Trunking Across Cisco 2950 Switches - CCNA
Loading...
Link to this comment:
Uploader Comments (paulwbrowning)
All Comments (17)
-
Hi Paul, and thanks for the viedo.
I did the same but when I connect the two ports together they show orange light then shout down!!
I got the following msg:
Received BPDU on port Fa0/1 with BPDU Guard enabled. Disabling port.
any suggestion
-
hi Paul, to put a range of port in one vlan the int range command does not work in config mode in 2950 switch. could you please tell me how to put rang of port in one vlan?
-
hey everyone i have a question. is it obligatory for EIGRP routing to put a loopback ip? plis im getting into this world and i dont know much about it. sorry for my bab english i don really speak it. Dominicano. Thanks S
-
@itikabc There is no need for static route settings. All 3 routers are on the same network which is 192.168.1.0 . If , for example, you change one of the above routers ip address to 192.168.5.1, then you would need to include static or dynamic routing protocol.
-
So in this kind of configuration. Where do you configure the static routing? On all the three router?
-
Mr Paulbrowning, thank you so much..very systematic, step by step explanation..i had a whole host of problems with my trunking and vlan configurations..i followed closely every second of this video.and was able to rectify every single mistake i made..thank you so much once again...=)
-
ssh runs on port 22.
-
Sorry I just saw they are in the same subnet
-
I'm new in Networking.Explain me.How can the FastEth of the Router comunicat with each other if they are in different subnetwork?
-
Should VLAN 2 already be accessible on Switch 2 with VTP?
8:33Trunkingby jjc041918,202 views
- 5:04CCNA 3 - VLAN Trunking Protocol or VTPby ReasonablePrices14,979 views
- 4:39Network Wiring Closet - router DSL line -part1by egmilian53,250 views
- 0:31passwd recoveryby jchimbault2,458 views
- 2:36CCNA -VLAN's and Trunkingby nhancedlearning20,166 views
- 8:37Configure Static VLAN for CCNAby kogula1428,567 views
- 0:30Setting an IP address and Default Gateway on a ...by AnythingOverIP20,317 views
- 4:34Cisco CCNA 640-802 Live Labs from www.affordabl...by LiveTrain102,979 views
- 3:54Network Simulationby zaghy2zy243,141 views
- 8:03802.1Q and Trunking 101by Keith678312,430 views
- 7:58CCNA - Wireless LANsby ToddLammle14,319 views
- 1:32New Cisco Switch Power Up 2950by djrikk21421,443 views
- 4:16Cisco switch setup with Cisco Helperby theacademypro7,034 views
- 4:10Learn how to create a dot1q trunk (802.1q) conf...by ccieadvisor1,933 views
- 8:16VTP Modesby mrsquizz4,008 views
- 5:08CCNA 3 - Part 2 - Basic Switch Concepts and Co...by ReasonablePrices33,757 views
- 8:15Switchport Securityby kenny50453,791 views
- 2:41Cisco Crossover Cable for Router Connectionsby diablocable136,227 views
- 8:20Cisco LAN Switching Overview - Part 2by RouteHub9,045 views
- 8:20Cisco LAN Switching Overview - Part 1by RouteHub8,929 views
Oh,
you have to permit SSH on the router. I will have to check on that. I do have a SDM video on YouTube with the commands.
Paul
paulwbrowning 3 years ago
hi paul i believe it was you the other day posted a vid about hyperterminal i wanted to know whether if it does support ssh as well ? telnet works but for ssh it doesnt connect wheres the problem ? thanks :)
thejokermansending 3 years ago
Hi,
I don't understand your questions sorry.
Paul
paulwbrowning 3 years ago