Two Years of Bedini Projects

Well, two and a half years technically... I was just looking through all my old photos and clips of old projects and thought it would be fun to put them together in a vid. ^_^

We've got pulse motors, bedini motors, multi coils, solid state oscillators, bedini fans, neon triggered cap pulsers, pulse width modulators... and a couple of my recent unfinished projects!

The large solid state oscillator near the end will eventually be using a 24 strand coil with MJL21194 transistors running on an OCD circuit, but costs are holding it back so at the moment it is still just an 8 strand coil.

and right at the end is something completely different! That is actually just one of two units that will be running the same shaft. Each rotor will 4 magnets and each unit will have 10 stators in 5 sets of two being pulsed out of phase which will give it 40 pulses per revolution. It will be using very low resistance, low inductance coils being pulsed by a homemade pulse width modulator in the khz range. Still experimenting with core materials to use though it looks like it will have to be iron powder because of the eddy currents. Should be an interesting build!

Enjoy!

Music : Daft Punk - Harder Better Faster Stronger from the Alive album.

Category:

Science & Technology

Tags:

• bedini
• motor
• ssg
• pulse
• solid
• state
• oscillator
• cap
• pulser
• width
• modulator

[cloverpark2011]

im confused. i have one Bifilar coil and three with only one guage of wire on it making my project have total four coils of spooled wire with a core in each. how do i hook all of these up to work together and do they all have to be bifilar coils? nice job on your success by the way. i am interested to here back from you since you obviously know what ur doing. if possible can you send me a diagram on how to construct this. thanks

[Mrinfoone]

hi sinse seem like you know just about everthing on the bedini circuit. Can you tell how to connect more than one or up 10 coils to a bedini circuit? Do you to have seperate controllers or can you used the same one. Please very specific if you can helpp thhxs.

[andywalkerplumber]

I wonder if the bedini could be made better using two wheels, one on the other side of the electromagnetic coil, only on that one, the polarity of the magnets would be all opposite poles..or what would happen if two wheels with two northpole magnets were on opposite sides, of the core spinning. I guess there are so many ideas you could play with it would take a few life times to get around to them

[333kgb]

The potentiometer is connected to a 24 gauge outside coil wire. My 1N4007 diode is connected to the positive on the secondary battery. Then the outside 20 gauge wire runs to negative on the secondary battery and on the positive on the primary battery

[UrCoffeeTastesToasty]

NIce Work. Hadn't seen your motors yet, will come again.

Thanks for the cap pulser, had been over many brain breakers (circuits) myself and never been able to find a proper working cap pulser without the gap.

greets,

YCTT

[sdfab]

Man that was really emotional for me . This research has changed my life.Im so glad other folks are beating the same path

[oioioi3000]

Do you have a Cap Pulser Circuit you could email me?

I have been able to charge my Battery to 13.3V while not to badly draining my input and wanted to facilitate continuous input by placing a Capacitor large size to dump back to input now and then please reply soon

[K0W0O0N0]

Yeha, great video man!

Cheers...

[SkeyeDreamer]

you're unbelieveable..... great!  keep going on!!

[melikegolf]

Hi,

I must commend you for your energy and dedication to the "higher" learning. You are obviously driven and are connected to the conscience revolution occuring worldwide.

You are not alone. We must share our knowledge and discoveries for the betterment of all humanity. I am definetly thinking about things differently.

I have lots of experience in electricity and electronics and am currently studying MEG stuff. Where do I get info on Bedini motors?

Cheers,