, told me what I needed to know although it really need not have taken 3 parts to explain the cause and solution. Thanks though.
sparkyuiop 8 months ago
I Have a 4 Chanel ma audio amp and I Get sound on all chanels but 2 won't get louder why And Can I fix it.can you make a video for that problem thanks
rex2265 8 months ago
I had my amp wired at bridged at 1 ohm & it's only stable at 4 bridged. I fried it after like 2 months of use (longer than I would have expected). I opened it up and noticed that where the ground connects to the circuit board is fried & completely melted through. If I fix the ground do you think it could potentially work again, or did I probably blow something else? I can go through and troubleshoot, but I wanted your opinion first :)
TechOneMN 10 months ago
First i'd like to thank you heaps for your videos, i find them very useful! I know that transistor may have been blowing, but it's probably not a good idea to test it on a conducting material; the case of the amp.
ads861 10 months ago
how do you know what mosfet to use? I checked mine and there shot.
lilpsycho213 11 months ago