Alert icon
We're changing our privacy policy. This stuff matters.  Learn more  Dismiss

Bedini Motor Progress 3

Loading...

Sign in or sign up now!
7,655
Loading...
Alert icon
Sign in or sign up now!
Alert icon

Uploaded by on Dec 31, 2007

Hello all!

So now I have done my motor, but it do not work, here the video about that.

I can make it spin by first 3 magnets, but then it stop by 3 and 4 magnets. Tonight I go back to my lab, and I have take of the circuit and make it whitout it, and tonight I hope it start working (tonight are my birdhday). So get gift for my self, if works.

But my question is: That battery what is charging, do in there have be 0 Volts? And in the "main" battery over 12V?

Thack You All! And Happy New Year!

Category:

Howto & Style

Tags:

License:

Standard YouTube License

  • likes, 2 dislikes

Link to this comment:

Share to:

Uploader Comments (Careica)

  • Fucking retard!!!!!! Idiot

  • You mean I am Idiot? By why way I am idiot? You tell me!

    You fucking cock-a-rocher, marcón cocksuccer! You will drink oil. We will drink clean and cheap water.

  • it looks like you have the coil wired backwards neg. battery cable goes to pos. side of coil

  • My God! Look at the other videos. I have maked it spin.

    Thank you!

Video Responses

see all

All Comments (17)

Sign In or Sign Up now to post a comment!
  • Your magnets arent good enough. You need neodymium magnets that you can get for cheap, or extract from old computer hard drive. You also need to put a lot more magnets. It kinda do a square wheel effect.

  • 1.the v pot you are using i used 1 time it will fail

    2.not enough magnets

    s the ssg guide lines would help u domt assume any thing hint fron zz is a i9 inch nonmagnet wheel-16-20 bar mag. if u want to get started i sugest join bedini monopole club .that coil is [if u got is a club or rick ssg it made for more mass in wheel @magnets

  • It ticks me off to see people say such things to people who dont deserve it!.... Sorry, people do that to u Michael...

  • Get a life and dont say that ok!? You obviously don't know how this works.

  • Thank you for those advices. I have got my bedini motor run, if you watch other bedini videos.

    But still, Thank You!

  • I wanted to do a scrap motor and entirely did it. Of course I tryed 2 weeks before it even resonate. The key was a lower pulse rate to obtain the right frequency - resistor to 0 then replaced with 1Kohm

    I managed not to smoke any transistor: Neon bulb between Emitor and Colector & 2W12V bulb series with resistor - lights up when the resistor is 0.

    Oh, and a last advice: rotate faster to start the motor - you need 150mA and at least 5V in the Base of the (no matter) Tr to cuplate

    Don`t give up!

  • Main is humming, all right, but if I short the resistor to 0 the humming stops, the motor works just fine but speeds up, sucking a greater current though, and the output voltage drops a little.

    There are a lot of variables here, as nobody can actually measure the relation between:

    - wire diameter/conductivity constant

    - disk diameter

    - capacitance & inductance of the conecting wires

    - inductance of the coils

    - power AND SECTION of the magnets

Loading...
0 / 00Unsaved Playlist Return to active list
    1. Your queue is empty. Add videos to your queue using this button:
      or sign in to load a different list.
    Loading...Loading...Saving...
    • Clear all videos from this list
    • Learn more