Jerry Rosanes 2000 Dakota R/T 408 Stroker

Has KRC performance parts, 408 stroker which I built . 2.08 KRC race heads bee hive springs. KRC 408X cam, F&B 55 MM Throtle bodie, MSD Fast system computer. Also these are test n tune runs just installed system this is the 2nd pull. has a full 4 link rear end I made a custom back half, 20 gal fuel cell under truck. q1a coilovers in back 2" coils with a 3" drop buckets on the A arms in front. Has Sintech mufflers and the five lug Dodge Viper wheels from the car not the SRT-10 truck . 13.5" wide in back 10" wide front 255/45 18 frt 345/35/19 back. the truck put down 380 rwhp and 491 ft lbs torque. it lost nearly 100 hp from the motor to the wheels. Trannys fairly built transco stage 2 shift kit kevlar clutches and has a pdq 2600 stall convertor. Full return fuel system 2000 areamotive fuel pump ect.....

Category:

Autos & Vehicles

Tags:

• dakota rt

[supercharged408rt]

Ya he has his ups an downs so what's ur 1/4 times ?I'm just tryin to see around what my truck will do

[1bad408]

@supercharged408rt I haven't been to the track since the 408 build, but a guy that has the same set up from krc did a 11.90 in a reg cab. I think mines capable of a low 12, since mine is four linked, but I dont have any slicks.

[supercharged408rt]

Ya I like ur truck alot I just got my hole 408 set up in I just need to put it in with ny Paxton nova2000 thinkin bout some spray to it also what u think an krc so u live in fla to?

[1bad408]

@supercharged408rt cool the blower will really make it go. I use to have a kenne bell blower on mine but it only gave it 60hp to the wheels, so I sold it on ebay. mine now has 400 hp 491 tq to the wheels just with the stroker build. About a 90 to 100 drop from the fly wheel. and krc is ok I thought marty was bright but he's gone now. and I live in Washington state.

[supercharged408rt]

Hey where could I get the exhaust mounts like that

[1bad408]

@supercharged408rt I made the side cut outs out of stainless steel. I welded a 4" pipe to the inside about a 6" long piece around the hole so it looks like im running 4" exhaust but Im useing 3".

[PlattLegoWWE]

you really gotta trust your your skills to be cutting out pieces of the vehicle! lol i know if i had a truck like this i wouldnt be trying it! lol Very nice look to the truck though!

[dtofq]

What size spacers do you have in the front? Thanks

[MoparOrNoCar28]

where did you get those rims???

[frodo70444]

hope that smoke was new mufflers breaking in!

[MrPces2008]

Dude, Beautiful truck!! Sounds awesome, like it has some balls!! If you check out my page/video, Im running a 5.7 Hemi in a 05 dodge ram 1500. Love the truck and wont ever part with it.. Still playing with it, not so much done to the engine, but I'm working on it.. i would love to swap it out for a 6.1 Hemi SRT and supercharge it, bet that would cost a pretty penny..lol

[rmindydotcom]

Thats one damn sharp lookin Dak. Sounds like a decent build with a good suspension as well.

Were you having trouble with a B&G flash prior or something else?

Ran 12.9 with my mild 360 & 7psi but had to use a stk pcm to do it which held it back big time. MP PCM & SMT6 wreaked havoc when I added boost. Had to shift 400rpm below where na mtr made peak hp(600below normal shift points)

Replaced everything since then. Expect to run 11.5 without going double digit boost now.

[jerrys1bad66c10]

@JuRaBinks checkmate. but on my other truck I have a gem top low profile and it's the better of the two.

[JuRaBinks]

What kind of tonneau cover are you running

[1bad408STROKER]

@CavScout82ndAA I bought them from john Hennesey Hennesey motorsports. He gets the customers viper and puts the twin turbos on and they want his rims, so he always had rims forsale. And the viper car has always had the 6 lug pattern.

[CavScout82ndAA]

hey where did you get those rims?? website?? if so which one?? i tried finding 6 lug pattern with no luck at all..and i tried looking for the rims off the car with no luck either they show up as 5 lug pattern