Permanent xbox360 Repair Tutorial RROD E 74 E68 ERROR & MORE

Permanent xbox360 repair tutorial
http://www.MyHotBuys.Us/
Tons Of Wholesale Xbox360 Games & Accessory's
http://www.MyHotBuys.Us/index.php?route=product/category&path=18

NEED HELP? VISIT OUR SITE AND GET HELP ON THE FORUMS
For this repair you also need
-Torx 8 Screwdriver/T8
-Torx 10 Screwdriver/T10
-A small flat screwdriver to open the back
All This & Entire Kits can Be Bought At http://www.MyHotBuy.Us/
This repair will work on allmost all RROD's especially on the ones with 0102 0020 as secondary code. It CAN also fix the one red light in the right bottom with an error code on screen like "e74" but only if it's the GPU if it's the ANA or HANA chip it can't (unless you're lucky with overheating)

I already fixed 12 xbox 360's like this but you have to use heatpaste because all things like that will make the fix permanent. Otherwise it will not last long, same thing when you don't overheat. Of course you can put alternative heatsyncs under the memory chips and tricks like that but it isn't the SOURCE of the problem, however it can be good to do.
http://www.MyHotBuys.Us/
You can also do this without attaching the motherboard to the steel case, like explained. If you want to do that use screws with a flat top which doen't get smaller 10 mm long (without the top) don't put STEEL washers under the motherboard if you do this.

Category:

Gaming

Tags:

• RROD
• red
• ring
• of
• death
• xbox
• 360
• games
• Microsoft
• warranty
• repair
• fix
• permanent
• easy
• guide
• x-clamp
• Heatpaste
• washers
• mod
• e74
• e-74
• error
• weapons

[devilsreject78]

yes, i have added a bunch of fans

[shaneme3]

@Music4Beats ps3 breaks down too, yo.

[diaboliq20]

@TheSaxplaya1 HAHAHA - you're such a dumb fuck - I do reflow and reballing of GPUs for a living

the xclamp replacement is a band aid at best - you're the one with the f*cked up facts - ask anyone that repairs consoles for a living.

If the solderballs under the GPU are broken or bridged, you're going to need a reflow at least - doing the xclamp and heat trick doesn't get the console anywhere near the 217 degrees u need to remelt the solder....don't u know anything f*ckface?

[boredezfuhhh]

@xXPAPAPWNAGEXx make sure you keep overheating it until you only have 2 lights,put the case back together, then you let it cool down overnight and turn on the xbox and it should work

[boredezfuhhh]

You actually need 16 nylon washers right? since you put one on both sides of the motherboard?

[sharker102]

@hellagoesdumb are you talking about the washers what people put clothes into?

[xXPAPAPWNAGEXx]

I need some advice, recently I've done this, took it apart, popped the heatsinks out, removed the old paste, used Arctic silver 5 then removed the x-clamps and used the screws with the metal and nylon washers, I put it back together and let it overheat, but once I started it back up from that it still showed 3 rings...do I need to keep trying to overheat or what?

[hellagoesdumb]

don't you need 16 nylon washers?

[benny3214]

At the end I was like beautiful

[KungPowCheekin]

@diaboliq20 yo i want to know if I take apart my 360 and do a reflow of the cpu/gpu of 750 F for 2 minutes then remove the paste and apply new thermal compound on the cpu/gpu then put everything back together will it work? i don't want to try these x clamp fixes/penny tricks since i am slightly confused about them. i did the method i had explained above on my playstation 3 but i know that is different but will it still work?

[360GamerJP]

@Iullian64 i'm no pro on xbox's but 2 things one yes your graphics are going, two your system is overheating if it has had a bad rrod fix

[StylesBoss]

I dont work 

[Iullian64]

what really is a e 74? Mine just displayed it. Is it over heating the motherboard. I saw lines in the screen, that is probably the graphics card?