GSXR SET VALVE REMOVED SOUND
Loading...
Uploader Comments (jared0401)
All Comments (10)
-
where is the set valve on the k4 model thxs
-
The throttle is much more responsive without the set valve.
-
this guy is an idiot too.
-
how much was it is and where to get it n u think it is louder than a jardine gp1
-
You are correct. Watch my GSXR SET Valve Removal Video and I show you exactly how it works. It's about 1/4 on idle.
-
PS: Unfair video too, the SET does not stay closed at idle nor when you pull on the gas like you portray it on the video when you manually close it all the way to show the sound difference. In fact its 1/3 open at idle and then progressively opens all the way at 6k RPM under acceleration.
-
Placebo effect. You didnt gain any HP The valve is FULL OPEN after 6k RPM. Same as when u removed the cables, same exhaust flow. You lost low end torque, but louder sound at idle-3k RPM gave you the illusion that you did not lose torque....you did! Only way you could gain HP is if removed SET because of an FI light or without adjusting it as per your manual's specs at 600 miles and 7500 thereafter. In that case it was robbing you of HP and hence when you removed it it felt like breathing better
3:17
How to set a gsxr 600, 750, 1000 shift lightby Supratt8827,895 views- 0:31
FI Light Fixby elyte13,075 views
- 0:55
K7 GSXR 600 Straight Pipeby subarustein130,838 views
- 11:01
How to check valve clearances and how to shim them (PART 2) (Watch in HD!)by RandomWeekendVideo34,712 views
- 0:46
2010 R1 Toce exhaustby dietzpat857,445 views
- 6:22
Valve Adjustments - Part 1by dodgerider2674,940 views
- 1:01
(Part 3)YAMAHA R1 Valve Clearance(SINGAPORE)www.teamhklracing.comby teamhklracing8,394 views
- 0:28
Fly by 2007 GSX-R 600 Two Brothers Shorty systemby SuzukiGSXR4LIFE8,229 views
- 1:59
bike wont startby dangerdan8716,636 views
- 4:51
Suzuki GSXR Windscreen Installation Guide from Hotbodies Racingby HotbodiesRacingInc8,071 views
- 2:49
My Mom on my GSX-R 1000 for a little cruise around the blockby tylerdirden1980242,739 views
- 1:23
Suzuki GSX-R modified headlight by CiNcity Designsby CiNcityDesigns93,727 views
- 1:50
Yoshimura GP EVO / GSX-R 600by trakya7928,812 views
- 0:29
GSXR 750 w/ D&D exhaustby rebelus471,023 views
- 0:23
GSXR 600 k8 Yoshimura R55by fdl516,185 views
- 0:07
Dropped Valve on the R1by Chaos06919,366 views
- 11:07
2007 Gsxr 750 check valve removal modby cesdog292,233 views
- 9:34
Basic Motorcycle Maintenence Oil and Oil Filter Change Part 5/5by wedginator5,889 views
- 1:06
RLS Exhaust Torque Seriesby RickySutton7610,144 views
Can you just remove the cables and leave all the crap in there or do you have to remove all the equipment
64thAGGRESSOR 3 years ago
remove the cables and you gotta cut a wire, and I removed the servo motor out of the right side tail section. The butterfly valve is still in the header just FULL OPEN. if your going to do it @ least remove the big shit
jared0401 3 years ago
is that a k7 or k6?
i have a k8 and i know the ecu wiring is different than the k7 and k6..
did you lose your low end torque?
NEMES1Sx1st 3 years ago
Its a K6 and I did not lose any low end.. some noticeable power gain if you dyno the bike. More than anything it took off very few pounds and made the bike louder.. Thats about it
jared0401 3 years ago