hho stainless wire leads
Loading...
Loading...
877
views
Loading...
Uploader Comments (shamansays)
see all
All Comments (4)
-
I drew it flat by pulling it through the loop of an adjustable wrench laid flat on the floor and being stepped on.
Makes a very nice flat conductor.
Loading...
9:06
How to make a hydrogen 2 plate cell for under $5.by iamtheman6987,173 views- 5:01
HHO install in a 2006 Ram 1500 - 2by RadGenH2O25,985 views
- 10:15
HHO Gas 15 Pipe Assembly Test 4-24-2008 through 4-28-2008by pjckac151,575 views
- 9:52
HHO SWISS INOX 5 HOW TO BUILD HIGH PRODUCTION SPIRALSby ammanninox429,482 views
- 3:18
How to build HHO Generator. Video 1 of 3by mikejetmore90,220 views
- 10:37
A Real Life HHO Wiring Diagramby AlmostHydrogen80,901 views
- 9:11
HHO SWISS INOX 4 SPIRAL CELL + GAS PRODUCTION TESTSby ammanninox320,317 views
- 8:31
Hydrogen Cell HHO Dual 4 Wall Plate - Home Depot (PWM Test)by sirHOAX87,620 views
- 3:53
THE GREATEST HYDROGEN GENERATOR AVAILABLEby makefreegas445,192 views
- 8:05
scheme fuel cell with sponges in Stainless Steel HHO gasby alexblustar5,215 views
- 8:08
6 cell HHO unitby kentfromky2,403 views
- 3:41
013 hho generator test with water filters designby FIZZYH2O176,384 views
- 7:29
vehicle hho buildingby dfunishere1,398 views
- 4:32
HHO install in truck updateby shamansays6,201 views
- 6:29
HHO Torch Construction tips: tapping for the mig tipby KyHighlander595,662 views
- 9:59
hho How to build the(IMWSC)#70by josejir5,087 views
- 8:08
HHO 5.0 Plate Experimentby wHydrogen6,261 views
- 4:57
HHO 1.6LPMby hosnoopy2,869 views
- 6:35
How to assemble the HHO generator part 1by OriginalUncleNemo217,327 views
- 9:21
High-efficiency tri-cell electrolyzer assemblyby ardentscientist12,490 views
Cool idea.
cribcat1 3 years ago
If you twist it tight, fold it in half, twist again, then pound it flat, works pretty well.
shamansays 3 years ago
Yes, this is the video I stole... er... um... "borrowed" the idea from.
Within a few days of seeing this video, I dropped by Lowe's and bought me one of these tubes.
You may hve to double or triple up on the wires and run it through a piece of clear tubing, but I think it should work quite nicely.
This is a very slick idea, I will need to show you how I flattened it.
lutherp40 3 years ago
I like the tube idea.
shamansays 3 years ago
nice find ... suspect you will find your custom made wire gets a little hot though ... stainless aint the best of conductors ... the way most get around it is to use a pretty heavy duty hunk of stainless sheet bent to fit as a lead ... that way, it can handle the amps without getting so darn hot ... but let us know how your "make it work" works out ...
SmartScarecrow 3 years ago
What I ended up doing was clamping one end to a vice, and the other to my drill, stretched it out, and twisted it. I ran it at about 20 amps for about 30 min. and it seemed to hold up well.
shamansays 3 years ago