Changing pump oil in vintage sea-doo part 1of 2
Loading...
Loading...
46,511
Loading...
Uploader Comments (cuv4xd)
see all
All Comments (20)
-
Good tutorial. Thanks!
-
great video , forget the naysayers.
-
Good video!!!!...Helped me for sure!!!
-
LOl,, i know, i just pull mine off and the oil does Stinks
-
@newt20002 cause it was dirty
clean it reglruy and your good
-
lol thats rip off way lol
Loading...
8:06
Changing pump oil in vintage sea-doo part 2 of 2by cuv4xd38,798 views- 1:21
Sea-Doo How to diagnose wear ringby cuv4xd80,383 views
- 3:53
How to replace sea-doo wear ring in 5 minutes.by cuv4xd5,813 views
- 1:03
jet ski made in china engine testby benawadh56,551 views
- 4:21
SeaDoo Safetyby PhotoJohnW24,842 views
- 1:04
Sea-Doo greasing the drive shaftby cuv4xd28,327 views
- 0:32
13b engine in a seadoo speedsterby mazdooo81,898 views
- 4:16
1995 Seadoo XP Part 1 Pump Removalby LonnieJohnson11,815 views
- 0:37
How not to ride a SeaDooby dm996c4s103,157 views
- 9:41
2 stroke Rebuild 670 Rotaxby 1skiinIan122,882 views
- 0:31
Horrible Seadoo Crash caught on tape !by Masternode294,282 views
- 9:49
How To Change a Seat Coverby motosportoutlet32,872 views
- 0:24
05 Sea Doo RXP RUNS AGAIN AFTER DROWNINGby ThePWC6,875 views
- 7:54
How to winterize a jet skiby chorstma4445,759 views
- 2:41
Blown Bombardier Rotax 462 engineby 1skiinIan72,318 views
- 1:17
how to change oil filter jet skiby arturosousa5,761 views
- 1:12
WORLD'S FASTEST JET-SKIby iLikeBoatsThatGoFast140,667 views
- 4:44
Sea-doo anti rattle cone kit how and why it works thousands sold 100% works!by MaulinMarto50,906 views
- 4:07
SEADOO WAKEby GWARREN23,369 views
- 3:47
N0.8 and Sea-Doo rescueby Southendjetskiclub20,910 views
Using a wrench like a dumb ass, 93 xp pos 200.00 ski locked to the trailer. I put a trash bag in the bucket so I can toss the oil in the trash like a dumb fuk. Good instruction video, teaching us how to bang on shit. You stupid fuk. That stuff stinks just like this video, You're amazing wish you were my father.
lilcritchy 7 months ago
@lilcritchy Just watched YOUR vid. Your a stupid disrespectful punk kid who hasn't grown up yet. I'll leave your stupid comment here for a bit so others may witness what a 89 IQ looks like. You should become a cop and fight against Liberty and Freedom. And before I block you, good luck in life looser.
cuv4xd 7 months ago 2
how can i remove the bearing from the housing,i just orderd a new housing pump 3 vanes were almost gone,guy at the dealer said check ur bearings and if good use the same ones,
Zpe3ddyGonzalexx 7 months ago in playlist power jet
@Zpe3ddyGonzalexx I used a socket extension, and by going through from the opposite end and just catching the edge of the bearing, I taop it out slowly and carefuly. You'll want to change position of the tool often while doing this process so it comes out 'square'. Don't force it, just take your time. Use a large socket as a tool when installing the new one from the outside of the pump. Tape the socket evenly across the surface and it will seat the new one. (Remember how it should look)
cuv4xd 7 months ago
this video was 5 and a half minutes to long
motogreg 1 year ago
@motogreg Sorry you didn't find it helpful. Perhaps you are best to look elsewhere. Bye bye.
cuv4xd 1 year ago