Jig for ripping very narrow stock on a tablesaw
Loading...
Link to this comment:
Uploader Comments (stevemaskery)
All Comments (11)
-
Thank you, cheers mate.
-
The camera is way too far away, cannot see with detail what you're doing!
-
I just set the fence to thickness and rip the strips. Nothing to move and fast.
-
That kind of thin cutting is easy on a Martin sliding table saw with the rip fence pulled back behind the blade as measure for the cut thickness and then two eccentric lock handles to hold the work piece in place while cutting the narrow strips.
-
Nice, clean and informative. Thank you!
-
what a little beauty this jig is, i made one of these bad boys this morning, now i wonder how i coped without it.
I wonder what little wonders are one the dvd.....
-
Very informative video. Thanks for posting!
-
Nice and clear informative video, liked it. I'll be trying to make a similar jig for my table saw. Thanks
6:32Tablesaw finger saverby boughttheticket57,071 views
- 3:23Honor The Giants - 1080pby EcoSodaBlaster163,157 views
- 6:41CARSON WOODWORKS - Ripping Thin Stripsby flycastNW18,818 views
- 1:45Create a Crosscut Sled on the Cheap!by CurblyVideos76,047 views
- 7:47Creating box joints with a table sawby HampshireWaspcontrol22,079 views
- 3:06How to use the table saw!by RaiderMediaChannel17,592 views
- 2:10How to Plane a Board with a Router.movby Aviator1110054,385 views
- 7:18ultimate cross cut table for under 20 dollars s...by megakodeman23,036 views
- 2:32Worker killed when saw kicks backby WorkSafeBC33,185 views
- 2:01Box Joint How Toby clicclic9988,407 views
- 10:08Woodworking...A Dedicated Dado Sled for the Tab...by AppJourneyman41,559 views
- 9:24CUTTING THIN STRIPS ON A TABLE SAWby themasterwoodworker2,777 views
- 5:53INCRA LS Demo Part 3 of 3by incratools83,699 views
- 4:29Making dowelsby Matthiaswandel66,063 views
- 6:33Making A Stained Glass Wood Rose Window Frameby bestpushstick176,327 views
- 0:53How to cut perfect 90 and 45 degree miter anglesby MagicMitre223,461 views
- 6:52How to build a table saw sledby canadianhomeworkshop11,209 views
- 9:59Shop made Miter Fence - Accessory for the Super...by EagleLakeWoodworking128,584 views
- 8:45Avoiding Kickback on a Table Saw with a Splitte...by MicroJig13,331 views
I use my thicknesser with a wooden bed, this enables the machine's blades to go as low as i want and if they touch the wooden bed they just put a grove in it. with this wooden bed i can plane wood down to 1mm.
shipsboy 2 years ago
Yes, that's a good way, provided that yo can support thr timber. The risk is that strips that thin can shatter in a thicknesser. But yes it's a good way and I have a similar bed myself for work below 10mm, although I've never gone down to 1mm!
However, if you are preparing stock for lamination, you want to remove as little timber as possible, not just because of waste, but for grain preservation too, so I think a clean cut with a thin kerf blade is a better option in that case.
stevemaskery 2 years ago
Lucky you don't have to machine hundreds of lippings, you would be there all week.
Also notice you start the machine up with the timber right close to the blade, not very wise.
lynxuk2K 4 years ago
It's actually quite quick once you are set up, and no, I don't have to machine hundreds anyway.
The timber is well clear of the blade when I start up, held in place by the featherboard, so that I don't run the risk of pushing the featherboard too far forward as I start the cut.
Cheers
Steve
stevemaskery 4 years ago