Antigravity Part 5 - The Vortex Coil (How to built)

Explaination on my antigravity own device based on reverse engineering of Victor Grebennikov - My World book. This video consist of 8 part which shows viewer step by step process to create antigravity platform during weekend project. Full explaination of the process were published inside my comment at "http://www.greenoptimistic.com/2008/03/05/how-to-build-an-ufo-like-anti-gravity­-spacecraft/" and "http://deackenz.wordpress.com/category/2-antigravity-theory/"

Malaysian Born Physicist
Deacken Frost
Copyright 2010

Category:

Science & Technology

Tags:

• vortex
• vortex coil
• victor grebennikov
• grebennikov
• UFO
• flying saucer
• gravity
• antigravity
• anti gravity
• stan deyo
• deyo
• malaysia
• cytotec
• flying platform
• biogravitic

[yablofon]

Victor Grebennikov discovered cavity structural effect. This is far from your assumptions. On your Rodin Coil

[deackenz]

@yablofon Are you sure? CSE only explain how to manipulate gravity by using certain geometric structure and dielectric material. Like from his book chapter 5.4 “from the notebook of a naturalist”, he explains that if you on the earth, which have a natural gravity pull, you can make gravity pull to be horizontal, spin, focus and even opposite to one another.

[deackenz]

@yablofon The end result after years of experimenting CSE, all you going to get is a good design of “cross-shifting filter under the platform board”, which create a uniform control in flight. But his book doesn’t explain how to make the gravity in the first place. This is what my reverse engineering and my short video is all about. So you can still continue your flight even in vast space between planet & stars.

[deackenz]

@superscraw I’d say yes, and depend on the intensity of the magnetic flux that been created by the 6 footer vortex coil. But, by creating AC magnetic flux, you can shield the cockpit with some aluminum plate, because in certain frequency, the AC magnetic flux can create skin magnetic effect and not penetrating the pilot cockpit. To see outside while stay behind the fully covered aluminum shield cockpit…no idea…LOL…

[ProblemMice]

@deackenz "Hope this reply helps."

I am sure it will. thanks bro.

[deackenz]

@ProblemMice to read Victor Grebennikov original (Russian) book, please visit bronzovka.ru / oglav.html (please repaste and delete the space from this address) then, use google translator to read up in english version. This translation method is better than you have the english version of the book because sometimes he use hidden meaning to actual of what he means. Hope this reply helps.

[ProblemMice]

@deackenz did you fly it? cool dude. I am about to start my own design. Any advise you can give will be welcome. I would really like to have a copy of his books in English.

[deackenz]

@xXPancake11 Any size of "Enameled Copper Wire" would be sufficient. For your further understanding of what "Enameled Copper Wire", please read more at Wikipedia "Enameled_wire". Which commonly known as magnet wire or winding wire which is widely use in transformer, speaker and electric motor coil.

[deackenz]

@justanuthrfobfan My prototype using 12VDC 40W florescent lamp inverter as AC solid state oscillator, one of important circuit to make it fly. This inverter require 12VDC 3.2A of input from small car battery (or power supply) and around 1000VAC 40mA of output. The frequency of the output will be around 13kHz. The frequency is not the case on getting the prototype to fly because the more frequency you use, the less vibrating your prototype will fly.

[deackenz]

@justanuthrfobfan - The flying part using backpack design will be shown on part 8 of the video, and the small flying prototype of my AC antigravity machine (aluminum disk shape with wooden tripod) will be shown on part 1 of the video. Stay tune. :-)