VW STROKER BUS ENGINE stroker 78mm x 92mm

WITH 5 QTS OF 30 WT ZINK- ENRICHED BRAD PENN OIL.. AND A ENGLE 110 CAM WITH STRAIGHT CUT GEARS AND SOME 110 OCTANE WITH 4 GRAMS OF LEAD PER GALLON. ITS LITE EM UP TIME... THE NEW BRAZIL FUEL PUMP IS A PIECE OF JUNK. ITS WORTHLESS 3-1/2 POUND MADE IN THE USA ELECTRIC FUEL PUMP IS THE RIGHT WAY TO START UP A NEW ENGINE. GUARANTEED FUEL DELIVERY WITH THE FLOAT BOWL FULL.TEMPORARY CLEAR FUEL LINES TO WATCH FUEL FLOW HELPS .. I LIKE USING RACING FUEL TO START NEW ENGINES BECAUSE OF ALL THE LEAD IN THE GAS.. IT LUBRICATES AND KEEPS THE TEMP COOL ABOUT A 100 DEGREES COOLER. ONE SLIGHT SETBACK THE CARB FUELNEEDLE SEAT WAS LOOSE AND WOULD NOT ALLOW THE BOWL TO FILL UP.. A QUICK FIX WITH THE WRENCH AND PROBLEM SOLVED.. I SET THE TIMING AT ZERO STATIC TO START.IM USING AN EARLY 356 PORSCHE DISTRIBUTOR.FOR A NORMAL ENGINE. MECHANICAL WEIGHTS. WORK WELL WITH A ENGLE 110 CAM..THIS ENGINE HAS
THRU- BOLTED CENTER MAINSHAFT, AND AN ADRIAN 5/8 BALL BEARING PRESSURE RELIEF VALVE. AS YOU SEE THE IDLING PRESSURE IS ABOUT 60 PSI. WITH A COLD ENGINE.START UP . IT WILL STAY AT 40 PSI WITH A HOT ENGINE.. NOTICE IN THE VIDEO YOU CAN T HEAR THE TAPPETS.. I NICE FEATURE WITH THE ADRIAN 5/8 BALL BEARING SET UP.. THE TAPPETS ARE BEING FED A TON OF OIL AS IS THE CRANKSHAFT . BUILT TO LAST ANY .STOP AND GO TRAFFIC HAS NO EFFECT ON YOUR ENGINE WITH THIS SET UP. THIS ENGINE IS ALSO RUNNING A STRAIGHT CUT GEAR SET.SINCE ITS A LOW RPM ENGINE I SET THE WASHERS IN THE MIDDLE CAM..I DONT LIKE TO IDLE A NEW ENGINE SLOW ITS BETTER TO HAVE THE RPMS UP A TAD SO THE CRANK CAN SPLASH THE CYLINDER WALLS..WITH OIL .BEFORE STARTING THE ENGINE I REMOVED THE PLUGS AND CRANKED IT UNTIL I HAD 60 POUNDS OIL PRESSURE.. THE PISTONS AND BARRELS WERE WASHED WITH SOAPY WATER ON ASSEMBLY. THE PINS GOT LUBED . I RAN THE ENGINE FOR ABOUT 4 TO 5 MINUTES.. WITH A FEW START UPS .. MAN IT SURE LIKES A LOT OF CHOKE TO START... ITS A LONG WAY TO THE SPARK PLUGS... I ALSO USE GEAR REDUCTION STARTERS WORTH EVERY PENNY THE ENGINE MAKES A LOT OF RESISTANCE FOR THE INN ITAL START UP... THEN GETS BETTER AS THINGS BREAK IN.. THE OIL FILTER I USE ALLOWS ME TO REMOVE THE FILTER AND CLEAN IT FOR RE USE.. THIS WAY I CAN SEE ALL THE SMEGMA ITS CATCHING . I THINK IT WAS OVER A 140 DOLLARS BUT HAS LOTS OF NICE FEATURES..LIKE ITS ALL ALLOY AND ACTS AS A COOLER ALSO AND YOU NEVER HAVE TO BUY A FILTER FOR IT. WITH THE CB 1 QUART OIL PAN IT NOW HOLDS 5 QUARTS OF OIL TOTAL ... GREAT FOR A BUS STROKER ENGINE WORKHORSE.GRUNT MACHINE.WITH THE 388 GEAR SET IT WILL BE WORKING ON THE BOTTOM END. I WILL TEST THIS ENGINE AGAINST THE CROSS FIRE INTAKE ON THE DYNO SOON AS ITS BROKE IN A LITTLE..I HAVE MORE INFO ON THE SAMBA ON HOW THE ENGINE CASES WERE PREPARED. THIS ENGINE ALSO HAS A SPECIAL DOG EAR THRUST FACE HARDENED WASHER MACHINED INTO THE CASE FOR HEAVY CLUTCH WORK. ENGINE CASE PREPARATION IS EVERYTHING .EVEN THE CYLINDER BARRELS ARE TRIPLE CUT ON THE CASE WITH VERY TIGHT CLEARANCES.--ABOUT 2 THOUSANDTHS.PRECISION FIT. THIS ENGINE WORKS OUT TO BE 9:1 COMPRESSION RATIO. PLENTY FOR TODAYS CRAP REGULAR GAS.I ALWAYS USE A LITTLE LEADED RACING OIL IN ALL MY AIRCOOLED ENGINES. MAKES A WORLD OF DIFFERENCE . BRAND NEW ENGINES GET 100 RACING FUEL FOR THE FIRST GALLON OR TWO. THEN WEENED BACK TO 10% THE LIFE OF THE ENGINE. NORMAL DRIVING YOU CAN USE AS LITTLE AS A COFFEE CUP FULL TO GET BY.PER 10 GALLONS.. AFTER A COUPLE OF HOURS OF RUNNING OUT COMES THE OIL CAUSE ITS LOADED WITH CRAP . ALSO A FULL OIL INSPECTION OF WHATS IN THE OIL FILTER. WITH THE STATE OF THE ART MICRON OIL FILTER ON A FULL FLOW SYSTEM YOU ARE LIGHT YEARS AHEAD OF THE GAME.. THIS ENGINE IS NOW A SINGLE RELIEF OIL PRESSURE SYSTEM LIKE THE 356 PORSCHE ENGINE ONLY WITH 100 PERCENT FILTERING OF THE OIL. TOMORROW I START RECORD KEEPING ON ALL THE VALVE CLEARANCES FOR POSSIBLE CAM SHAFT PROBLEMS OR VALVE STRETCH. LEO

Category:

Autos & Vehicles

Tags:

• VW
• STROKER
• BUS
• ENGINE
• 78
• 92

[joelbee1991]

for the hard start up your carburetor probably needs to be cleaned. or your timing is probably to far off. there stuborn to start if the timing is advanced to far.

[puchmanlenny]

@joelbee1991 the points were set at .002 da-------amazing it ran at all..leo

[NickelbackPWNS]

running that high of fuel in that small of a motor doesnt do any good. Also, don't type in caps.

[acrazedmaniac]

fair..ly? wow. love the paint job on the headers.... love how you rev up a cold new engine after making the fuel rich also... did you time the cam in with the wheel? how long did that take you? and how? what are you going to use this for?? (way you have the 'stuff' mounted...)

[bluejay148]

sounds good but timing is off abit

[yami700thumper]

sorry to post this on your video but does anyone know if your have to have an oil pressure relief valve installed on a type 1?

[505197]

I always used the 4062 bugpack cam, the one engle I used I didn't like. Intresting idler you have there, we made a dual belt pulley that used the stock shims to adjust both inner and outter to the right tension. We had a lot of problems with belts when we ran light flywheels. We welded two bottoms togeather, then ground the flanges on the top pulley so we could weld the "original' outer to a modified inner, then use a stock idler in the "new location" , Try a 4062 next time, if theyre avaliab.

[idrivesafe]

Congratulations.. Nice Setup... (o\!/o)